WAGO 750-556 Manuel utilisateur

Fieldbus Independent

I/O Modules

2 AO DC ±10 V

750-556

Manual

Version 1.0.2

ii • General

WAGO-I/O-SYSTEM 750

I/O Modules

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: + 49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the correctness and com-

pleteness of this documentation. However, as errors can never be fully ex-

cluded, we would appreciate any information or ideas at any time.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the tra-

demarks of companies used and/or mentioned in the present manual are gener-

ally trademark or patent protected.

Content • iii

WAGO-I/O-SYSTEM 750

I/O Modules

Content

1Important Comments ................................................................................. 4

1.1 Legal Principles........................................................................................4

1.1.1 Copyright............................................................................................. 4

1.1.2 Personnel Qualification .......................................................................4

1.1.3 Intended Use ........................................................................................4

1.2 Symbols....................................................................................................5

1.3 Number Notation......................................................................................5

1.4 Safety Notes .............................................................................................6

1.5 Scope ........................................................................................................6

2I/O Modules ................................................................................................. 7

2.1 Analog Output Modules ...........................................................................7

2.1.1 750-556 [2 AO DC ±10 V]..................................................................7

2.1.1.1 View................................................................................................7

2.1.1.2 Variations........................................................................................7

2.1.1.3 Description......................................................................................8

2.1.1.4 Display Elements ............................................................................9

2.1.1.5 Schematic Diagram.........................................................................9

2.1.1.6 Technical Data ..............................................................................10

2.1.1.7 Process Image ...............................................................................11

2.1.1.7.1 Standard Format .......................................................................12

2.1.1.7.2 Special Formats........................................................................12

4 • Important Comments

Legal Principles

WAGO-I/O-SYSTEM 750

I/O Modules

1 Important Comments

To ensure fast installation and start-up of the units described in this manual,

we strongly recommend that the following information and explanations are

carefully read and abided by.

1.1 Legal Principles

1.1.1 Copyright

This manual is copyrighted, together with all figures and illustrations con-

tained therein. Any use of this manual which infringes the copyright provi-

sions stipulated herein, is not permitted. Reproduction, translation and elec-

tronic and photo-technical archiving and amendments require the written con-

sent of WAGO Kontakttechnik GmbH & Co. KG. Non-observance will entail

the right of claims for damages.

WAGO Kontakttechnik GmbH & Co. KG reserves the right to perform modi-

fications allowed by technical progress. In case of grant of a patent or legal

protection of utility patents all rights are reserved by WAGO Kontakttechnik

GmbH & Co. KG. Products of other manufacturers are always named without

referring to patent rights. The existence of such rights can therefore not be

ruled out.

1.1.2 Personnel Qualification

The use of the product detailed in this manual is exclusively geared to special-

ists having qualifications in PLC programming, electrical specialists or per-

sons instructed by electrical specialists who are also familiar with the valid

standards. WAGO Kontakttechnik GmbH & Co. KG declines all liability re-

sulting from improper action and damage to WAGO products and third party

products due to non-observance of the information contained in this manual.

1.1.3 Intended Use

For each individual application, the components supplied are to work with a

dedicated hardware and software configuration. Modifications are only per-

mitted within the framework of the possibilities documented in the manuals.

All other changes to the hardware and/or software and the non-conforming use

of the components entail the exclusion of liability on part of WAGO Kon-

takttechnik GmbH & Co. KG.

Please direct any requirements pertaining to a modified and/or new hardware

or software configuration directly to WAGO Kontakttechnik GmbH & Co.

KG.

Important Comments • 5

Symbols

WAGO-I/O-SYSTEM 750

I/O Modules

1.2 Symbols

Danger

Always abide by this information to protect persons from injury.

Warning

Always abide by this information to prevent damage to the device.

Attention

Marginal conditions must always be observed to ensure smooth operation.

ESD (Electrostatic Discharge)

Warning of damage to the components by electrostatic discharge. Observe

the precautionary measure for handling components at risk.

Note

Routines or advice for efficient use of the device and software optimization.

More information

References on additional literature, manuals, data sheets and INTERNET

pages

1.3 Number Notation

Number Code Example Note

Decimal 100 normal notation

Hexadecimal 0x64 C notation

Binary '100'

'0110.0100'

Within ',

Nibble separated with dots

6 • Important Comments

Safety Notes

WAGO-I/O-SYSTEM 750

I/O Modules

1.4 Safety Notes

Warning

Switch off the system prior to working on bus modules!

In the event of deformed contacts, the module in question is to be replaced, as

its functionality can no longer be ensured on a long-term basis.

The components are not resistant against materials having seeping and insu-

lating properties. Belonging to this group of materials is: e.g. aerosols, sili-

cones, triglycerides (found in some hand creams).

If it cannot be ruled out that these materials appear in the component envi-

ronment, then additional measures are to be taken:

- installation of the components into an appropriate enclosure

- handling of the components only with clean tools and materials.

Attention

Cleaning of soiled contacts may only be done with ethyl alcohol and leather

cloths. Thereby, the ESD information is to be regarded.

Do not use any contact spray. The spray may impair the functioning of the

contact area.

The WAGO-I/O-SYSTEM 750 and its components are an open system. It

must only be assembled in housings, cabinets or in electrical operation

rooms. Access must only be given via a key or tool to authorized qualified

personnel.

The relevant valid and applicable standards and guidelines concerning the

installation of switch boxes are to be observed.

ESD (Electrostatic Discharge)

The modules are equipped with electronic components that may be destroyed

by electrostatic discharge. When handling the modules, ensure that the envi-

ronment (persons, workplace and packing) is well grounded. Avoid touching

conductive components, e.g. gold contacts.

1.5 Scope

This manual describes the Analog Output Module 750-556

2 AO DC ±10 V of the modular WAGO-I/O-SYSTEM 750.

Handling, assembly and start-up are described in the manual of the Fieldbus

Coupler. Therefore this documentation is valid only in the connection with the

appropriate manual.

750-556 [2 AO DC ±10 V] • 7

View

WAGO-I/O-SYSTEM 750

I/O Modules

2 I/O Modules

2.1 Analog Output Modules

2.1.1 750-556 [2 AO DC ±10 V]

2-Channel Analog Output Module ±10 V

2.1.1.1 View

A1 A2

13 14

750-556

AO 2

Data contacts

Function AO 2

Function AO 1

AO 1

Shield

(screen)

Shield

(screen)

Common

(ground)

Common

(ground)

Fig. 2.1.1-1: 2-Channel Analog Output Module 750-556 g055600e

2.1.1.2 Variations

Item-No.: Designation Description

750-556 2 AO (±10 V) 2-Channel Analog Output Module , ±10 V

750-556/000-200 2 AO (±10 V)

with Siemens

(S5-FB 251)

2-Channel Analog Output Module , ±10 V,

adapted data format for S5-control systems

with the use of function block FB 251

8 • 750-556 [2 AO DC ±10 V]

Description

WAGO-I/O-SYSTEM 750

I/O Modules

2.1.1.3 Description

The analog output module 750-556 and its variation create a standardized sig-

nal of ±10 V.

The module has two short circuit protected output channels and enables the di-

rect wiring of two 2-conductor actuators to AO 1 and ground or AO 2 and

ground. The signals are transmitted via AO 1 or AO 2.

The channels have a common ground and a shield (screen) (S). The shield

(screen) is directly connected to the DIN rail. A capacitive connection is made

automatically when snapped onto the DIN rail.

The input signal is electrically isolated and will be transmitted with a resolu-

tion of 12 bits.

The operational readiness and the trouble-free internal data bus communica-

tion of the channels are indicated via a function LED.

Any configuration of the output modules is possible when designing the field-

bus node. Grouping of module types is not necessary.

The voltage supply is done via the internal system voltage.

Attention

This module has no power contacts. For field supply to downstream I/O mod-

ules, a supply module will be needed.

The analog output module 750-556 and its variations can be used with all cou-

plers/controllers of the WAGO-I/O-SYSTEM 750 (except for the economy

types 750-320, -323, -324 and -327).

750-556 [2 AO DC ±10 V] • 9

Display Elements

WAGO-I/O-SYSTEM 750

I/O Modules

2.1.1.4 Display Elements

LED Channel Designation State Function

off

No operational readiness or the

internal data bus communication

is interrupted

green 1 Function

AO 1

on Operational readiness and trou-

ble-free operational readiness

off

No operational readiness or the

internal data bus communication

is interrupted

13 14

Fig. 2.1.1-2: Display

Elements g055202x C

green 2 Function

AO 2

on Operational readiness and trou-

ble-free operational readiness

2.1.1.5 Schematic Diagram

Shield

(screen)

AO 1 AO 2 AO

10nF

270pF

DLogic

Function

Shield

(screen)

Common

(ground)

Common

(ground)

750-556

Fig. 2.1.1-3: 2-Channel Analog Output Module 750-556 g055601e

10 • 750-556 [2 AO DC ±10 V]

Technical Data

WAGO-I/O-SYSTEM 750

I/O Modules

2.1.1.6 Technical Data

Module Specific Data

Number of outputs 2

Current consumption typ. (internal) 65 mA

Voltage supply via system voltage DC/DC

Signal voltage ±10 V

Load impedance > 5 kΩ

Linearity ±10 mV

Resolution 12 Bit

Conversion time approx. 2 ms

Output filter settle time typ. 300 µs

Measuring error 25°C <±0.1 % of the full scale value

Temperature coefficient <±0.01 % /K of the full scale value

Isolation 500 V (Field/System)

Bit width 2 x 16 bits data

2 x 8 bits control/status(option)

Dimensions (mm) W x H x L 12 x 64* x 100

* from upper edge of 35 DIN rail

Weight ca. 55 g

Standards and Regulations (cf. Chapter 2.2 of the Coupler/Controller Manual)

EMC-Immunity to interference (CE) acc. to EN 50082-2 (96)

EMC-Emission of interference (CE) acc. to EN 50081-1 (93)

EMC-Immunity to interference

(Ship building)

acc. to Germanischer Lloyd (97)

EMC-Emission of interference

(Ship building)

acc. to Germanischer Lloyd (97)

Ce manuel convient aux modèles suivants

Autres manuels WAGO Système d'E/S

WAGO

WAGO I/O SYSTEM 750 Manuel de service

WAGO

WAGO 879-3001 (4PU) Guide produit

WAGO

WAGO 750-440 Manuel utilisateur

WAGO

WAGO Automation WAGO-I/O-SYSTEM 750 Manuel utilisateur

WAGO

WAGO 753-482 Manuel utilisateur

WAGO

WAGO WAGO-I/O-SYSTEM 750 XTR Series Manuel utilisateur

WAGO

WAGO I/O SYSTEM 750 Manuel utilisateur

WAGO

WAGO LONWORKS 750-319 Manuel utilisateur

WAGO

WAGO 8FDI 24V PROFIsafe 750-662/000-004 Manuel utilisateur

WAGO

WAGO 750 Series Manuel utilisateur

WAGO

WAGO 750-370 Manuel utilisateur

WAGO

WAGO I/O-SYSTEM 750 Manuel utilisateur

WAGO

WAGO 767-6402 Manuel utilisateur

WAGO

WAGO 750-560 Manuel utilisateur

WAGO

WAGO I/O SYSTEM 750 Manuel utilisateur

WAGO

WAGO I/O System 750 Series Manuel utilisateur

WAGO

WAGO 750 Series Manuel utilisateur

WAGO

WAGO 750-496 Manuel utilisateur

WAGO

WAGO 750 Series Manuel utilisateur

WAGO

WAGO WAGO-I/O-SYSTEM 750 Series Manuel utilisateur

WAGO

WAGO WAGO-I/O-SYSTEM 750 Series Manuel utilisateur

WAGO

WAGO 750 Series Manuel utilisateur

WAGO

WAGO 750 Series Manuel utilisateur

WAGO

WAGO 750-370 Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur

Contec

Contec PIO-16L(PCI)H Manuel utilisateur