Watermark JE Series Manuel utilisateur
INSTALLATION INSTRUCTIONS
Boiling Billy JE, JR Series
DO NOT PLUG IN OR TURN ON
POWER
1. Fit tap and shank on the outlet connection
provided.
2. Mount unit on the wall using fixing points on
the back of the unit. It is advisable to
position the tap outlet over a drain board so
that in the event of a leaking tap the water
can be disposed via the sink.
3. Connect cold water supply to the inlet
(12mm) through a stop tap in the supply
line. (stop tap to be provided by the
installer)(. We recommend the fitting of a
350kpa PLV.
4. Connect overflow pipe to waste or any other
area where water can be disposed in a safe
manner.( Tundish should be fitted)
5. * Plug unit into 10 amp power outlet.
6. Turn ‘on’ water supply to the unit and ‘open’
the outlet tap.
7. Wait until the water flows out of the tap.
8. When the water flows out of the tap please
switch on the power.
*3.0kw element requires a 15amp power outlet.
INSTALLATION INSTRUCTIONS
JE SERIES
INSTALLATION INSTRUCTIONS
JR SERIES
INSTALLATION INSTRUCTIONS
Boiling Billy JE, JR Series
DO NOT PLUG IN OR TURN ON
POWER
•ALL UNITS MUST BE FITTED WITH A
WATERMARKED WATER FILTER OR VOID
WARRANTY .
•ONLY TEFLON TAPE TO BE USED WHERE
NECESSARY.
•UNDER NO CIRCUMSTANCES IS
PLUMBERS PASTE TO BE USED.
To Plumber/User
DEPENDING ON WATER CONDITIONS, ADDITIONAL PRE-
FILTERS SHOULD BE FITTED.
(CONTACT THE MANUFACTURER)
DO NOT connect to hot water line-to do so will VOID warranty.
AFTER POWER IS ON- allow 30 minutes before using.
Please leave these instructions with the owner.
DO NO MEGGER
Contact Us
1/33 Cedar Parade Moolap,
Victoria
Phone: (03) 52487072
Email: sales@boiling-billy.com
Web: www.boiling-billy.com
Web: www.boiling-billy.com
LIC WM- 0359
WIFFEN PRODUCTS PTY LTD
A.C.N 073 810 616 A.B.N 95 073 810 616
Issue April 2020
Above Sink Boiling Billy
Instructions
IMPORTANT PLEASE READ
WIFFEN PRODUCTS PTY LTD
Boiling Billy
This appliance is not intended for use by young children or infirm
persons unless they have been adequately supervised by a
responsible person to ensure that they can use the appliance
safely.
. Children being supervised not to play with the appliance
∙This appliance is intended to be used in household and
similar working environments e.g. staff kitchen areas in
shops, offices, farmhouses, and other working
environments.
. By clients in hotels, motels, bed, and breakfast type
environments∙ ∙Ensure the power cable and power lead do not
come into contact with liquids
∙Misuse of this product may cause harm or serious injury
To Our Valued Customer
A special Thank you for choosing to purchase and install our
ABOVE SINK BOILING BILLY
INSTALLATION AND MAINTENANCE INSTRUCTION
For the above sink: Boiling Billy JE, JR series.
IMPORTANT PLEASE READ
“The Above sink Boiling Billy” dispenses boiling water
Please treat with care
If tundish is to be used, it must be placed above the sink in the
open.
An authorised plumber must install units- unit must be connected in
accordance with AS/NZS 3500.1 or AS/NZS 3500.4
POWER MUST BE OFF UNTIL INSTALLATION IS COMPLETED
*The unit is fitted with a computerized element and boil dry protection. The
computer is set at 97degrees C, + -1 degree.
*Altitude will alter temperature (refer back to manufacturer)
•This unit must be fitted with a filter we recommend changing the
cartridge every 6 months.
•The manufacturer recommends the cleaning and service of the unit
every 12 months.
IF SUPPLIED CORD IS DAMAGED IT
MUST BE REPLACED BY AN AUTHORISED SERVICE AGENT
DO NOT SWITCH POWER ON UNTIL WATER RUNS OUT OF TAP.
TROUBLESHOOTING
Action only to be performed by a qualified person.
SYMPTON
CAUSES
ACTION
Water
overflowing
Water level to high
Check and set water level to
indicated level 20mm below
overflow pipe. Remove ball
valve insert. Clean and
reinstall and adjust ball
valve arm if necessary.
Remove ball valve float and
check to ensure that there is
not water in it Replace if
necessary.
Continuous
boiling
Ball Valve defective
Faulty element
Ensure ball valve closes
off(does not leak)
Replace if necessary
Replace Element
Water not hot
Power not on
Element faulty
Check if power is on
Replace element
No water
Water has been
turned off
Blocked ball valve
Blocked filter
Units fitted with mini
ball valve-located
inside case at base
inlet side
Turn on water
Remove ball valve and
clean out hole or replace
ball valve
Change filter cartridge
Fully open mini ball valve
and re adjust water flow
as instructions on side of
case.
Maximum inlet pressure 820kpa
JE & JR units must be fitted with an approved 350kpa
pressure limiting valve.
Minimum inlet pressure 200kpa.
If a lower pressure is encountered refer to manufacturer.
Ce manuel convient aux modèles suivants
1
Autres manuels Watermark Système d'eau
Manuels Système d'eau populaires d'autres marques
Spirotech
Spirotech SPIROVENT SUPERIOR S250 Manuel utilisateur
Culligan
Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manuel utilisateur
A.O. Smith
A.O. Smith Dura-Max AJH - 1000A - P Manuel utilisateur
Microline
Microline T.F.C.-4 Manuel
Eureka Forbes
Eureka Forbes Aquaguard Select Manuel utilisateur
Cetetherm
Cetetherm AquaEfficiency Manuel utilisateur
