WAGO I/O SYSTEM 750 Manuel utilisateur

Fieldbus Independent

I/O Modules

Bluetooth®RF Transceiver

750-644

Quick Start

Version 1.0.1

2 • General

WAGO-I/O-SYSTEM 750

I/O Modules

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the correctness and com-

pleteness of this documentation. However, as errors can never be fully ex-

cluded, we would appreciate any information or ideas at any time.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally trademark or patent protected.

Important Comments • 3

Legal Principles

WAGO-I/O-SYSTEM 750

I/O Modules

Content

1Important Comments ................................................................................. 4

1.1 Legal Principles........................................................................................4

1.1.1 Copyright............................................................................................. 4

1.1.2 Personnel Qualification ....................................................................... 4

1.1.3 Intended Use........................................................................................ 4

1.2 Symbols....................................................................................................5

1.3 Number Notation......................................................................................5

1.4 Safety Notes ............................................................................................. 6

1.5 Scope ........................................................................................................6

2Quick Start................................................................................................... 7

2.1 Network Structure .................................................................................... 7

2.2 Starting up the Bluetooth®Modules.........................................................9

2.2.1 Configuration of the Bluetooth®Slave Using "Net Forming".............9

2.2.2 Configuration of the Bluetooth®Master Using "Net Forming" ........13

2.2.3 Process Data Allocation.....................................................................15

2.3 Testing the Process Data Exchange........................................................16

4• Important Comments

Legal Principles

WAGO-I/O-SYSTEM 750

I/O Modules

1 Important Comments

To ensure fast installation and start-up of the units described in this manual,

we strongly recommend that the following information and explanations are

read carefully and followed.

1.1 Legal Principles

1.1.1 Copyright

This manual is copyrighted, together with all figures and illustrations con-

tained therein. Any use of this manual which infringes the copyright provi-

sions stipulated herein, is not permitted. Reproduction, translation and elec-

tronic and photo-technical archiving and amendments require the written con-

sent of WAGO Kontakttechnik GmbH & Co. KG. Non-observance will entail

the right of claims for damages.

WAGO Kontakttechnik GmbH & Co. KG reserves the right to perform modi-

fications allowed by technical progress. In case of grant of a patent or legal

protection of utility patents all rights are reserved by WAGO Kontakttechnik

GmbH & Co. KG. Products of other manufacturers are always named without

referring to patent rights. The existence of such rights can therefore not be

ruled out.

1.1.2 Personnel Qualification

The use of the product detailed in this manual is exclusively geared to special-

ists having qualifications in PLC programming, electrical specialists or per-

sons instructed by electrical specialists who are also familiar with the valid

standards. WAGO Kontakttechnik GmbH & Co. KG declines all liability re-

sulting from improper action and damage to WAGO products and third party

products due to non-observance of the information contained in this manual.

1.1.3 Intended Use

For each individual application, the components supplied are to work with a

dedicated hardware and software configuration. Modifications are only per-

mitted within the framework of the possibilities documented in the manuals.

All other changes to the hardware and/or software and the non-conforming use

of the components entail the exclusion of liability on part of WAGO Kon-

takttechnik GmbH & Co. KG.

Please direct any requirements pertaining to a modified and/or new hardware

or software configuration directly to WAGO Kontakttechnik GmbH & Co.

KG.

Important Comments • 5

Symbols

WAGO-I/O-SYSTEM 750

I/O Modules

1.2 Symbols

Danger

Always abide by this information to protect persons from injury.

Warning

Always abide by this information to prevent damage to the device.

Attention

Marginal conditions must always be observed to ensure smooth operation.

ESD (Electrostatic Discharge)

Warning of damage to the components by electrostatic discharge. Observe

precautionary measures for handling components at risk.

Note

Routines or advice for efficient use of the device and software optimization.

Additional Information

References for additional literature, manuals, data sheets and web pages.

1.3 Number Notation

Number Code Example Note

Decimal 100 normal notation

Hexadecimal 0x64 C notation

Binary '100'

'0110.0100'

within inverted commas,

nibble separated with dots

6• Important Comments

Safety Notes

WAGO-I/O-SYSTEM 750

I/O Modules

1.4 Safety Notes

Warning

Switch-off the system prior to working on bus modules!

In the event of deformed contacts, the module in question is to be replaced, as

its functionality can no longer be ensured on a long-term basis.

The components are not resistant against materials having seeping and insu-

lating properties. Members of this group include: aerosols, silicones, triglyc-

erides (found in some hand creams).

If it cannot determined that these materials appear in the component envi-

ronment, then additional measures must be taken:

- install of the components in an appropriate enclosure

- handle components only with clean tools and materials.

Attention

Soiled contacts may only be cleaned with ethyl alcohol and leather cloths.

This helps ensure compliance with ESD information.

Do not use any contact spray. The spray may impair the functioning of the

contact area.

The WAGO-I/O-SYSTEM 750 and its components are an open system. As

such, the system and its components must be installed in appropriate hous-

ings, cabinets, enclosures or in electrical operation rooms. Access must only

be provided via key or tool to authorized, qualified personnel.

The relevant valid and applicable standards and guidelines concerning the

installation of switch boxes are to be observed.

ESD (Electrostatic Discharge)

The modules are equipped with electronic components that may be destroyed

by electrostatic discharge. When handling the modules, ensure that the envi-

ronment (persons, workplace and packing) is well grounded. Avoid touching

conductive components; e.g., gold contacts.

1.5 Scope

These quick start instructions describe the first steps for configuring two

Bluetooth®RF Transceivers 750-644. The contents of the instructions are only

valid in connection with the manual "Bluetooth® RF Transceiver 750-644" and

the manual for the software WAGO-I/O-CHECK.

You will find these documents on the CD "AUTOMATION Tools & Docs"

(item no.: 0888-0412) and online at http://www.wago.com.

Quick Start • 7

Network Structure

WAGO-I/O-SYSTEM 750

I/O Modules

2 Quick Start

These quick start instructions explain, by means of an example, how to start-

up and configure the Bluetooth® RF-Transceiver 750-644 (Bluetooth®module)

via WAGO-I/O-CHECK.

The instructions demonstrate how to start the module up with minimal con-

figuration, and therefore do not describe the entire range of functions. The ob-

jective of these instructions is to configure a simple peer-to-peer communica-

tion between two Bluetooth®modules. One module will function as a master,

the other as a slave.

2.1 Network Structure

1. Construct two identical bus nodes as shown in Figure 1.

• 750-841 Ethernet Controller

• 750-644 Bluetooth® RF Transceiver

• 750-600 End Module

2. Connect one of the controllers to a free serial port of your PC using a

WAGO communication cable (750-920).

3. Connect the second controller in the same manner to another PC serial

port.

Attention

Do not form a fieldbus connection (e.g., by using an ETHERNET cable);

otherwise, access to the process data within WAGO-I/O-CHECK is not pos-

sible.

4. Connect both nodes on the system and field sides with a 24-volt power

supply.

5. Switch the power supply on.

Additional information

Each serial PC port is operated by its own WAGO-I/O-CHECK software.

Depending on port availability, use one or two PCs for configuring the mod-

ules.

If you are using one PC with two ports, the WAGO-I/O-CHECK software

can be started several times. You can select the proper COM ports using the

"F8" key on your keyboard. If using only one port or one WAGO-I/O-

CHECK, the configuration of master and slaves is rather time-consuming.

8• Quick Start

Network Structure

WAGO-I/O-SYSTEM 750

I/O Modules

Figure 1: Hardware configuration g064461e

Quick Start • 9

Starting up the Bluetooth® Modules

WAGO-I/O-SYSTEM 750

I/O Modules

2.2 Starting up the Bluetooth®Modules

1. Determine which Bluetooth® module will function as the master and which

module will function as the slave.

2. Write down the MAC address of the slave: 0 0 : 0 6 : C 6 : _ _ : _ _ : _ _

Write down the MAC address of the master: 00: 0 6 : C 6 : _ _ : _ _ : _ _

2.2.1 Configuration of the Bluetooth®Slave Using "Net Forming"

1. Start the WAGO-I/O-CHECK software (Version 3 or later).

2. Click on the [Identify] button.

Your node configuration is graphically displayed (see Figure 2).

Figure 2: Identify your node configuration g064462e

3. Click with the right mouse button on the Bluetooth® module that you

would like to configure as a slave.

10 • Quick Start

Starting up the Bluetooth® Modules

WAGO-I/O-SYSTEM 750

I/O Modules

4. In the module's context menu, choose Settings. This opens the Bluetooth®-

specific parameterization dialog of the module (see Figure 3).

Figure 3: Bluetooth®-specific parameter area g064418e

Attention

For the following, the Bluetooth® module's must remain intact; i.e., no con-

figuration attempts have been attempted. If this is not the case, click on the

[Default] button to restore the module to factory default settings.

5. Click on [Data Frame] in the toolbar.

6. Enter (if not already set) a process image size of 48 bytes and a mailbox

size of 12 bytes (see Figure 4).

Figure 4: Data structure g064444e

7. Click on the [Read] button in the toolbar to update the view of the con-

figuration in the module.

Autres manuels pour I/O SYSTEM 750

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels WAGO Système d'E/S

WAGO

WAGO I/O-SYSTEM 750 Manuel utilisateur

WAGO

WAGO I/O System 750 750-622 Manuel utilisateur

WAGO

WAGO 750-626/040-000 Manuel utilisateur

WAGO

WAGO I/O System 750 Series Manuel utilisateur

WAGO

WAGO 765-4203/0100-0000 Manuel utilisateur

WAGO

WAGO 750-1423 Manuel utilisateur

WAGO

WAGO WAGO-I/O-SYSTEM 752 Manuel utilisateur

WAGO

WAGO 765-1505/100-000 Manuel utilisateur

WAGO

WAGO WAGO-I/O-SYSTEM 750 XTR Series Manuel utilisateur

WAGO

WAGO 750-560 Manuel utilisateur

WAGO

WAGO WAGO-I/O-SYSTEM750 Series Manuel utilisateur

WAGO

WAGO I/O-SYSTEM 750 Manuel utilisateur

WAGO

WAGO I/O-SYSTEM 750 Manuel utilisateur

WAGO

WAGO 750-464 Manuel utilisateur

WAGO

WAGO I/O-SYSTEM 750-517 Manuel utilisateur

WAGO

WAGO I/O-SYSTEM 750 753-501 Manuel utilisateur

WAGO

WAGO I/O-SYSTEM 750 Manuel utilisateur

WAGO

WAGO WAGO-I/O-SYSTEM 750 XTR Series Manuel utilisateur

WAGO

WAGO I/O-SYSTEM 750-1425 Manuel utilisateur

WAGO

WAGO 750 Series Manuel utilisateur

WAGO

WAGO 767-6402 Manuel utilisateur

WAGO

WAGO 750-626 Manuel utilisateur

WAGO

WAGO 750 Series Manuel utilisateur

WAGO

WAGO I/O-SYSTEM 750 Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur

Contec

Contec PIO-16L(PCI)H Manuel utilisateur