Vitek VTC-IRH30E2810 Manuel utilisateur
FEATURES:
• 1/3” Panasonic Progressive Scan CMOS Sensor
• 2.1 MegaPixel with Full 1080p/720p HD-SDI (SMPTE292M) EX-SDI Output
• 30 Dynamic Infrared LEDs at 850nm enable viewing in total darkness up to
100 feet
• Dynamic Intensity IR LEDs to reduce over saturation of IR illuminated video
without engaging the Image Signal Processor chip
• MegaPixel IR Corrected 2.8-10mm Varifocal Auto Iris Lens with External
Adjustments for Focus and Zoom
• True Day/Night by ICR - Dual Filter Switch
• Fully programmable True WDR (Dual Scan) at 30fps
• Smart Motion Zoom tracks motion, then intelligently zooms into that area of
the frame
• 3D-DNR Advanced Digital Noise Reduction
• Dual Glass Compartments to Eliminate IR Reflection
• Secondary Video Output & OSD Control Joystick are accessible inside a
gasket sealed removable side panel
• Advanced OSD Functions: Smart Motion Zoom, Focus Assist, Motion
Detection, Privacy Mask, Defog, D-Zoom(~8x), Sens-up(~x32), BLC/HLC,
Title Set, Pixel Defect Compensation, Lens Shade Compensation
• 100% Pure Digital Transmission of video data
• Up to 1000’ HD Transmission Range (Depending on cable characteristics and
integrity)
• 3-Axis mount with Simple One Turn Positioning Lock for Ease of Installation
• IP-67 Rated Water Resistance
• 12VDC / 24VAC Dual Voltage Operation
VTC-IRH30E2810
2.1MP HD-SDI / EX-SDI WDR
Bullet Camera with 30 IR LEDs
VITEK
VITEK
Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
2 3
Safety Precaution
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.
3
Contents
Safety Precaution
p.02~03
Contents
p.04
Features
p.05~06
Composition
p.06
Dimensions
p.07
Part Names
p.08
Installation Instructions
p.09~11
Operating Instructions
p.12~28
Specifications
p.29
4 5
Features
Key Features
• Full HD, 2Mega Pixel EX-SDI CAMERA, 1920x1080(30p)
• Extended long reach HD Solution
• Real time True WDR(Wide Dynamic Range) / 30fps
• Improved noise figure with the enhanced 3DNR
• Built-in f=2.8~10mm F1.4, Mega-pixel DC Auto Iris vari-focal lens
• TDN by Dual Filter Switcher
• Day & Night Simulation for easy focus adjustment
• Various Zooming Technologies
- Pointing Zoom (which enables the programmable zooming at any area)
- Preset Zoom
- Flex Zoom
- Smart Motion Zoom (Automatic zoom in/out when motion is detected)
• Motion Detection, Privacy Mask, Smart IR, Sens-up(~x32), D-WDR,
H/V/HV Flip, D-Zoom(~8x), BLC/HLC, Lens Shade Compensation,
Pixel Defect Compensation, Title Set, Defog
• EX-SDI or HD-SDI switchable
• Top performance at low light sensitivity (Sens-up On)
• OSD menu & CVBS Video output BNC for easy installation & maintenance.
• Reverse polarity protection circuit
• Isolated power supply against ground loop problem
• Remote control via RS-485 (Pelco-D/P)
• Quick Firmware update via RS-485
• External Zoom & Focus adjustment
• Built-in 30pcs IR-LED
• Dual Window
• One-touch 3-Axis locking bracket
• IP67 protection
• Power: 24VAC/12VDC
5
General Description
• With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accepts the infrared light
• With Intelligent Focus Indicator and FOCUS ASSIST menu,
- Offers easy adjustment of Focus
- Eliminates the mistake of the erratic focus adjustment
• With 24VAC/12VDC dual power design,
- Offers the flexibility of installation
- Ensures the reliability
This camera realizes the natural and crisp image as you see the scene in front
of you by Full HD(1920x1080p) camera module.
Highly detailed pictures can be achieved and color reproducibility deserves
attention.
Composition
Features
Torque Wrench:
3mm (1pc)
Video Sub-out:
Cable (1pc)
Mounting Screw:
4 x 40mm (3pcs)
Plastic Anchor:
6 x 30mm (3pcs)
Mounting
Template
Operating
InstructionCamera
Cable Signal
Sticker
Wiring Connector:
(1pc)
6 7
Dimensions
(unit : mm)
• Extreme care should be taken NOT to scratch the window in front of lens.
• Care should be taken that the cable is NOT damaged, kinked or exposed in
a hazardous area.
• Do not point the camera lens directly at the sun or a spot light.
CAUTION
3.43”
3.73”
3.17”
9.29”
9.72”
Ø3.64”
7
Part Names
DUAL WINDOW
POWER
CABLE
SUNSHIELD BOLT
BOTTOM
VIEW
SUNSHIELD
FRONT CASE
OSD Setup
CONTROL COVER
BRACKET
REAR CASE
FOCUS ZOOM
8 9
Installation Instructions
Mounting Screw
: 4x40mm
1. Locate the mounting template at the installation position and drill the ceiling
or wall if needed.
2. Route the Power cable to the connecting place.
3. Place the camera bracket on pre-drilled position and fix it through using mounting
screws (4x40mm).
4. Set the camera’s viewing angle and adjust zoom/focus of lens by using the L-wrench.
5. Put the sunshield to the camera unit and tighten the sunshield-bolt.
■Adjustment of viewing angle
with one-touch 3-Axis bracket
Torque
wrench
Lock/Unlock
Screw
9
Installation Instructions
Pan & Tilt adjustments
Zoom & Focus adjustments
1) Pan limit:
Pan is limited to +/- 90°.
3) Inclination limit
(Horizontal image alignment):
Inclination limited to +/-90° max.
2) Tilt limit:
Tilt is limited to 0°(2°) min ~ 90° max.
for wall(ceiling) installation respectively with
reference to the wall(ceiling) when the
inclination of camera module is 0°, that is,
the image is aligned horizontally.
90° 90°
• Turn the Focus gear to “N”(Near) or “∞”(Far)
until the sharpest focus is made.
• To widen the viewing angle, turn the Zoom
to “W”(Wide) and to obtain a closer view,
turn it to “T”(Tele)
Use the torque wrench supplied.
• Unlock the screw on the camera bracket through using the torque wrench
supplied
• Set the camera’s viewing angle then lock the screw on the bracket.
90°
90°
±90°
•on the wall •on the ceiling
10 11
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Vitek Caméra de sécurité
Vitek
Vitek VT-PTZ12WH Manuel utilisateur
Vitek
Vitek VTC-C770DN Manuel utilisateur
Vitek
Vitek VTC-B301 Manuel utilisateur
Vitek
Vitek VT-IR1C/24 Manuel utilisateur
Vitek
Vitek Transcendent VTD-TND4RFA3/-2 Manuel utilisateur
Vitek
Vitek VT-PTZ220HD Manuel utilisateur
Vitek
Vitek TRANSCENDENT VT-TPTZ10HRF-2T Manuel utilisateur
Vitek
Vitek VTC-TNB5RFEA-2 Manuel utilisateur
Vitek
Vitek VTC-TNT8RMEA Manuel utilisateur
Vitek
Vitek Transcendent VT-TPTZ30HRA-4PNS Manuel utilisateur
Vitek
Vitek TRANSCENDENT VT-TPTZ4AD-4M Manuel utilisateur
Vitek
Vitek VTC-TNB8RMA4B Manuel utilisateur
Vitek
Vitek VTC-BHOCCR212M Manuel utilisateur
Vitek
Vitek VT-TPTZ25HRAN-4PNS Manuel utilisateur
Vitek
Vitek VTD-TNMD4RFS Manuel utilisateur
Vitek
Vitek VTD-VH49B2 Manuel utilisateur
Vitek
Vitek VTC-LED697HRCB Manuel utilisateur
Vitek
Vitek VTC-IRLED30 Manuel utilisateur
Vitek
Vitek VTD-C410 Manuel utilisateur
Vitek
Vitek Transcendent VT-TPTZ-B10X5N Manuel utilisateur
