Waters Magnet+ Manuel utilisateur

USER MANUAL

Magnet+

Magnets can aect pacemakers

The magnetic eld near the magnets can aect pacemakers,

ICDs and other implanted medical devices.

Many of these devices are designed to deactivate in a

magnetic eld. Care must be taken to avoid inadvertently

deactivating such devices.

Safety instructions

• The device must always be completely switched o (cables

removed) before moving it.

• The device must be handled with caution as it contains

moving parts.

• The user must maintain a distance of at least 20cm from the

product (WiFi antenna) while it is being installed and operated.

• The device is intended for indoor use only.

• Device maintenance has to be done exclusively by an Andrew

Alliance representative.

• If the device is used in a manner not specied by the manufac-

turer, the protection provided by the device may be impaired.

• All the input/output ports are Safety Extra Low Voltage (SELV)

circuits. SELV circuits should only be connected to other SELV

circuits.

Power socket

Ethernet for

cable connection

LED indicator

Open hatch

from here

Built-in

computer

Built-in wireless

adapter

Labware holder

of other devices

About this manual

Read the user manual before using this device. Strictly follow usage and main-

tenance instructions provided in the manual. It is the user’s responsibility to

become familiar with all available information concerning the correct use, care

and limitations of these products. If you are uncertain about the correct use or

limitations of the products, contact Andrew Alliance service and support. The

manufacturer, the distributor and their respective owners, employees, agents and

representatives are not responsible or liable for errors or omissions.

Information in this User Manual is subject to change without notice and does

not represent a commitment on the part of Andrew Alliance. Andrew Alliance

assumes no responsibility for any inaccuracies that may be contained in this User

Manual. Andrew Alliance makes no commitment to update or keep current the

information in this User Manual, and reserves the right to make improvements

to this User Manual and/or to the products described in this User Manual, at any

time without notice.

If you nd information in this manual that is incorrect, misleading, or incomplete,

we would appreciate your comments and suggestions.

Product

overview

Power button

Getting started

Plug your Magnet+

into a power source.

Wait for the LED indicator to

turn blue and blink.

After a couple of mi-

nutes, the Magnet+ will

inform you when it is

in installation mode.

Connect your computer, tablet or smartphone to the Magnet+

Launch a web browser, type http://192.168.2.1

and follow the on-screen steps to continue installation.

A. Go to your Wi-Fi settings

and select the network named Magnet-5xx.4xxx.xxxxx

scan me

xxxx.xxxxx is the Magnet+ device serial number (you can nd it on top of your

device)

B. The LED indicator will stop blinking when it’s successfully connected.

Magnet-5xx.4xxx.xxxxx

If the Magnet+ doesn’t automatically

enter installation mode, press the power

button 5 times.

http://192.168.2.1

Before

you begin

If you do not have a OneLab account, please create one by going to:

https://onelab.andrewalliance.com/signup

The device will automatically start up.

Only use the provided AC/DC

power supply unit and cords.

Please note that the

installation page might

open automatically.

If you do not have access to a

Wi-Fi compatible device, please

refer to our online help:

help.andrewalliance.com

45 steps

1:46:37

No additional guidelines

Simultaneous activity

None

Stop vortexing

Next step

I've made a mistake...

Continue

AbortStep list

Experiment ongoing: Bead puriﬁcation protocol - 076

Wait for the beads to pellet…

01:20

Beads

pelleting

Magnet+ - 933.3939.XXX

Magnet+

Applying magnetic ﬁeld…

Sample

tube 293

Operations

Design your protocol

Execute experiment with

Magnet+

Start the experiment and let OneLab

control your device

Our drag-n-drop editor makes it easy to

design a precise and complete protocol

with all that you need to run your

experiment perfectly.

Create an Apply magnetic eld

action by clicking on this menu,

which is located in the left of the

screen.

Follow the visual instructions based on the

protocol being used and you will be guided

through your experiment.

Each step of the experiment will be recorded

and available in OneLab.

Actions

Apply magnetic

ﬁeld

OneLab will automatically select your

Magnet+ and allows you to use it with every

available experiment set-up, either manual,

semi-automated or fully automated operation.

Choose your desired experiment setup and

then prepare all the required materials.

Feel free to contact

the Andrew Alliance

support team Send us an email to

[email protected]

Chat with our support team

directly in OneLab

We reply within 1 business day

Technical data

Labware

compatible

Check the OneLab Domino Catalog

at andrewalliance.com/

domino-catalog

Relative humidity 80% at 37°C

Maximum

operating altitude

2000 m

Environment

temperature

operating range

+4 to +37°C

User interface Through OneLab software

Ingress protection IP20*

Dimensions

(W x L x H)

170 x 162 x 115 mm

(The specied dimensions are

subject to change according to the

labware)

Weight 1.65 kg

External power

supply

Input 100-240 VAC, 1.4 A

/ output 24 VDC, 5 A, 120 W

Power or

current rating

5 A

Overvoltage

category DC port

Cat I

Operating voltage 24 VDC

Network

connectivity

• Gigabit Ethernet

• Wi-Fi 2.4 GHz and 5 GHz

Pollution degree

of the intended

environment

Pollution degree 2

Cleaning Only with a wet tissue or isopro-

panol

Warranty 1 year

Certication CE, FCC, RoHS, WEEE

1. Place your connected

devices as indicated by

OneLab.

2. Open the hatches.

3. Plug the power cables

into your devices power socket.

4. Pass the cables in front of devices and then

insert them into the dedicated path.

5. Close the hatches.

Multiple connected devices

installation

Operating device

Power on

Power o

When the device is in standby mode

(plugged to power source but turned

o), press the power button to turn

on the device.

Note: The device will automatically

start up when you plug it to a power

source.

When the device is in its idle state

(no experiment running), press the

power button for 5 seconds to turn

o the device.

*Avoid spilling liquid on the device.

Unit end of life

When a unit reaches the end of its useful life, contact Andrew Alliance for

directions and information on the end-of-life policy.

This is in accordance with the European Union Directive 2002/96/EC on

Waste Electrical and Electronic Equipment (WEEE).

Certications

Electrical safety

EMC

RADIO

FCC

RoHS

I. IEC 61010-1: 2010

II. IEC 61010-1/A1: 2016

III. UL 61010-1:2012

IV. CAN/CSA 22.2#61010-1-12

I. EN 61326-1: 2013

II. EN 301 489-1 V2.2.0

III. EN 301 489-17 V3.1.0

I. EN 300 328 Ver 2.1.1

II. EN 301 893 V2.1.1

I. FCC 47 CFR part 15 subpart B section 15.107 (b) and section 15.109 (b and g)

Class A all over other device tested per ANSI C63.4 (Ed. 2014) procedures

II. This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired opera-

tion.

RoHS 3 (EU) 2015/863

Waters Corp

34 Maple Street

Milford, MA 01757

USA

Phone: +1-508-478-2000

Andrew Alliance S.A.

(Headquarters)

Chemin Grenet 21

1214 Vernier (Geneve)

Switzerland

Phone: +41 22 518 0357

[email protected]

Part number: 518.005.2 | 2021 © Andrew Alliance - A Waters Company.

Table des matières

Autres manuels Waters Équipement de laboratoire

Waters

Waters APGC Manuel du propriétaire

Waters

Waters Vion IMS QTof Manuel d'utilisation

Waters

Waters Xevo G2 QTof Manuel d'utilisation

Waters

Waters TRIZAIC UPLC Manuel de la liste des pièces

Waters

Waters ACQUITY UPLC M-Class Manuel de la liste des pièces

Waters

Waters Xevo TQD Manuel utilisateur

Waters

Waters 2707 Manuel

Waters

Waters ACQUITY Arc System Manuel de la liste des pièces

Waters

Waters ACQUITY UPLC I-Class IVD Manuel de la liste des pièces

Waters

Waters Xevo TQD Manuel d'utilisation

Waters

Waters ACQUITY Isocratic Solvent Manager Manuel d'utilisation

Waters

Waters Quattro Premier XE Manuel

Waters

Waters ACQUITY UPC2 Manuel de la liste des pièces

Waters

Waters SYNAPT G2 Manuel utilisateur

Waters

Waters ACQUITY UPLC Manuel d'utilisation

Waters

Waters Prep Series Manuel du produit

Waters

Waters Prep 150 LC System Manuel utilisateur

Waters

Waters Anionic Polar Pesticide Column Mode d’emploi

Waters

Waters Xevo TQ MS Manuel d'utilisation

Waters

Waters GCT Premier Manuel

Waters

Waters Andrew+ Manuel utilisateur

Waters

Waters ACQUITY APC XT 45 Mode d’emploi

Waters

Waters Otto SPEcialist PPM Manuel d'utilisation

Waters

Waters Positive Pressure-96 Manuel

Manuels Équipement de laboratoire populaires d'autres marques

Qiagen

Qiagen DML 3000 Manuel utilisateur

Queensgate

Queensgate NANOSCAN OP400 Manuel de programmation

Conviron

Conviron GEN1000-GE Manuel utilisateur

Parr Instrument

Parr Instrument 4560 Mode d’emploi

IKA

IKA IC control Manuel utilisateur

Integra

Integra DOSE IT Manuel utilisateur

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuel utilisateur

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuel utilisateur

NI PXI-5422 Manuel

Collomix

Collomix Aqix Manuel utilisateur

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur

Ocean Insight

Ocean Insight FLAME-NIR+ Manuel utilisateur

Parker

Parker ALIGN-MG-NA Manuel utilisateur

BD 644787 Manuel utilisateur

DENTAURUM

DENTAURUM Compact Megaplus Manuel utilisateur

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuel utilisateur

VWR

VWR SAS Super IAQ Manuel utilisateur

illumina

illumina MiSeqDx Manuel utilisateur