WAGNER W 95 Manuel utilisateur

W 95

D/GB/F/NL

2 JAHRE

GARANTIE



2 YEARS

GUARANTEE

2 ANS DE

GARANTIE

# 0050342

# 0209058

Read the operating instructions carefully before using the tool and observe the

safety instructions. Keep the operating

instructions in a safe place.

General Safety Instructions

Caution! Read all the instructions. Non-observance of the instructions below can

cause electric shock, fire and or serious personal injuries. The term

"power tool" used below covers both mains-operated power tools (with

mains lead) and accumulator-operated power tools (without mains

lead).

KEEP THESE INSTRUCTIONS IN A SAFE PLACE:

1. Workplace

a) Keep your workplace clean and tidy. Untidiness and unlit working areas can

lead to accidents.

b) Never use the tool in hazardous areas that contain flammable liquids,

gases or dusts. Power tools generate sparks that can ignite the dust or

vapors.

c) Keep children and other persons away when using the power tool. You

can lose control of the tool if you are distracted.

2. Electrical Safety

a) The tool plug must fit into the socket. The plug may not be modified in

any form. Do not use adaptor plugs together with protective-earthed

tools. Unmodified plugs and suitable sockets reduce the risk of an electric

shock.

b) Avoid physical contact with earthed surfaces such as pipes, heating

elements, stoves and refrigerators. The risk through electric shock increases

if your body is earthed.

c) Keep the equipment away from rain and moisture. The risk of an electric

shock increases if water penetrates electrical equipment.

d) Do not misuse the mains lead by carrying the tool by the lead, hanging it

from the lead or by pulling on the lead to remove the plug. Keep the lead

away from heat, oil, sharp edges or moving tool parts. Damaged or twisted

leads increase the risk of an electric shock.

W 95

e) If you work outdoors, use only extension leads that are approved for

outdoor use. The use of an extension lead that is suitable for outdoors reduces

the risk of an electric shock.

3. Safety of Persons

a) Be attentive. Pay attention to what you are doing and work sensibly with a

power tool. Do not use the tool if you are tired or under the influence of

drugs, alcohol or medication. Just a moment of inattentiveness while using

the tool can lead to serious injuries.

b) Wear personal safety equipment and always wear safety goggles Wearing

personal protective equipment, such as dust mask, non-slip safety shoes,

safety helm or ear protection, depending on the type of power tools, reduces

the risk of injury.

c) Avoid accidental starting-up. Ensure that the switch is in the "OFF"

position before inserting the plug into the socket. Accidents can occur if

you carry the power tool while your finger is on the switch or if you connect the

power tool to the power supply which it is on.

d) Remove setting tools or wrenches before switching on the power tool. A

tool or wrench that is in a rotating tool part can lead to injuries.

e) Do not overestimate your abilities. Ensure that you are standing securely

and have your balance at all times. This ensures that you can control the tool

better in unexpected situations.

f) Wear suitable clothing. Do not wear wide clothing or jewelry. Keep your

hair, clothes and gloves away from moving parts. Loose clothing, jewelry or

long hair can be caught in moving parts.

g) If dust extraction or collection devices can be mounted, ensure that these

are connected and are being used properly. Using these devices reduces

the danger caused by dust.

4. Careful Handling and Use of Power Tools

a) Do not overload the tool. Use the power tool designed for the work that

you are doing. You work better and safer in the specified performance range if

you use the suitable power tool.

b) Do not use power tools whose switch is defective. A power tool that cannot

be switched on or off is dangerous and has to be repaired.

W 95

c) Remove the plug from the socket before carrying out tool settings,

changing accessories or putting the tool away. This precautionary measure

prevents unintentional starting of the tool.

d) Store unused power tools so that they are inaccessible to children. Do

not let persons use the tool who are not familiar with it or who have not

read these instructions. Power tools are dangerous when they are used by

inexperienced persons.

e) Take proper care of your tools. Check whether the moving parts function

trouble-free and do not jam, whether parts are broken or damaged so that

the tool function is impaired. Have damaged parts repaired before using

the tool. Many accidents have their origin in power tools that have been

maintained badly.

f) Use the power tool, accessories, insert tools, etc. in accordance with

these instructions and in a fashion specified for this special tool type.

Take the working conditions and the activity to be carried out into

consideration. The use of power tools for purposes other than the intended

ones can lead to dangerous situations.

5. Service

a) Have your tool repaired only by qualified specialist personnel and only

with original spare parts. This ensures that the tool safety is maintained.

Safety Instructions for Spray Guns

●Spray materials emerge from nozzle tips under high pressure.

Attention! Danger of injection - Never point the spray stream towards

human beings or animals.

●The spray gun is to be used only for paints and solvents with a 21° C (32° in UK)

flashpoint or higher (See information on the material tin. Hazard class A II and A III

permitted).

●The spray gun is not to be used in work places covered by Ex-protection

regulations.

●To avoid the hazard of explosion when spraying, provide for effective natural or

artificial ventilation.

●No sources of ignition are to be in the immediate area when spraying, e.g. open

flame, cigarettes, sparks, glowing wires and hot surfaces.

●Before carrying out any work on the spray gun, unplug the lead from the power

socket.

●Do not use spray guns to spray flammable liquids.

W 95

●The spray guns are not to be cleaned with flammable solvents which have a

flashpoint under 21°C.

●Take precautionary measures against potential hazards from the spray liquid and

follow any instructions given on containers or laid down by the manufacturer of the

liquid.

●Do not spray any liquid of unknown hazard potential.

●Wear a breathing mask and ear protection.

Materials to be used:

Paints and varnishes containing solvents, acrylic enamel paints, water-soluble

varnishes, glazes, polishes, wood preservatives, disinfectants, plant protectives,

saturants, as well as oils and other watery liquids.

The following spray substances are not suitable for use:

Dispersion and latex paints, materials containing strong abrasives, glazes with coarse

particles, strippers and caustic solutions, silicate paints.

Use of these spray materials can lead to increased wear or corrosion damage in the

pump area, which are not covered by the WAGNER-Guarantee.

Preparing the Spray Material

The paints usually need to be diluted for use with the spray gun. You will find guidelines

for sprayable dilutions in the following viscosity table (viscosity = consistency of the

paint). You can achieve the correct dilution by using the viscosity test cup.

Technical Data W 95

Max. delivery ratee 140 g/min Container capacity: 600 ml

Max. viscosity (runout time) 60 sec. Double insulation:

Pump: Replaceable

Max. pressure spikes: 120 bar Pump cylinder: Special steel

Power source: 230 V, 50 Hz Piston: Special steel Ø 5 mm

Power consumption: 70 W Oscillation level: 10,5 m/s²

Round spray nozzle: 0,8 mm Sound pressure level: 86 dB(A)

Weight: 1,5 kg Sound pressure output: 99 dB(A)

W 95

Measuring the Viscosity

Dip the viscosity test cup (Illus. 1) completely into the spray material. Hold the test cup

up and measure the time (in seconds) until the liquid empties out. Compare the measu-

red "runout time" with the Viscosity Table.

Start-up

1. Before connecting to the mains supply, please be sure that the supply voltage is

identical with the value given on the rating plate (on the side of the spray gun).

2. Dilute the spray material according to the above table.

3. Place the container on a sheet of paper and fill it with the prepared spray material.

Attention! Do not operate the spray gun without spray

material in the container.

4. Position the spray gun on the container and turn the container to the right until the

container fits tightly (Illus. 2, arrow).

5. Activate the switch to start up the spray gun.

6. By turning the fine adjustment button you can vary the spray amount (Illus.3,arrow).

Spray Technique

●Cover areas that are not to be sprayed. When woriking keep in mind that wind, for

example, may transport paint mist over great distances and cause damage.

●Do not spray the vessel empty. The suction tube should always be immersed in liquid.

If air is sucked in, larger drops may result.

●Test the spray gun on cardboard or a similar surface to find the correct setting.

●When spraying, hold the spray gun in a horizontal position. Use the flexible nozzle

extension (Illus. 7, arrow, special accessories) for spraying upwards (e.g. a

ceiling)or downwards (e.g. an unhinged door laid on the floor).

Handling Table for Viscosity

Spray Material Viskosity: (Runout time in seconds)

Thinner-soluble varnishes/ primers 20-35 20-45

Water-soluble varnishes / primers 20-50 20-60

Automobile spray paint 18-22 18-22

Wood preservatives, disinfectants, plant protectants,

polishes, strippers, oils undiluted

Hammer effect enamel 25-35 30-45

Aluminium paints 20-30 20-30

W 95

●The spray movement should come from the arm, not just from the wrist. This

ensures that a uniform distance is maintained between the spray gun and the spray

surface during the spray operation (Illus. 4).

●To achieve optimal spray results, spray back and forth over the surface (Illus. 5).

Cleaning and Maintenance

The spray gun can only operate satisfactorily if it is cleaned and preserved

after each use.

Attention! Never immerse the spray gun in liquid when cleaning.

1 Empty out the remaining paint from the container.

2. Put proper thinner in the container and trigger the sprayer for approx. 2 seconds.

3. Pull the main plug out of the socket.

4. Disassemble the spray gun as shown in Illus. 8 (spare parts).

5. Thoroughly clean all soiled parts.

6. Reassemble the parts in reverse order.

7. Put a few drops of oil (e.g. sewing machine oil) in the intake and runback holes

(Illus. 6, arrow). Briefly switch on the spray gun.

Flexible Nozzle Extension (Illus. 7)

For spraying ceilings, resting objects or hard-to-reach areas e.g. radiators

Accessories W 95 (not included in scope of delivery)

Designation Order No.

Round spray nozzles for various spray materials:

Very thin spray materials/nozzle size: 0,5 0046 894

Paint container with cover 0414 906

Flexible nozzle extension with atomiser 0046 675

Spare Parts List W 95

Pos Name Order No.

1 Suction tube 0413 305

2 Paint container with cover 0414 906

3 Nozzle 0,8 mm 0046 903

4 Locking nut 0413 310

5 Valve 0209 042

6 Pump housing 0500 255

7 Piston spring 0033 028

8 Piston 0198 207

9 Nozzle spanner 0199 327

10 Viscosity measuring cup 0209 058

Autres manuels pour W 95

Table des matières

Autres manuels WAGNER Pistolet à peinture

WAGNER

WAGNER W 600 Manuel utilisateur

WAGNER

WAGNER FinishControl 5000 Manuel utilisateur

WAGNER

WAGNER Power Painter Manuel utilisateur

WAGNER

WAGNER 2371053 Guide rapide

WAGNER

WAGNER PEM-C2 Manuel utilisateur

WAGNER

WAGNER GA 5000EAC Manuel utilisateur

WAGNER

WAGNER GM 2800EA Manuel utilisateur

WAGNER

WAGNER CONTROL SPRAY Manuel utilisateur

WAGNER

WAGNER TOPFINISH GM 1030P Manuel utilisateur

WAGNER

WAGNER AG-08 Manuel utilisateur

WAGNER

WAGNER HIGH-PERFORMANCE AIRLESS SPRAYER Manuel utilisateur

WAGNER

WAGNER PEA-C4-HiCoat FM Manuel utilisateur

WAGNER

WAGNER HERO 23D Manuel utilisateur

WAGNER

WAGNER Cordless Lawn Sprayer Manuel utilisateur

WAGNER

WAGNER FLEXIO 3550 Manuel utilisateur

WAGNER

WAGNER PS 3.29 Manuel utilisateur

WAGNER

WAGNER w 550 Manuel utilisateur

WAGNER

WAGNER W 2400 Manuel utilisateur

WAGNER

WAGNER ProSpray 3.29 Manuel utilisateur

WAGNER

WAGNER AquaCoat 5010 GM 5020EAW Manuel utilisateur

WAGNER

WAGNER W 140 P Manuel utilisateur

WAGNER

WAGNER ProSpray 3.25 Manuel utilisateur

WAGNER

WAGNER t708 Manuel utilisateur

WAGNER

WAGNER ProSpray 23 Manuel utilisateur

Manuels Pistolet à peinture populaires d'autres marques

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manuel utilisateur

Graco

Graco 246737 Manuel d'utilisation et d'entretien

Binks

Binks SV100 Manuel utilisateur

Fimco

Fimco LG-4-3-1 Manuel utilisateur

AG SPRAY

AG SPRAY FS-ATV-25BL Manuel utilisateur

Nordson

Nordson MicroMax 2 Manuel utilisateur

Bonide

Bonide 051 Manuel d'utilisation

zogics

zogics Z-DAS Manuel utilisateur

KISANKRAFT

KISANKRAFT KK-KBS-165 Manuel utilisateur

Matrix

Matrix SG 650 Manuel utilisateur

Anest Iwata

Anest Iwata SGA-3 Guide de démarrage rapide

paasche

paasche VV Fiche technique

Carlisle

Carlisle DeVilbiss JGA-510 Manuel utilisateur

Gardena

Gardena 11120 Manuel utilisateur

Conrad

Conrad Hobby Airbrush K3 Manuel utilisateur

wiwa

wiwa 14025 R/F Manuel utilisateur

Graco

Graco EM 390 Manuel d'utilisation

DeVilbiss

DeVilbiss LUNA2i Manuel utilisateur