WEG CFW100 series Manuel utilisateur

Motors | Automation | Energy | Transmission & Distribution | Coatings

Frequency Inverter

Convertidor de Frecuencia

Inversor de Frequência

CFW100 V3.1X

Quick Reference of Parameters, Alarms and Faults

Referencia Rápida de los Parámetros, Alarmas y Fallas

Referência Rápida dos Parâmetros, Alarmes e Falhas

Quick Reference of Parameters, Alarms and Faults

Series: CFW100

Language: English

Document: 10006259370 / 01

Software version: 3.1X

Build 1180

Publication Date: 04/2019

SUMMARY OF REVISIONS

Version Revision Description

3.0X R00 First edition.

3.1X R01 General Revision.

English

QUICK REFERENCE OF PARAMETERS, ALARMS AND FAULTS

Param. Description Adjustable Range Factory Setting Prop.

P000 Access to Parameters 0 to 9999 1

P001 Speed Reference 0 to 9999 ro

P002 Output Speed (Motor) 0 to 9999 ro

P003 Motor Current 0.0 to 10.0 A ro

P004 DC Link Voltage 0 to 524 V ro

P005 Output Frequency (Motor) 0.0 to 400.0 Hz ro

P006 Inverter Status 0 = Ready

1 = Run

2 = Undervoltage

3 = Fault

4 = Self-Tuning

5 = Conﬁguration

6 = DC Braking

7 = Reserved

8 = Fire Mode

P007 Output Voltage 0 to 240 V ro

P009 Motor Torque -200.0 to 200.0 % ro, VVW

P011 Power Factor 0.00 to 1.00 ro

P012 DI8 to DI1 Status 0 to FF (hexa)

Bit 0 = DI1

Bit 1 = DI2

Bit 2 = DI3

Bit 3 = DI4

Bit 4 = DI5

Bit 5 = DI6

Bit 6 = DI7

Bit 7 = DI8

P013 (*) DO3 to DO1 Status 0 to 7 (hexa)

Bit 0 = DO1

Bit 1 = DO2

Bit 2 = DO3

P014 (*) AO1 Value 0.0 to 100.0 % ro

P018 (*) AI1 Value -100.0 to 100.0 % ro

P020 (*) Potentiometer Signal Value -100.0 to 100.0 % ro

P022 FI Value in Hz 0 to 3000 Hz ro

P023 Main SW Version 0.00 to 99.99 ro

P024 (*) Accessory SW Version 0.00 to 99.99 ro

P027 Accessory Conﬁg. 0 = Without Accessory

1 = CFW100-HMIR

2 = CFW100-IOAR

3 = CFW100-CCAN

4 = CFW100-CBLT

5 = CFW100-IODR

6 = CFW100-IOADR

7 = CFW100-IOA

8 = CFW100-IOD

9 = Reserved

10 = CFW100-IOP

P029 Power HW Conﬁguration 0 to 999 According to the

Inverter Model

P030 Module Temperature -200.0 to 200.0 ºC ro

P037 Motor Overload Ixt 0.0 to 100.0 % ro

P038 (*) Encoder Speed 0 to 270F (hexa) ro

P039 (*) Encoder Pulses Count 0 to FFFF (hexa) ro

P045 Fan Enabled Time 0 to FFFF (hexa) ro

P047 CONF Status 0 to 33 (Table 1.1 on page 23) ro

P048 Present Alarm 0 to 999 ro

P049 Present Fault 0 to 999 ro

P050 Last Fault 0 to 999 ro

P051 Current At Last Fault 0.0 to 10.0 A ro

P052 DC Link At Last Fault 0 to 524 V ro

P053 Frequency At Last Fault 0.0 to 400.0 Hz ro

P054 Temperature Last Fault 0.0 to 200.0 ºC ro

P060 Second Fault 0 to 999 ro

P070 Third Fault 0 to 999 ro

P080 Last Fault on Fire Mode 0 to 999 ro

P081 Second Fault on Fire Mode 0 to 999 ro

CFW100 | 5

English

QUICK REFERENCE OF PARAMETERS, ALARMS AND FAULTS

Param. Description Adjustable Range Factory Setting Prop.

P082 Third Fault on Fire Mode 0 to 999 ro

P100 Acceleration Time 0.1 to 999.9 s 5.0 s

P101 Deceleration Time 0.1 to 999.9 s 10.0 s

P102 Acceleration Time 2nd Ramp 0.1 to 999.9 s 5.0 s

P103 Deceleration Time 2nd Ramp 0.1 to 999.9 s 10.0 s

P104 Ramp S 0 = Inactive

1 = Active

0 cfg

P105 1st / 2nd Ramp Selection 0 = 1st Ramp

1 = 2nd Ramp

2 = DIx

3 = Serial/USB

4 = Reserved

5 = CO/DN

6 = SoftPLC

P106 Emer. R. Acceleration Time 0.1 to 999.9 s 5.0 s

P107 Emer. R. Time Deceleration 0.1 to 999.9 s 5.0 s

P120 Speed Ref. Backup 0 = Inactive

1 = Active

2 = Backup by P121

P121 Reference via HMI 0.0 to 400.0 Hz 3.0 Hz

P122 JOG Reference -400.0 to 400.0 Hz 5.0 Hz

P124 Multispeed Ref. 1 -400.0 to 400.0 Hz 3.0 Hz

P125 Multispeed Ref. 2 -400.0 to 400.0 Hz 10.0 (5.0) Hz

P126 Multispeed Ref. 3 -400.0 to 400.0 Hz 20.0 (10.0) Hz

P127 Multispeed Ref. 4 -400.0 to 400.0 Hz 30.0 (20.0) Hz

P128 Multispeed Ref. 5 -400.0 to 400.0 Hz 40.0 (30.0) Hz

P129 Multispeed Ref. 6 -400.0 to 400.0 Hz 50.0 (40.0) Hz

P130 Multispeed Ref. 7 -400.0 to 400.0 Hz 60.0 (50.0) Hz

P131 Multispeed Ref. 8 -400.0 to 400.0 Hz 66.0 (55.0) Hz

P133 Minimum Frequency 0.0 to 400.0 Hz 3.0 Hz

P134 Maximum Frequency 0.0 to 400.0 Hz 66.0 (55.0) Hz

P135 Maximum Output Current 0.0 to 40.0 A 1,5 x Inom V/f

P136 Manual Torque Boost 0.0 to 30.0 % According to the

Inverter Model

V/f

P137 Automatic Torque Boost 0.0 to 30.0 % 0.0 % V/f

P138 Slip Compensation -10.0 to 10.0 % 0.0 % V/f

P139 Output Current Filter 0.000 to 9.999 s 0.050 s V/f, VVW

P140 Slip Com. Filter 0.000 to 9.999 s 0.500 s VVW

P142 Maximum Output Voltage 0.0 to 100.0 % 100.0 % cfg, V/f

P143 Intermediate Output Voltage 0.0 to 100.0 % 50.0 % cfg, V/f

P145 Field Weakening Speed 0.0 to 400.0 Hz 60.0 (50.0) Hz cfg, V/f

P146 Intermediate Frequency 0.0 to 400.0 Hz 30.0 (25.0) Hz cfg, V/f

P149 DC Link Comp. Mode 0 = Inactive

1 = Standard

2 = Overmodulation

3 = Extended

1 cfg, V/f

P150 DC/LC Regul. Type 0 = hold_Ud and decel_LC

1 = accel_Ud and decel_LC

2 = hold_Ud and hold_LC

3 = accel_Ud and hold_LC

0 cfg, V/f, VVW

P151 DC Link Regul. Level 325 to 460 V 430 V (P296 = 1)

380 V (P296 = 2)

781 V (P296 = 4)

781 V (P296 = 5)

781 V (P296 = 6)

781 V (P296 = 7)

V/f, VVW

P156 Rated Speed Overload Current 0.1 to 40.0 A 1,2 x Inom

P157 Overl.Curr.50 % Speed 0.1 to 40.0 A 1,2 x Inom

P158 Overl.Curr.20 % Speed 0.1 to 40.0 A 1,2 x Inom

P178 Rated Flux 50.0 to 150.0 % 100.0 % VVW

P200 Password 0 = Inactive

1 = Active

2 to 9999 = New Password

0 cfg

6 | CFW100

English

QUICK REFERENCE OF PARAMETERS, ALARMS AND FAULTS

Param. Description Adjustable Range Factory Setting Prop.

P202 Type of Control 0 = V/f

1 = Quadratic V/f

2 to 4 = Not Used

5 = VVW

0 cfg

P204 Load/Save Parameters 0 to 4 = Not Used

5 = Load 60 Hz

6 = Load 50 Hz

7 = Load User

8 = Not Used

9 = Save User

10 = Not Used

11 = Load Default SoftPLC

12 to 13 = Reserved

0 cfg

P205 Main Display Parameter 0 to 999 2

P207 Bar Graph Parameter 0 to 999 3

P208 Ref. Scale Factor 1 to 9999 600

P209 Ref. Eng. Unit 0 to 1 = Without unit

2 = Volt (V)

3 = Hertz (Hz)

4 = Without unit

5 = Percent ( %)

6 = Without unit

7 = Rotation/min. (rpm)

P210 Ref. Decimal Point 0 = wxyz

1 = wxy.z

2 = wx.yz

3 = w.xyz

P213 Bar Scale Factor 1 to 9999 1,0 x Inom

P219 Red. Switch. Freq. 0.0 to 15.0 Hz 5.0 Hz cfg

P220 LOC/REM Selection Source 0 = Always Local

1 = Always Remote

2 to 3 = Not Used

4 = DIx

5 = Serial/USB (LOC)

6 = Serial/USB (REM)

7 to 8 = Not Used

9 = CO/DN (LOC)

10 = CO/DN (REM)

11 = SoftPLC

0 cfg

P221 LOC Reference Sel. 0 = HMI

1 = AI1

2 = Not Used

3 = Potentiometer

4 = FI

5 to 6 = Not Used

7 = E.P.

8 = Multispeed

9 = Serial/USB

10 = Not Used

11 = CO/DN

12 = SoftPLC

13 = Not Used

14 = AI1 >0

15 = Not Used

16 = Potentiometer >0

17 = FI >0

0 cfg

P222 REM Reference Selection See options in P221 2 cfg

P223 LOC FWD/REV Selection 0 = Foward

1 = Reverse

2 to 3 = Not Used

4 = DIx

5 = Serial/USB (FWD)

6 = Serial/USB (REV)

7 to 8 = Not Used

9 = CO/DN (FWD)

10 = CO/DN (REV)

11 = Not Used

12 = SoftPLC

0 cfg

P224 LOC Run/Stop Sel. 0 = HMI Keys

1 = DIx

2 = Serial/USB

3 = Not Used

4 = CO/DN

5 = SoftPLC

0 cfg

CFW100 | 7

English

QUICK REFERENCE OF PARAMETERS, ALARMS AND FAULTS

Param. Description Adjustable Range Factory Setting Prop.

P225 LOC JOG Selection 0 = Disabled

1 = Not Used

2 = DIx

3 = Serial/USB

4 = Not Used

5 = CO/DN

6 = SoftPLC

1 cfg

P226 REM FWD/REV Selection See options in P223 4 cfg

P227 REM Run/Stop Selection See options in P224 1 cfg

P228 REM JOG Selection See options in P225 2 cfg

P229 Stop Mode Selection 0 = Ramp to Stop

1 = Coast to Stop

0 cfg

P230 Dead Zone (AIs and FI1 ) 0 = Inactive

1 = Active

0 cfg

P231 (*) AI1 Signal Function 0 = Speed Ref.

1 to 3 = Not Used

4 = PTC

5 to 6 = Not Used

7 = PLC Use

8 = Application Function 1

9 = Application Function 2

10 = Application Function 3

11 = Application Function 4

12 = Application Function 5

13 = Application Function 6

14 = Application Function 7

15 = Application Function 8

16 = Control Setpoint

17 = Process Variable

0 cfg

P232 (*) AI1 Input Gain 0.000 to 9.999 1.000

P233 (*) AI1 Input Signal 0 = 0 to 10 V / 20 mA

1=4to20mA

2=10V/20mAto0

3=20to4mA

P234 (*) AI1 Input Offset -100.0 to 100.0 % 0.0 %

P235 (*) AI1 Input Filter 0.00 to 16.00 s 0.00 s

P241 (*) Potentiometer Signal Function 0 = Speed Ref.

1 to 6 = Not Used

7 = SoftPLC

8 = Application Function 1

9 = Application Function 2

10 = Application Function 3

11 = Application Function 4

12 = Application Function 5

13 = Application Function 6

14 = Application Function 7

15 = Application Function 8

16 to 17 = Not Used

0 cfg

P242 (*) Potentiometer Signal Gain 0.000 to 9.999 1.000

P244 (*) Potentiometer Signal Offset -100.0 to 100.0 % 0.0 %

P245 Potentiometer and FI1 Filter 0.00 to 16.00 s 0.00 s

P246 FI1 Input Function 0 = Inactive

1 = Active in DI1

2 = Active in DI2

3 = Active in DI3

4 = Active in DI4

0 cfg

P247 FI1 Input Gain 0.000 to 9.999 1.000

P248 FI1 Minimum Input 1 to 3000 Hz 100 Hz

P249 FI1 Input Offset -100.0 to 100.0 % 0.0 %

P250 FI1 Maximum Input 1 to 3000 Hz 1000 Hz

8 | CFW100

English

QUICK REFERENCE OF PARAMETERS, ALARMS AND FAULTS

Param. Description Adjustable Range Factory Setting Prop.

P251 (*) AO1 Output Function 0 = Speed Ref.

1 = Not Used

2 = Real Speed

3 to 4 = Not Used

5 = Output Current

6 = Not Used

7 = Active Current

8 to 10 = Not Used

11 = Motor Torque

12 = SoftPLC

13 to 15 = Not Used

16 = Motor Ixt

17 = Not Used

18 = P696 Value

19 = P697 Value

20 = Not Used

21 = Application Function 1

22 = Application Function 2

23 = Application Function 3

24 = Application Function 4

25 = Application Function 5

26 = Application Function 6

27 = Application Function 7

28 = Application Function 8

29 = Control Setpoint

30 = Process Variable

P252 (*) AO1 Output Gain 0.000 to 9.999 1.000

P253 (*) AO1 Output Signal 0 = 0 to 10 V

1=0to20mA

2=4to20mA

3=10to0V

4=20to0mA

5=20to4mA

P263 DI1 Input Function 0 = Not Used

1 = Run/Stop

2 = General Enable

3 = Quick Stop

4 = Foward Run

5 = Reverse Run

6 = Start

7 = Stop

8 = Direction of Rotation

9 = LOC/REM

10 = JOG

11 = Accelerate E.P.

12 = Decelerate E.P.

13 = Multispeed

14 = 2nd Ramp

15 to 17 = Not Used

18 = No Ext. Alarm

19 = No Ext. Fault

20 = Reset

21 to 23 = Not Used

24 = Disab.FlyStart

25 = Not Used

26 = Lock Prog.

27 to 31 = Not Used

32 = 2nd Ramp Multispeed

33 = 2nd Ramp Increase E.P.

34 = 2nd Ramp Decrease E.P.

35 = 2nd Ramp FWD Run

36 = 2nd Ramp REV Run

37 = Start / Inc. E.P.

38 = Dec. E.P. / Stop

39 = Stop

40 = Safety Switch

41 = Application Function 1

42 = Application Function 2

43 = Application Function 3

44 = Application Function 4

45 = Application Function 5

46 = Application Function 6

47 = Application Function 7

48 = Application Function 8

49 = Enable Fire Mode

50 to 54 = Not Used

55 = Run/Stop with Line Start Lockout

1 cfg

CFW100 | 9

English

QUICK REFERENCE OF PARAMETERS, ALARMS AND FAULTS

Param. Description Adjustable Range Factory Setting Prop.

P264 DI2 Input Function 0 = Not Used

1 = Run/Stop

2 = General Enable

3 = Quick Stop

4 = Foward Run

5 = Reverse Run

6 = Start

7 = Stop

8 = Direction of Rotation

9 = LOC/REM

10 = JOG

11 = Accelerate E.P.

12 = Decelerate E.P.

13 = Multispeed

14 = 2nd Ramp

15 to 17 = Not Used

18 = No Ext. Alarm

19 = No Ext. Fault

20 = Reset

21 to 23 = Not Used

24 = Disab.FlyStart

25 = Not Used

26 = Progr. Off

27 to 31 = Not Used

32 = 2nd Ramp Multispeed

33 = 2nd Ramp Increase E.P.

34 = 2nd Ramp Decrease E.P.

35 = 2nd Ramp FWD Run

36 = 2nd Ramp REV Run

37 = Turn ON / Ac. E.P.

38 = De. E.P. / Turn OFF

39 = Stop

40 = Safety Switch

41 = Application Function 1

42 = Application Function 2

43 = Application Function 3

44 = Application Function 4

45 = Application Function 5

46 = Application Function 6

47 = Application Function 7

48 = Application Function 8

49 = Enable Fire Mode

50 = PID Manual / Automatic

51 to 54 = Not Used

55 = Run/Stop with Line Start Lockout

8 cfg

10 | CFW100

Autres manuels pour CFW100 series

Table des matières

Langues :

Autres manuels WEG Entraînement CC

WEG

WEG CFW500 V1.8X Manuel du propriétaire

WEG

WEG CFW-09 Manuel utilisateur

WEG

WEG AFW900 Manuel utilisateur

WEG

WEG CFW-11 Series Manuel utilisateur

WEG

WEG MVW3000 Series Manuel du propriétaire

WEG

WEG CFW-11 Series Manuel utilisateur

WEG

WEG CFW-11 Series Manuel utilisateur

WEG

WEG CFW100 series Manuel utilisateur

WEG

WEG W21 Manuel utilisateur

WEG

WEG bacnet CFW701 Manuel utilisateur

WEG

WEG CFW-11 Series Manuel utilisateur

WEG

WEG DeviceNet CFW500 Instructions d'utilisation

WEG

WEG CFW100 series Manuel du propriétaire

WEG

WEG CFW300-KHMIR Guide rapide

WEG

WEG CFW-11W Instructions d'installation et d'utilisation

WEG

WEG DeviceNet CFW500 Manuel utilisateur

WEG

WEG CFW-11 Series Manuel utilisateur

WEG

WEG CFW11M G2 Series Manuel utilisateur

WEG

WEG SCA06 Manuel utilisateur

WEG

WEG CFW100 series Manuel du propriétaire

WEG

WEG DeviceNet CFW500 Manuel utilisateur

WEG

WEG MVW3000 Series Manuel utilisateur

WEG

WEG Easy Drive CFW10 Manuel utilisateur

WEG

WEG DeviceNet CFW500 Manuel utilisateur

Manuels Entraînement CC populaires d'autres marques

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces

Chamberlain Garog

Chamberlain Garog D Series Manuel utilisateur

Parker

Parker PDS Series Manuel utilisateur

Festo

Festo DGC G Series Guide de configuration

Binks

Binks QS-5012-1-CE Manuel utilisateur

Danfoss

Danfoss VLT 2800 Series Fiche technique

ABB

ABB ACQ580-01 Series Manuel d'installation

YASKAWA

YASKAWA CANopen SI-S3 Manuel utilisateur

GE D20A6 Manuel utilisateur

Unex

Unex MC-D-250-1000-050W-TW Manuel utilisateur

Geckodrive

Geckodrive G213V Manuel utilisateur

ABB

ABB RSYC-01 Manuel utilisateur

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuel du propriétaire

Siemens

Siemens SINAMICS G Fiche technique

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Mode d'emploi

SOMFY

SOMFY JR RU 30 Manuel utilisateur

Beckhoff

Beckhoff AX8911 Manuel de l'opérateur