Vista VK2-3MPVRDIR3V9F Manuel utilisateur

Please read this manual thoroughly before use, and keep it handy for future reference.

VK2-3MPVRDIR3V9F

Quick Guide

1. Description

This manual applies to the VK2-3MPVRDIR3V9F 3 mega pixel Vandal resistant vari-focal dome with

IR illumination.

• Installation Steps

Follow these steps to install the network camera on your local network (LAN):

1. Check the package contents against the list below.

2. Connect the Network Camera. See page 3.

3. Set an IP address. See page 6.

4. Set the password. See page 8.

• Package Component

The system comes with the following components:

Camera unit Installation CD Installation Guide Template Sheet Accessory Kit

Check your package to make sure that you received the complete system, including all components

shown above.

• Contents in the installation CD

1. The Network Camera User’s Manual

2. The SmartManager User’s Manual

3. The VK2_Client User’s Manual

4. The SmartManager Installation software

5. The VK2-Client Installation software

Note:Check your package to make sure that you received the complete system, including all

components shown above.

2. Installation

For the operation of the Network Camera, it is necessary to connect a network cable for data

transmission, power connection from supplied power adapter. Depending on operation methods, it is

possible to connect an alarm cable additionally. For its fixation on different locations, please consult

with an installer.

2.1 Connection

Connection Cable

Wire Color

Description

Yellow

Ethernet, RJ-45 port compatible with 10/100Mbps having PoE

functionality. Modular Jack

Red:

AC24V/DC12V

White: AC24V/GND

Main Power, 3 pin terminal,

Pink: GND

Gray: Alarm Input

Brown: GND

Yellow: Alarm Out

Alarm Input and Output, 4pin terminal.

Red : Audio In

White : Audio Out

Black : GND

Audio Input and Output Cable.

Micro SD memory slot on the Board

Card Slot for Micro SD memory: Socket “J15”

• Connecting to the RJ-45

Connect a standard RJ-45 cable to the network port of the network camera. Generally a

cross-over cable is used for directly connection to PC, while a direct cable is used for connection

to a hub.

You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.

• Connecting Alarms

AI(Alarm In) :

You can use external devices to signal the network camera to react on events. Mechanical or

electrical switches can be wired to the AI (Alarm In) and G (Ground) connectors.

G(Ground) :

Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.

Alarm Out :

The network camera can activate external devices such as buzzers or lights. Connect the device

to the AO (Alarm Out) and G (Ground) connectors.

• Connecting the Power

Connect the power of DC12V or AC24V for the network camera. Connect the positive(+) pole to

the ‘+’ position and the negative(-) pole to the ‘-‘ position for the DC power.

Be careful not to reverse the polarity when you connect the power cable.

You can also use a router featuring PoE (Power over Ethernet) to supply power to the

camera.

The heater will operate properly only by the power source of AC 24V.

If using PoE, the heater will not operate at all.

If PoE and DC 12V are both applied, this camera will get supplied with power from PoE.

• Connecting Service Monitor Port (using VK2-LCT)

Service monitor output port (J7) is located on the board of the dome camera, and is used for an

easy OSD setup.

▶ID & IP assignment

To make changes in the OSD menu, please use the OSD controller provided optionally with your

camera purchase. You can set Camera Title and IP Address.

1. Connect the OSD Controller to the Service Monitor port of the network camera.

2. Connect Service Monitor and the Video Output port of the OSD Controller.

3. Press the SET button to access main Menu.

4. Change Camera ID, and IP Address. You can change the Name or Title and IP address of the

camera. Using the ↑↓←→ buttons on the controller, you can change the parameters.

5. Select SAVE or CANCEL to exit the Main Menu.

Video Output is used for an easy zoom and focus control when installing lens. Video Output is

restricted to 704x480(576) resolution.

▶Zoom & Focus Control

The camera enters Zoom and Focus control mode as soon as connecting OSD Controller to the

Service Monitor port.

-. Zoom Control: ↑(Zoom In), ↓(Zoom Out)

-. Focus Control: ←(Focus Near), →(Focus Far)

-. Smart Focus: Press and hold the SET button for 2 or more seconds. The camera readjusts

focus automatically.

Note: You can get the Optional OSD Controller from your installer.

Heater Kit Installation(Optional)

1. Place the heater element is slot “A”. Please ensure that the cables are facing upwards and the

heater is pointing towards the Dome.

2. Place the plug in the Connector “B”(J13) which is found on the controller board.

•

Power Supply

24VAC

Power Consumption

20Watt

Heater On

at 41°F (5°C)

Heater Off

at 59°F (15°C)

2.2 Network Connection and IP assignment

The Network Camera supports the operation through the network. When a camera is first connected to

the network it has no IP address. So, it is necessary to allocate an IP address to the device with the

“Smart Manager” utility on the CD. The factory default IP is “192.168.30.220”.

1. Connect the Network Camera / device to the network and power up.

2. Start SmartManager utility (All Programs>SmartManager>SmartManager), the main window will

be displayed, after a short while any network devices connected to the network will be displayed

in the list.

3. Select the camera on the list and click right button of the mouse. You can see the pop-up menu

as below.

4. Select Assign IP. You cam see a Assign IP window. Enter the required IP address.

3. Operation

The Network Camera can be used with Windows operating system and browsers. The recommended

browsers are Internet Explorer, Safari, Firefox, Opera and Google Chrome with Windows.

3.1 Access from a browser

1. Start a browser (Internet Explorer).

2. Enter the IP address or host name of the Network Camera in the Location/Address field of your

browser.

3. You can see a starting page. Click Live View or Setup to enter web page.

4. The network camera’s Live View page appears in your browser.

3.2. Access from the internet

Access from the internet once connected, the Network Camera is accessible on your local network

(LAN). To access the network camera from the Internet you must configure your broadband router to

allow incoming data traffic to the network camera. To do this, enable the NAT-traversal feature, which

will attempt to automatically configure the router to allow access to the network camera. This is

enabled from Setup > System > Network > NAT.

For more information, please see “3.5.5 System>Network>NAT”of User’s Manual.

3.3 Setting the admin password over a secure connection

To gain access to the product, the password for

the default administrator user must be set. This is

done in the “Admin Password” dialog, which is

displayed when the network camera is accessed

for the setup at the first time. Enter your admin

name and password, set by the administrator.

Note: The default administrator username and

password is “admin”. If the password is lost, the

Network Camera must be reset to the factory

default settings. See “3.6 Resetting to the Factory

Default Settings”.

3.4 Live View Page

The live view page comes in several

screen modes: 1920x1080, 1280x1024,

1280x720, 704x480(576), 640x480,

352x240(288), and 320x240. Users are

allowed to select the most suitable one out

of those modes. Please, adjust the mode in

accordance with your PC specifications

and monitoring purposes.

1) General controls

Live View Page Search & Playback Page Setup Page Help Page

The video drop-down list allows you to select a customized or pre-programmed

video stream on the live view page. Stream profiles are configured under Setup > Basic

Configuration > Video & Image. . For more information, please see “3.5.1 Basic Configuration >

Video & Image”of User’s Manual.

The resolution drop-down list allows you to select the most suitable one

out of video resolutions to be displayed on live view page.

The protocol drop-down list allows you to select which combination of

protocols and methods to use depends on your viewing requirements, and on the properties of

your network.

2) Control toolbar

The live viewer toolbar is available in the web browser page only. It displays the following buttons:

The Stop button stops the video stream being played. Pressing the key again toggles the

start and stop. The Start button connects to the network camera or start playing a

video stream.

The Pause button pause the video stream being played.

The Snapshot button takes a snapshot of the current image. The location where the

image is saved can be specified.

The digital zoom activates a zoom-in or zoom-out function for video image on the live

screen.

The Full Screen button causes the video image to fill the entire screen area. No other

windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full

screen view.

The Manual Trigger button activates a pop-up window to manually start or stop the event.

The Remote Focus button enables users to adjust focus and zoom remotely via network.

The Smart Focus button readjusts focus automatically.

Use this scale to control the volume of the speakers.

Use this scale to control the volume of the microphone.

Use this scale to control the volume of the speakers and microphones.

3) Video and Audio Streams

The network camera provides several images and video stream formats. Your requirements and

the properties of your network will determine the type you use.

The Live View page in the network camera provides access to H.264, MPEG-4 and Motion JPEG

video streams, and to the list of available video streams. Other applications and clients can also

access these video streams/images directly, without going via the Live View page.

4) Focus and Zoom Control

You can control Zoom and Focus in the live screen. Press the button on the left top in the live

screen to activate the Zoom & Focus control panel.

•Adjusting Zoom:

Click “<” button to zoom out and click “>” button to zoom in. The focus is moved slightly after

adjusting zoom; adjust the focus again, as necessary.

•Adjusting Focus:

Click “>” button for far focus and click “<” button to near focus.

•Fine Focus:

Click “Fine Focus” to fine tune and readjust focus automatically.

Note: Click the button in the live screen to set the focus to the optimum position.

Table des matières

Autres manuels Vista Caméra de sécurité

Vista

Vista VK2-HD30IR-PM Manuel utilisateur

Vista

Vista VK2-1080VFDIR37e Manuel utilisateur

Vista

Vista ViP2 VK2-1080VFD Manuel utilisateur

Vista

Vista VK2-12MP360EXTIR Manuel utilisateur

Vista

Vista VP960H Manuel utilisateur

Vista

Vista VK2-108VRDIR37e Manuel utilisateur

Vista

Vista VBC400-600 Manuel utilisateur

Vista

Vista powerdome pro series Manuel utilisateur

Vista

Vista VK2-108VRDIR35V16e Manuel utilisateur

Vista

Vista VK2-1080BXDNe Manuel utilisateur

Vista

Vista VK2-108VFDIR37e Manuel utilisateur

Vista

Vista VBC28V12DN960H Manuel utilisateur

Vista

Vista VC200 Series Manuel utilisateur

Vista

Vista Onvif VK2-1080XPTZ Manuel utilisateur

Vista

Vista VFD4V9Me Manuel utilisateur

Vista

Vista VPM8030 Manuel utilisateur

Vista

Vista VK2-3MPBIR3V9F Manuel utilisateur

Vista

Vista Onvif VK2-1080XPTZ Manuel utilisateur

Vista

Vista VPC9032/CM Manuel utilisateur

Vista

Vista VK2 Series Manuel utilisateur

Vista

Vista VPC5-704DNS Manuel utilisateur

Vista

Vista VIP Series Manuel utilisateur

Vista

Vista VK2-1080XIRPTZF Manuel utilisateur

Vista

Vista VK2-1080BIR35V16e Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur