Vivotek SD9361-EHL Manuel utilisateur

Quick Installation Guide

VIVOTEK INC.

6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.

|T:+886-2-82455282|F:+886-2-82455532|E:[email protected]

VIVOTEK USA, INC.

2050 Ringwood Avenue, San Jose, CA 95131

|T: 408-773-8686 |F: 408-773-8298 |E: [email protected]

2MP • 20x/30x Zoom • 60fps • NEMA 4x • IP68 • Extreme Weatherproof

All specications are subject to change without notice.

P/N:625033602G Rev.: 1.2

SD9362-EH/EHL Speed Dome

Network Camera

English 繁中日本語 Español Português

簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska

Dansk

Nederlands

Indonesia

VIVOTEK Europe

Randstad 22-133, 1316BW Almere, The Netherlands

T:+31(0)36-5298-434 E:[email protected]

SD9361-EHL

EN-1

English

Warning Before Installation

Refer to your user’s manual for the

operating temperature.

Power off the Network Camera as soon as

smoke or unusual odors are detected.

Do not touch the Network Camera during

a lightning storm.

Do not disassemble the Network Camera.

Do not drop the Network Camera.

Do not insert sharp or tiny objects into the

Network Camera.

Do not manually pan and tilt the Network

Camera when the power is on.

Package Contents

Software CD

Wall Mount Bracket / ScrewsSD9361/ SD9362

Quick Installation Guide

I/O Combo Cable

Screws / Alignment Sticker / T20 and T25

L-wrench / Desiccant Bags

IMPORTANT:

Below are the requirements for powering the the speed dome:

Feature Power Consumption

Normal w/ heater 48W, requires a 60W PoE injector (AP-GIC-010A-060) or PoE switch (AW-

IHU-0100, -0200, -0600); AC24V (3.5A) also applies

w/ IR unit 95W, VIVOTEK's AW-IHU-0101 & AW-IHU-0201

DC 24V (3.5A) applies, AC 24V is not sufcient.

EN-2

Top View

IR unit connector

Lens

Outer View

Physical Description

LAN connector

Status LED

Reset Button

This drawing shows a camera with its dome

cover removed.

MicroSD card slot

Safety wire hook

I/O combo connector

Alignment marks

EN-3

English

Hardware Installation

Ø 9.5mm or 3/8”

1. Jot down the camera's MAC address for later reference.

2. The camera weighs 3kg. Select a rigid mounting location to prevent vibration to the

camera. Attach the alignment sticker to the wall.

3. Drill 4 pilot holes (9.5mm in diameter and 4cm deep) into the wall, and then hammer

in threaded anchors. Note that you should hammer the anchors with hex nuts on

them so that the threaded poles will not be deformed! If preferred, drill another hole

for routing cables.

4. Remove the hex nuts, washers, and leave one washer on each of the threaded poles.

0002D10766AD

SDXXXX

EN-4

LAN I/O combo

5. Connect power or I/O wires, and use foam tapes or seal foam to ensure the back-end

connection is waterproof.

6. Route your I/O combo and Ethernet cables along the routing guide poles to form drip

loops.

EN-5

English

7. Secure the bracket to wall.

15cm

8. Remove the cable gland from the LAN port. If I/O wires

or 24V power are preferred, use the T20 L-wrench to

remove the top cover on the I/O connectors.

T20

The cable length hanging on the out-

side of the bracket should be 15cm

IMPORTANT:

Make sure all waterproof cable glands have

been properly installed. Water leakage will

cause irrepairable damage to the camera.

EN-6

9. Hook up the safety wire between the bracket and the camera.

4.3 ~ 6.4mm

10. Install the components of the waterproof cable gland to the Ethernet and I/O com-

bo cables.

The outer jacket

of the combo

cable is ush with

cabling hole.

EN-7

English

11. Connect the I/O wire headers to camera and then secure the top cover.

T20

12. Connect the Ethernet cable (along with its cable gland) to the camera.

NOTE:

To disconnect a LAN cable, loosen the cable

gland and pull the cable against the socket

wall towards the side of the locking tab.

EN-8

13. Install the camera to bracket by aligning the mark on bracket with the #1 marking

on the camera.

14. Turn the camera clockwise. The camera should be locked in place.

15. Secure the connection using the T25 L-wrench from

the top.

T25

EN-9

English

16. Open the dome cover using the T20 L-wrench. Install a microSD card, and replace

the desiccant bag on the inner side of camera chassis.

icro

T20

17. Remove the foam blocks in the chassis, and the front and rear of the lens module.

Also remove the plastic sheet from the inside of the dome cover.

18. When done, secure the dome cover

using the T20 L-wrench.

Autres manuels pour SD9361-EHL

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Vivotek Caméra de sécurité

Vivotek

Vivotek Supreme SD9363 Manuel utilisateur

Vivotek

Vivotek IP8371E Manuel utilisateur

Vivotek

Vivotek IB8367-R Manuel utilisateur

Vivotek

Vivotek IP7133 Manuel utilisateur

Vivotek

Vivotek FD8138-H Manuel utilisateur

Vivotek

Vivotek FD9366-HV Manuel utilisateur

Vivotek

Vivotek PD8136 Manuel utilisateur

Vivotek

Vivotek Supreme SD9374-EHL Manuel utilisateur

Vivotek

Vivotek FD8133V Manuel utilisateur

Vivotek

Vivotek FD8366-V Manuel utilisateur

Vivotek

Vivotek 4X-PT7135 Manuel utilisateur

Vivotek

Vivotek Supreme MS8392-EV Manuel utilisateur

Vivotek

Vivotek IB8377-HT Manuel utilisateur

Vivotek

Vivotek IP8336W Manuel utilisateur

Vivotek

Vivotek IP2112 Manuel utilisateur

Vivotek

Vivotek VORTEX FD839-EHV Manuel utilisateur

Vivotek

Vivotek FD8161 Manuel utilisateur

Vivotek

Vivotek VC8201 Manuel utilisateur

Vivotek

Vivotek V Series Manuel utilisateur

Vivotek

Vivotek FD816B-H(T) Manuel utilisateur

Vivotek

Vivotek IT9389 Series Manuel utilisateur

Vivotek

Vivotek Supreme FD8363 Manuel utilisateur

Vivotek

Vivotek IP6122 Manuel utilisateur

Vivotek

Vivotek IP8352 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur

Lumens

Lumens VC-A50PNW Manuel utilisateur