Wayne DW-10 Manuel d'installation
Operation
DW-10 and DW-12 Dispenser Printers
P/N 000-920921-
Rev D
READ THIS MANUAL BEFORE YOU BEGIN
Dispensers have both electricity and a hazardous, flammable and potentially explosive
liquid. Failure to follow the below precautions and the Warning and Caution instructions in
this manual may result in serious injury. Follow all rules, codes and laws that apply to your
area and installation.
SAFETY PRECAUTIONS
Make sure that you know how to turn OFF power to the dispenser and submersible
pumps in an emergency.
Be sure to adhere to the list of cautions contained in this manual for the DW-10 and
DW-12 printers.
HOW TO CONTACT WAYNE
Trouble with the operation of the printer should be referred to your authorized Wayne ser-
vice personnel or the Wayne Help Desk (1-800-289-2963).
Contents
Title Page
1 Introduction 1
1.1 Paper Type 1
2 Printer Operation 3
2.1 Controls and Indicator Lights 3
2.2 Opening/Closing Printer Door 4
2.3 Loading Paper 5
2.4 Internal Components Clearing Paper Jams 7
2.5 Setting the Paper Width Adjust Lever 7
2.6 Low Paper Sensor Position 8
3 Error Lights and Paper Jams 9
3.1 Error Lights 9
3.2 Clearing Paper Jams 10
4 Safety Precautions 12
5 Service Technician Information 14
5.1 DIP Switch Settings 14
5.2 Component Locations 15
5.3 Tech Tip 16
5.4 Printer Part Numbers 16
_____________________________________________________________________________________i
P/N 000-920921- Rev 0D 04/2015
ii____________________________________________________________________________________
P/N 000-920921- Rev 0D 04/2015
1 INTRODUCTION
This manual explains the operation of Wayne DW-10 and DW-12 thermal printers used
in Wayne Vista™ and Ovation™ fuel dispensers. The manual contains typical operator
procedures, which includes loading paper, use of the proper paper, clearing paper jams
and a list of printer precautions. The manual also contains a section on service for
Wayne certified technicians.
Once the printer door on the dispenser is unlocked and opened, the printer will appear
as shown in the photo below.
1.1 Paper Type
The recommended paper is the Wayne thermal printer paper, part number 7000701 for
1 Roll and part number 7000703 for a box of 48 Rolls. Paper used in the printershould
comply with specifications of the Wayne paper.
Other printer papers that meet our paper specification include Kansaki P-350 and
Koehler KT55F18 papers with the following:
Inside Core Diameter .68"-.79"
Core Annular Thickness .10"-.28"
Paper and Core Width 2.32"-2.36"
Finished Roll Diameter 3.80"-4.00"
Paper should not be stuck to the core with adhesive.
See cautions concerning paper types on the next page.
_____________________________________________________________________________________1
P/N 000-920921- Rev 0D 04/2015
1.2 Paper Type, continued
Adhere to the cautions below when using or when storing the paper.
Caution:
Avoid allowing the surface of the paper to contact with chemicals or oils as
this may cause the paper to become colored or the printed data on it may
become erased.
Avoid scraping on the paper surface with your nail or a metal object as this
may cause the surface of heat-sensitive paper to become colored.
Do not expose the paper to the effects from heat, humidity, or sunlight as
heat-sensitive paper starts getting colored at approx. 70 degrees.
2____________________________________________________________________________________
P/N 000-920921- Rev 0D 04/2015
2 PRINTER OPERATION
2.1 Controls and Indicator Lights
* HEXADECIMAL DUMP mode:
If the TEST button is pressed and held for more than 10 seconds, printer will switch to
HEX-DUMP mode.
POWER light starts flashing and all received data will be printed as hexadecimal codes.
To exit the HEX-DUMP mode, press the TEST button briefly and release.
PRINTER INFO:
When the printer door is opened and then closed, the Wayne print out shown above is printed.
This printout includes printer Model name, Firmware version, baud rate, DIP switches, and
built-in fonts.
Front Door Pull
Down Handle
Paper Exit
ERROR Light
Red light is on steady
or blinks to show
different errors.
POWER Light
Green light is on
steady when printer
power is on.
FEED Button
Feeds paper while
button is pressed.
TEST Button
Prints test receipt
with pump CAT data or
printer info depending
on which is being
received when button
is pressed.*
_____________________________________________________________________________________3
P/N 000-920921- Rev 0D 04/2015
2.2 Opening/Closing Printer Door
1. At the top of the printer, pull the front door handle down to open the printer
door as shown below.
2. Push the printer door up and close until a click is heard which locks the
door. The printer will then begin the test print.
Printer door closed position
Printer door open position
4____________________________________________________________________________________
P/N 000-920921- Rev 0D 04/2015
2.3 Loading Paper
Follow the instructions below and refer to the photos on the next page for
loading paper.
1. Unlock and open the bezel printer access door on the front of the dispenser.
2. Pull down the print door.
3. Remove old paper core.
4. Insert a paper roll with paper feeding from the top of the roll as shown in the
photos and pull out the paper.
5. Insert the paper in the paper inlet as shown and the paper will feed several
cm automatically.
6. Push up the printer door until a click is heard.
7. Close and lock bezel printer access door.
_____________________________________________________________________________________5
P/N 000-920921- Rev 0D 04/2015
LOADING PAPER
Bezel Printer Door Lock
6____________________________________________________________________________________
P/N 000-920921- Rev 0D 04/2015
Ce manuel convient aux modèles suivants
1
Table des matières
