WABCO SMARTBOARD Note de version
SMARTBOARD
DRIVER MANUAL
2
INTRODUCTION
Monitoring a wide range of trailer functions is important for improving the performance of
haulage company operations and reducing the costs of the vehicle eet.
The SmartBoard provides a wide range of functions that can be accessed via symbols from the
main menu. The chapters below describe the various functions.
The following rules apply:
• If a system is not available and no information can be retrieved from it, the corresponding
menu symbol is not displayed.
• When the vehicle is at a standstill, the values that were last saved are displayed.
• These may deviate from the actual values (e.g. the tire pressure if a leak is present)
SMARTBOAD DRIVER MANUAL
OPERATING
INSTRUCTION
Button - Function
Selection of next menu item
or next option
Conrmation and / or execution
of the currently selected function
Back one menu level /
or save settings
Messages
Signal lamp ashing: Check current message
Driver Manual
Icon Function Display Description Options
Similar
to
Smart-
Board
icons
Name and / or
description of the
function
Description of the
information or function
you see on left display
The displayed
buttons / functions
are available for the
left display
3
TABLE OF CONTENT
Function Short Description Page
Air Suspension Operating status of the Air Suspension e.g. lifting and lowering
of vehicle body and lift axle
4
Load Monitoring Display of current axle loads 7
Mileage Counter Display of mileage and trip data 8
Messages Display of diagnostic and system messages. Check this menu
when the signal lamp ashes
8
Steering Axle Lock Lock / Unlock steering axle 8
Lining Wear Status display for the brake linings 9
SafeStart Enable / Disable automatic brake in the case of unsafe driving
conditions
9
Bounce Control Smooth release of brake to avoid bouncing caused by bogie
tension
9
Brake Release Release service brake while the vehicle is at a standstill 10
GIO Function 1 & 2 Freely congurable user functions 10
Tire Monitoring Display of tire information such as current tire pressure and
nominal pressure
10
Finisher Brake Set target braking pressure for road nishers 10
Vehicle Inclination Display of inclination angle of the trailer 11
Electronic Park Brake Enable / Disable Electronic Park Brake 11
Immobilizer Lock / Unlock trailer brakes with a PIN 12
(Immobilizer)
Emergency Release
Emergency release for trailers locked by Immobilizer 12
Actual Trailer Length Display of actual trailer length 12
Language Change language 13
Extras System information and settings 13
Codes Of Messages Short Description Page
Component: TEBS D System messages of TEBS D 16
Component: TEBS E
(TEBS D/E) System messages of TEBS E 16
Component IVTM System messages of IVTM / OptiTireTM 18
Type of fault 18
TABLE OF CONTENT
4
AIR SUSPENSION MENU
Air Suspension Menu
Function Display Description Options
Operating status of Air
Suspension Menu
Air suspension menu:
the selected function is
highlighted with a black
box and the name is
displayed in the middle of
the menu
Select next
function
Select function /
activate function
Select previous
function
Dashed box: Activated
function
Flashing: Deactivated
function
Select next
function
Select function /
deactivate function
Select previous
function
Go back to main menu:
Select the arrow Go back to main
menu
Air Suspension Functions
Function Display Description Options
Up & Down Lifting and lowering of
entire vehicle body Lift vehicle
Lower vehicle
Stop*
Front
Up & Down
Lifting and lowering of
2-point drawbar trailer Lift front axle
Lower front axle
Stop*
Rear
Up & Down
Lifting and lowering of
2-point drawbar trailer Lift rear axle
Lower rear axle
Stop*
Left Up & Down Lifting and lowering of
2-point semi-trailer Lift left side
Lower left side
Stop*
* Only if dead-man’s function is deactivated in parameterization
5
AIR SUSPENSION FUNCTIONS
Function Display Description Options
Right
Up & Down
Lifting and lowering of
2-point semi-trailer Lift right side
Lower right side
Stop*
Request
Driving Level
Lifting / Lowering to (pre-)
selected driving level Start lifting /
lowering
Vehicle is lifting / lowering Stop lifting/
lowering
Change Driving
Level
Select available Driving
Level.
Menu will be displayed
only if more than
one Driving Level is
parameterized
Select next level
Apply level
Unloading
Level
See in menu if function is
active (dashed box) or not Disable
unloading switch
(function will not be
started if switch is
active)
Lift Axle
Up & Down
The axle is lowered Lift axle
(lift axle one will
always be lifted
before lift axle two)
The axle is lifted Lower axle
(lift axle two will
always be lowered
before lift axle one)
Lift Axle OFF Lift axle one and two are
enabled Select lift axle
Disable lift axle
(lift axle stays
permanently
lowered)
Lift axle one is disabled Select lift axle
one
Enable lift axle
(lift axle can be lifted
by lift axle functions)
* Only if dead-man’s function is deactivated in parameterization
6
AIR SUSPENSION FUNCTIONS
Function Display Description Options
Traction Help Traction Help automatic
mode is activated Disable Traction
Help automatic
mode
Traction Help is
deactivated Start Traction
Help
Traction Help automatic
mode is deactivated Enable Traction
Help automatic
mode
Traction Help is activated Stop Traction
Help
OptiTurn™ OptiTurn™ automatic
mode is enabled Disable
OptiTurn™
automatic mode
OptiTurn™ is off Start OptiTurn™
OptiTurn™ automatic
mode is disabled Enable
OptiTurn™
automatic mode
OptiTurn™ is on Stop OptiTurn™
OptiLoad™ OptiLoad™ automatic
mode is enabled Disable
OptiLoad™
automatic mode
OptiLoad™ function is off Start OptiLoad™
OptiLoad™ automatic
mode is disabled Enable
OptiLoad™
automatic mode
OptiLoad™ function is on Stop OptiLoad™
Memory Level
1
Set and save Memory
Level 1 Request
Memory Level 1
Press > 5s to
store current level as
Memory Level 1
Vehicle is lifting / lowering Stop
7
AIR SUSPENSION FUNCTIONS
Function Display Description Options
Memory Level
2
Set and save Memory
Level 2 Request
Memory Level 2
Press > 5s to
store current level as
Memory Level 2
Vehicle is lifting / lowering Stop
Automatic
Level Control
Disable level control
when at a standstill Disable
temporary
Press > 5s to
disable permanently
Forklift Control Forklift Control is disabled Enable 2nd lift
axle characteristic
(due to attached
forklifter)
Forklift Control is enabled Disable 2nd lift
axle characteristic
(due to attached
forklifter)
Season
Traction Help
Season mode is off Enable Season
Traction Help
function
Date displays range of
the "season" (DD.MM to
DD.MM)*
Season mode is on Disable Season
Traction Help
function
Date displays range of
the "season" (DD.MM to
DD.MM)*
* Date is only available when the SmartBoard has an internal battery and it is parameterized in modulator.
Load Monitoring
Function Display Description Options
Display of current axle
loads
Display of current axle
loads Go to next axle
8
MILEAGE COUNTER
Mileage Counter
Function Display Description Options
Display of mileage
and trip data
Odometer Displays mileage
recorded by
SmartBoard
Go to next
item
Mileage Displays mileage
recorded by EBS Go to next
item
Trip EBS Displays trip
mileage counter
EBS
Go to next
item
Trip Displays trip
mileage counter
SmartBoard
Go to next
item
Messages
Function Display Description Options
Display of diagnostic
and system messages
Displays current active
system messages and
components.
Displays the status of the
warning lamp
Go to next
message
System messages See: Codes of Messages page 16 and following
Steering Axle Lock
Function Display Description Options
Lock / Unlock steering
axle
Steering Axle Lock is
deactivated, axle is
released
Enable steering
axle lock
Steering Axle Lock is
activated, axle is locked Disable
automatic function for
steering axle
9
LINING WEAR
Lining Wear
Function Display Description
Status display for
brake linings
All brake linings have a sufcient thickness and
are OK
At least one brake lining has reached a wear
limit. Please contact a workshop
SafeStart
Function Display Description Options
Enable / Disable
automatic brake in
case of unsafe driving
condition
(overruling the
functional switch)
The brake is applied
(function was activated by
switch)
Release
SafeStart brake
(parking brake has to
be applied before)
The brake is released Apply SafeStart
brake (parking brake
has to be applied
before)
Bounce Control
Function Display Description Options
Smooth release
of brake to avoid
bouncing caused by
bogie tension
Bounce Control function
is deactivated Activate Bounce
Control - only
possible if park brake
is engaged
Bounce Control function
is active Deactivate
Bounce Control
10
BRAKE RELEASE
Brake Release
Function Display Description Options
Conrm total release
of brake
Mind all safety
precautions!
Safety function. User
has to mind all safety
precautions
Release brake
GIO Function 1 & 2
Function Display* Description Options
Enable / Disable
customer function 1
(/ 2)
Display and control options depend on customized function.
For information about GIO functions, please contact your WABCO service partner.
Tire Monitoring
Function Display Description Options
Display of tire
pressure information
Displays the current and
nominal tire pressure from
IVTM / OptiTireTM system
Go to next tire
pressure
Finisher Brake
Function Display Description Options
Finisher Brake Finisher Brake is
deactivated Enable Finisher
Brake
Switch to brake
pressure mode
Finisher Brake is
activated Disable Finisher
Brake
Switch to brake
pressure mode
Finisher Brake Setting brake pressure in
steps of 0.1 bar Increase brake
pressure
Decrease brake
pressure
Autres manuels pour SMARTBOARD
1
Table des matières
Autres manuels WABCO Instrument de mesure
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur