Vitek VTC-750WDR Manuel utilisateur

BLACK

VITEK

VTC-C750WDR

Wide Dynamic Range Color CCD

Camera w/550TVL

• Wide Dynamic Range 1/3" Color DPS Pixim Image Sensor

• 550 TV Lines of Resolution

• OSD (On Screen Display) for Camera Function Setup

• True (ICR) Day/Night Function

• 0.0002 Lux Sensitivity (F1.2 @40IRE Sense-Up)

• Dual Voltage Operation 12VDC/24VAC

• Over 50dB S/N Ratio

VTC-C750WDR

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

The symbol is intended to alert the user to the presence of important

operating and maintenance(servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user to the presence of

uninsulated "dangerous voltage" within the product's enclosure that

may be of sufficient magnitude to constitute a risk of electric shock

to persons.

Warning(NTSC version) -- This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Caution -- Any changes or modifications in construction of this device which are not expressly approved by the

party responsible for compliance could void the user's authority to operate the equipment.

WARNING

Caution

To prevent electric shocks

and risk of fire hazards, do

NOT use other than specific

power source.

VTC-C750WDR

Table of contents

1. Safety Instructions and Notes….......................................................................................................

2. General Descriptions............................................................................……………………………...

3. Supplied Items......................................................................................……………………………...

4. Part names…………………………….…...................................................…………………………...

5. Installation and commissioning Instructions....................................................……………………...

6. Start up…………………............................................................................…………………………...

7. Setup Menu……………………………………………….....................................................................

8. Specifications…………………………………………….....................................................................

9. Dimensional Drawings…................................................................................................................

10. Setup Menu tree……….................................................................................................................

VTC-C750WDR

1. Safety Instructions and Notes

•Please read these safety and operating instructions before putting the camera into operation.

•Keep the operating instructions in a safe place for later use.

•The Standard Box Camera is designed for indoor use only and it must not be installed where exposed to rain

and moisture.

•Do not operate the cameras beyond their specified temperature, humidity or power ratings.

•Never open the case of the camera because there are precision parts inside. Otherwise a trouble or

an accident may result

•Do not put anything metallic and other foreign substances through the vent. A trouble fire or electric shock

may result.

•Be sure to turn off the power before installing or making connection.

•Pay attention when laying the connection cable and observe that the cable is not subject to heavy loads,

kinks or damage and no moisture can get in.

•Do not install the camera in places exposed to vibrations and shocks.

•Be very careful not to drop or shock the camera while carrying it in.

•Do not orient the camera to the sun.

•Do not make any modification to the unit (neither to the software nor the hardware). Improper modification

voids the warranty and can cause malfunctions or damages.

The manufacturer accepts no liability for damages resulting from unauthorized or improper modifications to

the unit

•Some of types of lenses may cause hunting, light amount drop or other problems. In such case, readjust the

lenses.

•Because of the digital image device characteristics, images may look rugged at high temperatures. This does

not mean the camera is in trouble.

•The warranty becomes void if repairs are undertaken by unauthorized persons.

•Contact the supplier if any functional problems arise.

Cleaning:

•Do not touch the surface of the imaging device.

•Keep clean the lens surfaces at both sides of front and rear..

VTC-C750WDR

2. General Descriptions

VTC-C750WDR (VTC-C750WDR/PAL for PAL)) is a superb wide dynamic range camera which achieves

120dB max(102dB typical) of dynamic range of the image by implementing PIXIM's DPS(digital pixel system)

CMOS SENSOR.

With CMOS image sensor,

- Provides the best quality image without any blooming or vertical smear even under the spot light.

With Pixim’s DPS technology,

- Offers unparalleled image quality across all lighting conditions especially at high-contrast environments

like indoor and outdoor of daylight time

- Delivers natural color

- Offers the highest resolution of 540TVL(horizontal)

- Eliminates compromising image noise by blooming or vertical smear

- Reduces the color rolling and flicker(EFR version only of NTSC camera)

- Eliminates the color rolling of NTSC system by line-lock synchronization (AC24V version)

- Offers on-screen menu

With ICR mechanism,

- Enhances its sensitivity about 10x at night time

- Can accepts the infrared light

With 24VAC/12VDC dual power design,

- Offers the flexibility of installation

- Ensures the reliability

Main features are;

• 1/3" RGB Color DPS SENSOR (Pixim Orca D1500series)

•Resolution of 540 Horizontal Lines

•10x sensitivity enhancement by removing the optical filter

•Switches to B/W and able to accept the infrared spectrum at night mode

•Enhanced sharpness compensation

•Very low noise and superior picture quality

•Sensitivity of 0.0002Lux (B&W)

•Automatically removable IR Cut Filter

•Automatic White Balance (ATW)

•Support DC auto iris lens

•Supply voltage: 12Vdc/24Vac Dual voltage

3. Supplied Items

1 x WDR TDN Color Camera

1 x Dust protection cap

1 x Installation and Operating Instructions

VTC-C750WDR

③

①

②

④ ⑤

4. Part Names

4.1 Front view

- Lens Connector for Auto-iris lens (DC Drive)

①Back Focus Adjustment ②Dust Protection Cap

③Lens connector for auto iris lenses ④Back focus Adjustment Lock Screw

⑤Camera Mount Hole (Top and Bottom)

PIN No DC Iris

1 Damp(-)

2 Damp(+)

3 Drive(+)

4 GND

PIN4 PIN2

PIN3 PIN1

VTC-C750WDR

ⓐⓑ

ⓒ

ⓓ

4.2 Rear side view

5. Installation and commissioning Instructions

•Make sure the power is removed before the installation.

•Follow the order for applying power.

First connect the low voltage (DC12V or AC24V), then plug the AC adapter to AC outlets to avoid an

improper reset from power jitter and a damage from the surge voltage when no load.

5.1. Attaching the lens

•Remove the Dust Protection cap from the lens mount

•Screw the lens onto the camera without using force

5.2. Setting the back focus lock

The back focus is the distance between the lens support on the camera and the image sensor. Optimum focus

is only possible when the correct distance is set. It may be necessary to set the back focus in individual cases

due to production tolerances of the lens. The iris of the lens must be open as wide as possible. (smallest F

value) to set the back focus. For lenses with automatic iris control, you will require a ND filter (gray filter) to

prevent the iris from closing in bright light.

Setting for lenses with a fixed focal distance

If the focus cannot be set exactly by turning the focus ring (lens), please proceed as follows;

1. Point the camera at an object with sufficient contrast. The distance to the object should be longer than

1,000 x the focal distance.

2. Open the iris on the lens

3. Set the focus of lens so that the distance at the lens is close to infinity but not to exact infinity position.

ⓐ OSD menu switches (Up/ Down/ Left/ Right / Enter)

ⓑ Video Output Connector (BNC)

ⓓ Power Input Terminal

VTC-C750WDR

4. Loosen ④Back focus Adjustment Lock Screw one~two turns on the camera with industrial “+” driver

5. Rotate ①Back Focus Adjustment until the optimum focus is achieved.

6. Tighten ④Back focus Adjustment Lock Screw again.

7. Trim the focus precisely at lens if necessary.

Setting for lenses with a variable focal distance (zoom)

If the focus changes as the focal distance changes, please proceed as follows.

1. Point the camera at an object with sufficient contrast at a distance of approximately 2 meters.

2. Open the iris on the lens

3. Set the maximum focal distance (Tele) at the lens

4. Set the optimum focus with the focus ring

5. Set the smallest focal distance (wide angle)

6. Loosen ④Back focus Adjustment Lock Screw one~two turns on the camera with the industrial “+” driver

7. Adjust ①Back Focus Adjustment until the optimum focus is achieved. Steps 3,4,5 and 7 may be needed

to repeat several times to obtain the best results

8. Tighten ④Back focus Adjustment Lock Screw again

5.3. Installation

The camera has a 1/4” thread insert on its top and bottom side for mounting the camera to a tripod or the wall

or ceiling with a corresponding mount.

5.4 Commissioning

•Connect the power to the camera firstly

•Plug the power adaptor to the mains supply secondly

•The camera is ready for operation

5.5. Power Supply Connections

Camera can work with either 12VDC or 24VAC, dual voltage power. It does NOT require the polarity-matched

connection for 12VDC supply. Primary and secondary grounds are completely isolated to avoid the possible

ground-loop problems. Its excellently wide operating voltage range of 10.5V-30V for DC and 12-28.8V for AC

gives an extra flexibility at the installation.

6. Start up

When the camera is powered properly, it starts up with initializing the internal parameters and the filter switch

mechanism. The filter switch unit repeats IN and OUT two times at each power up and just after RESTORE

FACTORY SETTINGS.

VTC-C750WDR

7. SETUP Menu

7.1 In the menu

Use ,buttons to move menu, ,buttons to change the settings and press button short

to select or enter.

button stands for MENU or ENTER button.

7.2 Entering menu

Press button longer than 2 sec on the back of camera.

7.3 PRESET menu

PRESET menu is provided to help the settings with the possible parameters obtained and

assumed by the factory tests for the most common environments.

PRESETs may not be the best optimized settings for the actual installations.

In such cases, find the optimal settings in CUSTOM setting of EXPOSURE menu

PRESET Descriptions

<NORMAL> Produces an image that has average contrast and suitable for normal indoor or low-

contrast outdoor scenes.

INDOOR Provides better leveling of image for in the darker areas of the scene. Suitable for

indoor scenes that have higher contrast lighting.

OUTDOOR

Optimized for outdoor sunlit applications and provides better leveling for the brighter

areas. Suitable for outdoor scenes having high contrast between sunlit and

shadows.

FL-LIGHT

Reduces the color rolling by fluorescent lights when line-lock is not

available(NTSC). DC auto iris lens is required.

Use Line-lock sync. with AC24V supply for the best result against the color rolling if

possible.

LOBBY Optimized for the common installation at lobby.

WAREHOUSE Optimized for the common installation at warehouse

VTC-C750WDR

7.4 EXPOSURE menu

EXPOSURE menu is provided to help the settings with the possible parameters obtained and

assumed by the factory tests for the most common environments.

EXPOSURE presets may not be the best optimized settings for the actual installations.

In such cases, find the optimal settings in CUSTOM setting of EXPOSURE menu

7.5 CUSTOM menu

To enter CUSTOM menu, press button at <CUSTOM . . . > of EXPOSURE menu.

EXPOSURE Descriptions

<WDR MID> Medium level of the dynamic range control for each PRESETs.

WDR HIGH Increases the dynamic range control. Some highlight area may washed out.

CUSTOM... Provides more flexible compensation other than WDR MID, WDR LOW, WDR HIGH

BLC...

Compensates the brightness of main object against the bright back light.

A zone out of CTR SPOT, UPPER1/3, MIDDLE1/3, LOWER1/3 can be set.

Dynamic range control is inoperative if EXPOSURE is set to BLC.

WDR LOW Decreases the dynamic range control.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Vitek Caméra de sécurité

Vitek

Vitek VTC-TNT5RMS Manuel utilisateur

Vitek

Vitek Transcendent Series Manuel utilisateur

Vitek

Vitek VTC-MV2NZ Manuel utilisateur

Vitek

Vitek VTC-C54 Manuel utilisateur

Vitek

Vitek VTC-IRM5H-2713 Manuel utilisateur

Vitek

Vitek Transcendent VTD-THMD2RF Manuel utilisateur

Vitek

Vitek VTC-TNB4RMA4 Manuel utilisateur

Vitek

Vitek VTC-THB5R3 Manuel utilisateur

Vitek

Vitek VT-PTZ40WH Manuel utilisateur

Vitek

Vitek TRANSCENDENT VTD-TND4RMA4 Manuel utilisateur

Vitek

Vitek VTC-IR302FN Manuel utilisateur

Vitek

Vitek Transcendent VTC-TNB8MADW Manuel utilisateur

Vitek

Vitek TRANSCENDENT VTD-HOCR2812-VB Manuel utilisateur

Vitek

Vitek VTC-T4T3HR2MD Manuel utilisateur

Vitek

Vitek Mighty VTD-MVP2810/L35 Manuel utilisateur

Vitek

Vitek VTC-IR62NZ922 Manuel utilisateur

Vitek

Vitek VTC-EB25C Manuel utilisateur

Vitek

Vitek Transcendent VTC-THB2RFS Manuel utilisateur

Vitek

Vitek VTC-C574 Manuel utilisateur

Vitek

Vitek VTC-C960DS Manuel utilisateur

Vitek

Vitek VTC-TNB36R3V2 Manuel utilisateur

Vitek

Vitek VTD-AR2812 Manuel utilisateur

Vitek

Vitek Transcendent VTD-TND8RMA3 Manuel utilisateur

Vitek

Vitek Transcendent VTC-TNT4FLN-2 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Lumens

Lumens VC-A50PNW Manuel utilisateur