Vulcan-Hart TK35 Manuel utilisateur

INSTALLATION &

OPERATION MANUAL

VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791

FORM 30608 (Rev. A, 8-95)

TK SERIES STANDARD AND

FILTER-READY GAS FRYERS

STANDARD FILTER-READY

MODEL FRYER FRYER

TK35 ML-52096 ML-52062

TK45 ML-52097 ML-52063

TK65 ML-52098 ML-52064

MODEL TK35

— 2 —

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS

EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND

ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE

EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED

FROM THE LOCAL GAS SUPPLIER.

IMPORTANT

IN THE EVENT A GAS ODOR IS DETECTED, SHUT

DOWN UNITS AT MAIN SHUTOFF VALVE AND

CONTACT THE LOCAL GAS COMPANY OR GAS

SUPPLIER FOR SERVICE.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER

FLAMMABLE VAPORS OR LIQUIDS IN THE

VICINITY OF THIS OR ANY OTHER APPLIANCE.

WARNING

IMPROPER INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR MAINTENANCE CAN

CAUSEPROPERTYDAMAGE,INJURYORDEATH.

READ THE INSTALLATION, OPERATING AND

MAINTENANCE INSTRUCTIONS THOROUGHLY

BEFORE INSTALLING OR SERVICING THIS

EQUIPMENT.

IN THE EVENT OF A POWER FAILURE, DO NOT

ATTEMPT TO OPERATE THIS DEVICE.

— 3 —

Installation, Operation and Care of

TK SERIES STANDARD & FILTER-READY GAS FRYERS

KEEP THIS MANUAL FOR FUTURE REFERENCE

GENERAL

Vulcan-Hart TK Series Fryers are available in three different models with varying capacities:

Product Lb Total Lb

Model Per Basket of Product

TK35 11/23

TK45 21/25

TK65 3 6

Your Vulcan-Hart Gas Fryer is produced with quality workmanship and material. Proper installation,

usage and maintenance of your fryer will result in many years of satisfactory performance. It is

suggested that you thoroughly read this entire manual and carefully follow all of the instructions

provided.

Separate installation instructions for the components of a filter-ready fryer are included in the MF50

and MF85 Mobile Filter Installation and Operation Manual.

INSTALLATION

Beforeinstalling thefryer, verifythat thetype ofgas (naturalor propane)agrees withthe specifications

on the fryer data plate which is located on the inside of the door panel. Also ensure the fryer is built

for installation elevation.

UNPACKING

This fryer was carefully inspected before leaving the factory. The transportation company assumes

full responsibility for safe delivery upon acceptance of this shipment. Immediately after unpacking the

fryer, check it for possible shipping damage. If the fryer is found to be damaged, save the packaging

material and contact the carrier within 15 days of delivery.

The following accessories should be packaged in the fry tank area:

Crumb screen Drain pipe

Basket hanger (2) Twin fryer baskets

Clean-out rod (4) Legs

Do not use the door or its handle to lift or move the fryer.

— 4 —

LOCATION

The equipment area must be kept free and clear of combustible substances.

Minimum clearance from combustible and non-combustible construction is 6" from the sides and 6"

from the back of the fryer. There must be at least 16" clearance between the fryer and any open top

flame units. Adequate clearances for servicing and proper operation must be allowed.

The fryer may be installed on combustible floors.

Install the fryer in an area with sufficient air supply for combustion of the gas at the fryer burners.

Provide adequate clearance for air openings into the combustion chamber. Do not obstruct the flow

of combustion and ventilation air.

Do not permit fans to blow directly at the fryer. Wherever possible, avoid open windows next to the

fryer sides or back. Avoid wall-type fans which create air cross currents within the room.

INSTALLATION CODES AND STANDARDS

Vulcan-Hart fryers should be installed in accordance with:

1. State and local codes.

2. NationalFuelGasCode,ANSI-Z223.1(latestedition),availablefromtheAmericanGasAssociation,

Inc., 1515 Wilson Blvd., Arlington, VA 22209.

3. NFPA Standard #96, "Vapor Removal from Cooking Equipment," available from the National Fire

Protection Association, Attention Publication Services, Batterymarch Park, Quincy, MA 02269.

ASSEMBLY

The fryer must be restrained with adequate ties to prevent tipping when installed in order to avoid the

splashing of hot liquid.

Legs

Position fryer in an open space near final installation area. Tilt fryer on its side, being careful to avoid

scratching the finish. Thread legs into mounting plates provided on bottom of fryer by screwing in a

clockwise rotation.

Carefully raise fryer to its normal position and place it in installation location.

Casters

When casters are assembled to the fryer, you must use a connector (available from Vulcan-Hart) that

complies with the Standard for Connectors of Movable Gas Appliances, ANSI-Z21.69 (latest edition),

and a quick-disconnect device that complies with the Standard for Quick-Disconnect Devices for Use

With Gas Fuel, ANSI-Z21.41 (latest edition).

— 5 —

Fig. 1

If it is necessary to disconnect the restraint, turn off the gas supply before disconnection. Reconnect

the restraint before turning the gas supply on and returning the fryer to its installation position.

Instructions for installing casters to the fryer are included with the casters.

GAS CONNECTIONS

CAUTION: All gas supply connections and any pipe joint compound used must be resistant to

the action of liquefied petroleum gases.

The gas inlet is located at the rear of the fryer on the lower left-hand side.

Codes require that a gas shutoff valve be installed in the gas line ahead of the fryer.

The gas supply line must be at least the equivalent of 1/2" iron pipe. If using the optional quick-

disconnect flex hose, 3/4" iron pipe must be used, unless you utilize 3/4" to 1/2" reducing fittings. Make

sure the pipes are clean and free of obstructions, dirt, and piping compound.

WARNING: PRIOR TO LIGHTING, CHECK ALL JOINTS IN THE GAS SUPPLY LINE FOR LEAKS.

USE SOAP AND WATER SOLUTION. DO NOT USE AN OPEN FLAME.

After piping has been checked for leaks, all piping receiving gas should be fully purged to remove air.

GAS PRESSURES AND ORIFICES

The standard orifices are set at 4" W.C. (Water Column) pressure for natural gas and 10" W.C. (Water

Column) pressure for propane gas. A pressure regulator is supplied as part of the gas control valve.

Provide a restraining device for the gas line to limit movement of the fryer without depending on the

connector and/or any quick-disconnect device or its associated piping to limit movement of the fryer.

Attach the restraint to the rear of the fryer (Fig. 1).

STRAIN RELIEF

FITTING FOR GAS LINE

THIS SIDE ONLY. (To be

supplied by others.)

PL-51194

—6 —

TESTING THE GAS SUPPLY PIPING SYSTEM

When test pressures exceed 1/2psig (3.45 kPa), the fryer and its individual shutoff valve must be

disconnected from the gas supply piping system.

Whentestpressuresare1/2psig(3.45kPa)orless,thefryermustbeisolatedfromthegassupplypiping

system by closing its individual shutoff valve.

LEVELING THE FRYER

Once gas connections have been made, place a carpenter's level on top of the fryer. Adjust the legs

to ensure that the fryer is level front-to-back and side-to-side in the final installed position.

FLUE CONNECTIONS

The fryer must be located under a hood with an adequate connection to an exhaust duct and with a

6" extension beyond fryer sides.

Adequate ventilation must be provided and must comply with applicable portions of National Fire

Protection Association Standard #96, "Standard for the Removal of Vapor from Cooking Equipment"

(latest edition), and with local codes.

Clearance above fryer should be adequate for products of combustion to be removed efficiently. An

18" minimum clearance should be maintained between the flue vent and the filters of the hood venting

system.

Never make flue connections directly to the fryer.

Do not obstruct the flow of flue gases from the flue duct located on the rear of the fryer.

Adequate air should be provided in the kitchen to replace air taken out by the ventilating system. This

will prevent fryer function from being affected by a reduced atmospheric pressure.

ELECTRICAL CONNECTIONS (FILTER-READY FRYERS ONLY)

WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE

APPLICABLEPORTIONSOFTHENATIONALELECTRICALCODEANSI/NFPA-70(LATESTEDITION)

AND/OR OTHER LOCAL ELECTRICAL CODES.

WARNING: APPLIANCESEQUIPPEDWITHAFLEXIBLEELECTRICSUPPLYCORDAREPROVIDED

WITHATHREE-PRONGGROUNDINGPLUG. ITISIMPERATIVETHATTHISPLUGBECONNECTED

INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE. IF THE RECEPTACLE IS NOT

THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT REMOVE THE

GROUNDING PRONG FROM THIS PLUG.

The TK35, TK45, and TK65 filter-ready fryers are equipped with a 115 volt/60 Hz./1 Phase cord and

plug which requires only that it be plugged into a properly grounded 120 volt receptacle.

Do not connect fryer to electrical supply until after gas connections have been made.

—7 —

OPERATION

WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING,

CLEANING AND SERVICING THE FRYER.

WARNING: SPILLING HOT FRYING COMPOUND CAN CAUSE SEVERE BURNS. DO NOT MOVE

FRYER WITHOUT DRAINING ALL FRYING COMPOUND FROM THE TANK.

PRIOR TO FIRST USE

Cleaning the Fryer

Using a non-corrosive, grease-dissolving commercial cleaner, clean the protective metal oils from all

surfacepartsandthetankinterior. Followthecleanermanufacturer'sdirections. Rinsethoroughlyand

drain by opening the drain valve accessible when the door is opened. Wipe tank completely dry with

a soft clean cloth.

Clean all fryer accessories. Rinse all parts thoroughly after cleaning and wipe dry.

Seasoning

Light seasoning of the backsplash area is required to avoid possible surface corrosion. With a soft,

lint-free cloth, apply a thin layer of cooking oil over entire backsplash area. This should also be done

after every cleaning.

FILLING THE FRY TANK WITH LIQUID SHORTENING

Tank warranty may be voided by improper operation. Turn gas valve off when draining or filling.

Using only liquid shortening, fill fry tank to the "oil level" line on the back wall, which appears about

3" above the tank tubes (Fig. 2)

Fig. 2

OIL LEVEL

COLD ZONE

PL-50321

—8 —

Melting solid shortening in the fry tank is not recommended. The fry tank will be damaged and the

shortening will be scorched.

Do not overfill fry tank.

Keep level of shortening at "oil level" line in fry tank. Add fresh shortening as needed.

USING THE FRYER

A high limit device will shut the fryer down should the shortening overheat. Pilot relighting will be

required. DO NOT relight pilot until shortening temperature has lowered to at least 300°F. If this

situation persists, contact your local Vulcan-Hart authorized service office.

Lighting Instructions

Fig. 3

1. Turn thermostat knob (located behind door panel) (Fig. 3) to OFF position.

2. Push gas valve extension arm in and turn arm to pilot OFF position (Fig. 3). Wait 5 minutes for

unburned gas to vent.

3. Push gas valve extension arm in and turn to the PILOT position.

4. While still depressing arm, light the pilot with a lit taper. Continue with Steps 2, 3, and 4 until pilot

remains lit when extension arm is released.

5. Turn gas valve extension arm to the ON position.

6. Repeat the above procedures if gas supply is interrupted.

200

250

300

OFF

PILOT

OFF

PL-50293

—9 —

Turning the Fryer On

CAUTION: Before turning burners on, fry tank must be filled with liquid shortening. If this is

not done, the tank walls can be damaged. Warpage can cause leaks.

To turn the fryer ON, set the thermostat knob to the desired temperature.

When the set temperature is reached, the gas control shuts off gas flow into the burners and the flame

is extinguished. From then on, the burners will cycle on and off to maintain set temperature.

Turning the Fryer Off

1. Turn thermostat knob to OFF.

2. Turn gas valve extension arm to the PILOT position (the pilot will continue to burn).

3. To shut off all gas to the system, including the pilot, turn gas valve extension arm to OFF position.

Extended Shutdown

1. Turn manual gas shutoff valve to OFF.

2. Turn thermostat knob to OFF.

3. Turn gas valve extension arm to OFF.

4. After draining and cleaning, apply a thin film of cooking oil to tank interior and tank back to inhibit

possible surface corrosion.

FRYING

Heat shortening to set temperature.

Pieces of product to be fried should be about the same size to ensure the same doneness.

Drain or wipe dry raw or wet foods to minimize splatter when lowering into the hot oil.

Do not overfill baskets. Recommended maximum capacities are shown in the GENERAL section of

this manual.

Carefully lower baskets into oil.

When frying doughnuts and fritters, turn product only once during frying.

When cooking French fries or onion rings, shake basket several times in a way that does not splatter

the shortening.

Batter-covered foods should be dropped carefully, one by one, into shortening or basket. If you use

the basket, first cover basket with shortening to reduce batter build-up on basket surfaces.

—10 —

Whenfryingiscompleted,removebasketsorproduct. Hangbasketsonrearbaskethangers. Remove

food and season it. Do not salt food over the shortening because salt could cause a chemical change

in the oil.

Add approximately 15% new oil daily.

Keep level of shortening at oil level line in fry tank. Add fresh shortening as needed.

DAILY FILTERING

Standard TK Fryers

Turn gas valve OFF when draining or filling.

Always filter the shortening while liquefied. If you attempt to drain a cold fryer, heated up, it will not

drain properly because the shortening under the cold zone tube area will remain hard. If necessary,

the clean-out rod may be used to carefully stir up hard fat to an area above the tubes where it will melt.

After the cold zone is liquefied, turn the fryer thermostat and gas valve off.

Shortening life will be extended by filtering at least once a day, or more often if conditions warrant. A

commerciallyavailablepowerfilter(madebyothermanufacturers)maybeused. Followtheiroperating

instructions for draining, straining, and replacing shortening in the fry tank.

Another way to filter is to drain the shortening from the drain pipe through a filter bag, or cover the

receiving container with cheesecloth or other filtering material.

Filtering Procedure

1. Turn the fryer OFF.

2. Slowly remove the baskets, especially if shortening is hot, to prevent splashing.

3. Open the fryer door and attach the drain pipe to the drain valve.

4. Selectacontainerofsufficientsizetohandletheamountoffryershorteningtobedrainedandplace

it below the drain pipe.

5. If you are using a filter bag, tie it securely to the drain pipe. If other filter medium is used, place it

in the container.

6. Open the drain valve carefully so that the shortening stream is directed through the filter.

7. With a small amount of warm shortening, flush out scraps and sediment in the fry tank. Drain the

tank thoroughly and wipe clean.

8. If it is necessary to clean the tank more thoroughly, follow the procedure shown in CLEANING —

WEEKLY OR AS REQUIRED.

9. Close the drain valve.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Vulcan-Hart Friteuse

Vulcan-Hart

Vulcan-Hart GRC35 Manuel utilisateur

Vulcan-Hart

Vulcan-Hart VK SERIES Manuel utilisateur

Vulcan-Hart

Vulcan-Hart ML-136407 Manuel utilisateur

Vulcan-Hart

Vulcan-Hart LG300 Manuel utilisateur

Vulcan-Hart

Vulcan-Hart ERD40 Manuel utilisateur

Vulcan-Hart

Vulcan-Hart SPER1 ML-52918 Manuel utilisateur

Vulcan-Hart

Vulcan-Hart 1GR35M Mode d’emploi

Vulcan-Hart

Vulcan-Hart 1GR45A Manuel utilisateur

Vulcan-Hart

Vulcan-Hart GRS25 Manuel utilisateur

Vulcan-Hart

Vulcan-Hart ECONOFRY EF3 ML-52099 Manuel utilisateur

Vulcan-Hart

Vulcan-Hart GRC35 ML-052083 Manuel utilisateur

Vulcan-Hart

Vulcan-Hart GRS25 Manuel utilisateur

Vulcan-Hart

Vulcan-Hart QUICKFRY VHG-A Series Manuel utilisateur

Vulcan-Hart

Vulcan-Hart VK SERIES Manuel utilisateur

Vulcan-Hart

Vulcan-Hart 1GR65C Manuel utilisateur

Vulcan-Hart

Vulcan-Hart GR25 Manuel utilisateur

Vulcan-Hart

Vulcan-Hart GHF91G Manuel utilisateur

Vulcan-Hart

Vulcan-Hart ERA Series Manuel utilisateur

Vulcan-Hart

Vulcan-Hart 1G8BD Series Manuel utilisateur

Vulcan-Hart

Vulcan-Hart GRM SERIES Guide de démarrage rapide

Vulcan-Hart

Vulcan-Hart 2XG45DF Manuel utilisateur

Vulcan-Hart

Vulcan-Hart GHF90 Manuel utilisateur

Vulcan-Hart

Vulcan-Hart 1GR45C Manuel utilisateur

Vulcan-Hart

Vulcan-Hart ECONOFRY EF3 ML-52099 Manuel utilisateur

Manuels Friteuse populaires d'autres marques

Innsky

Innsky 55SA1US Manuel utilisateur

Falcon

Falcon G350/11 Guide de l'utilisateur

GoWISE USA

GoWISE USA GW22612 Manuel utilisateur

Wolf

Wolf IF15/S Manuel utilisateur

Electrolux

Electrolux Thermetic 9CHG583284 Guide rapide

Gourmia

Gourmia GAF799 Manuel utilisateur

DeLonghi

DeLonghi D677UX Manuel utilisateur

SEVERIN

SEVERIN DEEP FRYER - Guide de l'utilisateur

Toastmaster

Toastmaster TMFG18-NAT Manuel utilisateur

Domo

Domo DO465FR Manuel utilisateur

Henny Penny

Henny Penny PFG-691 Manuel utilisateur

Farberware

Farberware FBW FT 43721 B Manuel utilisateur

GERMANICA

GERMANICA GEAF5L3LD Manuel utilisateur

Roller Grill

Roller Grill MF 120 R Manuel d'utilisation

Philips

Philips HD9211 Manuel utilisateur

Linea 2000

Linea 2000 Domo DO536FR Manuel utilisateur

Lakeland

Lakeland 31796 Manuel utilisateur

Dash

Dash Tasti-Crisp DFAF755 Manuel utilisateur