Vision ZA1502IN-7 Manuel utilisateur

www.visionsecurity.com.tw

Installation & Operation Manual

Product Description and Specification:

Limited Warranty

Vision Guarantees that every wireless 2 in 1 Universal Remote is free from

physical defects in material and workmanship under normal use for one

year from the date of purchase. If the product proves defective during this

one-year warranty period, Vision will replace it free of charge. Vision does

not issue any refunds. This warranty is extended to the original end user

purchase only and is not transferable. This warranty does not apply to: (1)

damage to units caused by accident, dropping or abuse in handling, or any

negligent use; (2) units which have been subject to unauthorized repair,

taken apart, or otherwise modified; (3) units not used in accordance with

instruction; (4) damages exceeding the cost of the product; (5) transit

damage, initial installation costs, removal cost, or reinstallation cost. For

information on additional devices, please visit us at

www.visionsecurity.com.tw

Federal Communications Commission Statement

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

FCC Caution

“the user that changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate

the equipment.”

FCC Statement in User’s Manual (for calss B) FCC Section 15.105

“Federal Communications Commission (FCC) Statement”

This equipment has been tested and found to comply with the limits for a

class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Z-Wave Command Classes:

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

COMMAND_CLASS_ASSOCIATION_V2

COMMAND_CLASS_BATTERY

COMMAND_CLASS_CONFIGURATION_V4

COMMAND_CLASS_DEVICE_RESET_LOCALLY

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

COMMAND_CLASS_INDICATOR_V3

COMMAND_CLASS_NOTIFICATION_V8

COMMAND_CLASS_POWERLEVEL

COMMAND_CLASS_SECURITY

COMMAND_CLASS_SECURITY_2

COMMAND_CLASS_SUPERVISION

COMMAND_CLASS_TRANSPORT_SERVICE_V2

COMMAND_CLASS_VERSION_V3

COMMAND_CLASS_WAKE_UP_V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Z-Wave S2 Support Command Classes :

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

COMMAND_CLASS_ASSOCIATION_V2

COMMAND_CLASS_BATTERY

COMMAND_CLASS_CONFIGURATION_V4

COMMAND_CLASS_DEVICE_RESET_LOCALLY

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

COMMAND_CLASS_INDICATOR_V3

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

COMMAND_CLASS_NOTIFICATION_V8

COMMAND_CLASS_POWERLEVEL

COMMAND_CLASS_VERSION_V3

COMMAND_CLASS_WAKE_UP_V2

ZA 1502-7 V0 1091224

2 in 1 Universal Remote

ZA1502IN-7

ZA1502EU-7

ZA1502RU-7

ZA1502US-7

ZA1502IL-7

ZA1502KR-7

ZA1502HK-7

ZA1502JP-7

ZA1502BR-7

Specification: Package Content

Protocol: Z-Wave™ (ZGM130S)

Frequency Range:

1pc ZA1502-7

1pc Operation manual

(ZA1502IN-7)

(ZA1502EU-7)

(ZA1502RU-7)

(ZA1502US-7)

(ZA1502IL-7)

(ZA1502KR-7)

(ZA1502HK-7)

(ZA1502JP-7)

(ZA1502BR-7)

923

926

865

868

869

908

916

919

922

921

MHz

Operating Range: Up to 100 feet line of sight

Operating Temp.: -10°C~ 60°C (14°F ~140°F)

System (0x09) Heartbeat (0x05)

Timer Ended (0x02)

Contact Medical Service (0x03)

Clock (0x0B)

Emergency (0x0A)

Movement

Synchronic Time

Button Press

Notification V8

Type:

TYPE EVENT

(Table 1)

0x09 0xFF

0x00

0xFF

0x09

0x0A

Movement

Synchronic Time

Button Press

V1 Alarm:

TYPE VALUE

(Table 2)

Configuration

Command Class:

BYTE VALUE Default

(Table 3) Parameter 1 1 ~ 127 (Set up from 16

to 2032 seconds) 4 (= 16 seconds x 4)1

Remark:

1. This is the definition how soon ZA1502-7 will contact Gateway after a movement behavior for triggering the

device and having a synchronic information. The basic interval time is 16 seconds, the synchronic time will be

the basic interval time by Parameter 1’s value.

2. The battery life will be shorter if the synchronic time is quicker.

Introduction

Thanks for choosing the Vision’s wireless 2 in 1 Universal

Remote (ZA1502-7) of the home security device. This sensor

is a Z-Wave Plus™. enabled device (interoperable, two-way

RF mesh networking technology) and is fully compatible with

any Z-Wav enabled network and its security framework. Every mains

powered Z-Wave PLUS™ enabled device acts as a signal repeater and

multiple devices result in more possible transmission routes which helps

eliminate “RF dead-spots”

Z-Wave Plus™. enabled devices displaying the Z-Wave Plus™. logo can also

be used with it regardless of the manufacturer, and ours can also be used in

other manufacturer’s Z-Wave Plus™. enabled networks. ZA1502-7 is an

Arrival sensor combines a unique button whose function can be defined as

one of below:

- Scene Control - Arm/Disarm

- On/Off Control - Emergency Help

When the device is secure included into Z-Wave network, above communica-

tion will be encrypted. ZA1502-7 supports SECURITY S0 / SECURITY S2

UNAUTHENTICATED / SECURITY S2 AUTHENTICATED.

3For “Inclusion” in (adding to) a network: Put the Z-Wave™ Interface

Controller into “inclusion” mode, and following its instruction to add the

ZA1502-7 to your controller. To get in the “inclusion” mode, quick press

the button of ZA1502-7 5 times for sending the NIF, the Red/Green LED

will flash 5 times quickly before the learning process for showing the

sensor has not been included. After sending NIF, Z-Wave will send the

auto inclusion, the Red/Green LED will flash 1 second after successful

inclusion; otherwise, ZA1502-7 will go to sleep after 30 seconds. The

red LED will be flashing while the inclusion is proceeding.

4For “Exclusion” from (removing from) a network: Put the Z-Wave™

Interface Controller into “exclusion” mode, and following its instruction to

delete the ZA1502-7 from your controller. Quick press the button of

ZA1502-7 5 times to be excluded, the Red/Green LED will flash 5 times

quickly after successful exclusion.

Note: All user and network settings will be cleared and the device reset

to factory defaults when the device is excluded.

5Trigger Response:

- Movement: The sensor will send Notification Report (refer to Table 1 &

2) if it has been moved.

- Synchronic Time: The sensor will send Notification Report (refer to

Table 1 & 2) and exceed the preset synchronic time (refer to Table 3).

- Button Press: Press the button of ZA1502-7 once for sending Notifica-

tion Report (refer to Table 1 & 2) if button has been pressed for any

specific purpose.

6Wake Up Notification:

Press the button of ZA1502-7 2 times will active the “Wake Up Mode” for

receiving all the command class from controller. The ZA1502-7 will go to

sleep mode without receiving any Z-Wave command till 10 seconds. It

will proceed all the commands after sending the “Wake Up Notification”

7Auto Wake Up:

Use “Wake Up” command to set up the awaking interval and send the

wake up notification to controller. User can use “Wake_Up” command

to change the auto wake up interval from 10 minutes to 1 week, Interval

increment is 200 seconds. (Default Value: 24 hours.)

8Battery Capacity Detection:

Use “Battery Get” command to have the battery capacity back in %. It

will detect the battery capacity automatically. Low Battery Auto Report

(low battery is set as 2.2+/-0.1 Voltage).

9Association:

* Support one group with 1 node.

* Group 1 = Lifeline (Battery, Notification, Reset Locally)

10 Support Explorer Frame Function

11 All the rest commands depend on Z-Wave standard

12 Factory Default Reset:

Quick press the button of ZA1502-7 4 times with another press and hold

the button around 5 seconds until the Red LED is on to send the “Device

Reset Locally Notification” command and reset to the factory default.

(Remark: This is to be used only in the case of primary controller being

inoperable or otherwise unavailable.)

13 Support OTA Firmware update from controller. Please refer to your

controller manual. Once OTA function success, we recommend you

exclusive the device & inclusive again before use the device.

14 Support SECURITY S0, SECURITY S2 UNAUTHENTICATED &

SECURITY S2 AUTHENTICATED.

15 Support SmartStart, please scan the QR Code from ZA1502-7 for

SmartStart. QR code and PIN is located on the device, also there is a

Full DSK string on the enclosed DSK card. Please keep DSK card

carefully for future inclusion needed.

(P.S.: Z-Wave SmartStart aims to shift the tasks related to inclusion of

an end device into a Z-Wave network away from the end device itself,

and towards the more user-friendly interface of the gateway.)

16 The DSK label will on the backside of ZA1502-7, Scan the DSK label to

access the SmartStart if gateway 's UI supports SmartStart. (Remark:

The QR code is for use with Z-Wave SmartStart by using “DSK,”

“Device Specific Key,” “PIN,” or “PIN code,” etc.)ateway.)

17 Enable/ Disable SmartStart:

Press the button of ZA1502-7 3 times continuously and hold the button

around 5 seconds until the Red LED and Green LED is flashing sequen-

tially. Enable and Disable is under a circle switching.

The default status is “Enable” after every time’s power on.

P.S.: The LED indicator for Enable / Disable SmartStart:

- Enable: One time’s LED flashing. (Red → Green)

- Disable: Two times’ LED flashing. (Red → Green → Red → Green).

18 A Security Enabled Z-Wave Controller must be used to fully utilize the

products.

1Green LED turns on while pressing the button of ZA1502-7.

2Quick press the button of ZA1502-7 5 times for showing the sensor’s

inclusion status.

- Not Included : Red/Green LED flashing 5 times quickly.

- Included : Red/Green LED flashing 1 second.

Notice: If you are installing the entire Z-Wave™ system for the

first time, please refer to the installation guide of Z-Wave™

Interface Controller and full charging the ZA1502-7 before using.

Operation

Button

ZA 1502-7

Ce manuel convient aux modèles suivants

Autres manuels Vision Télécommande universelle

Vision

Vision ZA1502IN-7 Manuel utilisateur

Manuels Télécommande universelle populaires d'autres marques

Pronto

Pronto Peel Manuel utilisateur

GE 24929 Manuel utilisateur

Radio Shack

Radio Shack Wireless Remote Control System Manuel utilisateur

AUVIO

AUVIO Universal Home Theater Remote Manuel utilisateur

Philips

Philips Icon SRU4106 Manuel utilisateur

THOMSON

THOMSON ROC4309 Manuel utilisateur

Philips

Philips pm625S Manuel utilisateur

GE RM94931 Manuel utilisateur

RCA

RCA RCU600WMS - Universal Remote Control Manuel utilisateur

Blackweb

Blackweb BWB17AV002 Manuel utilisateur

Marmitek

Marmitek DoorGuard 300 Manuel utilisateur

Chunghop

Chunghop RM-L618 Manuel utilisateur

GE RM24965 Manuel utilisateur

Anderic

Anderic KTN828 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Manuel utilisateur

Medion

Medion E74023 Manuel utilisateur

intensity

intensity RM02A Manuel utilisateur

GE RM24950 Manuel utilisateur