Vision Datum LEO Series Manuel utilisateur
LEO 10GigE Area Scan User Manual 2
1
Copyright ©2022
Hangzhou Vision Datum Technology Co., Ltd.
Tel.: 0571-86888309
Add.:C-5F, No. 8 Xiyuan 9th Road, West Lake District Hangzhou Zhejiang 310030 China.
All rights reserved. The information contained herein is proprietary and is provided solely for the purpose of allowing customers to
operate and/or service Vision Datum manufactured equipment and is not to be released, reproduced, or used for any other purpose
without written permission of Vision Datum.
Disclaimer
The information and specifications described in this manual are subject to change without notice.
Latest Manual Version
For the latest version of this manual, see the Download Center on our web site at:：www.visiondatum.com
Technical Support
For technical support, e-mail：[email protected].
Warranty
To ensure that your warranty remains in force, adhere to the following guidelines:：
Do not remove the camera’s serial number label
If the label is removed and the serial number can’t be read from the camera’s registers, the warranty is void.
Do not open the camera housing
Do not open the housing. Touching internal components may damage them.
Prevent ingress or insertion of foreign substances into the camera housing
Prevent liquid, flammable, or metallic substances from entering the camera housing. If operated with any foreign substances inside, the
camera may fail or cause a fire.
Avoid electromagnetic fields
Do not operate the camera in the vicinity of strong electromagnetic fields. Avoid electrostatic charging.
Clean with care
Avoid cleaning the sensor if possible.
Handle this camera with care
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handling.
Read the manual
Read the manual carefully before using the camera.
Preface
Preface
Purpose
This Manual is a basic description of LEO series 10GigE Area Scan Cameras, which mainly includes the product description,
quick installation guide and Simple introduction of SDK(iDatum). This manual may be updated due to product upgrades or
other reasons. If you need, please contact the sales engineer for the latest version of this manual.
3LEO 10GigE Area Scan User Manual
1 1
Product
Description
1
CHAPTER 1 PRODUCT DESCRIPTION
Product Introduction
LEO series industrial cameras compatible with GigE、10GigE、USB3.0 and Cameralink data bus standards, support GenICam、
USB3 Vision® and GigE Vision®, Smoothly connect with third-party software, like HALCON and Vision Pro, not need for secondary
development. LEO series cameras with excellent cost performance and very suitable for various inspections measurement and high-
speed imaging applications. This series cameras won customers high praise because its outstanding performance in cellphone and
tablet PC screen inspection, LED automatic packaging, defect inspection, and electronic components manufacturing, wafer positioning
and other applications.
With this variety of sensors and interfaces, combined with the extensive features offered, LEO series cameras are fit for a wide range of
vision applications.
Product Features
■ 10 Gigabit Ethernet interface, compatible with Gigabit Ethernet, with maximum 100m transmission；
■ 1024MB on-board frame buffer for data transmission and image retransmission；
■ Supports software trigger, hardware trigger, free run mode and etc；
■ Supports sharpness, gamma correction, LUT, black level correction and other ISP function；
■ Supports interpolation algorithm, white balance algorithm, color conversion matrix, hue,saturation and etc. for color camera；
■ Supports various output formats for image data and supports ROI, binning, mirror and etc；
■ Conforms GigE Vision protocol and GenICam standards；
■ Support third-party software connection.
＊ The camera functions may differ by camera models,please refer to actual functions.
Status LED Description
Status LED Description
Slow Flashing Red
(the interval between on and off is 2000 milliseconds) The camera wiring exception occurs.
Red light is always on The camera exception occurs.
Blue light is always off The camera is in idle status.
Fast Flashing Blue
(the interval between on and off is 200 milliseconds) The camera is acquiring images normally.
Slow Flashing blue
(the interval between on and off is 1000 milliseconds) The camera is acquiring images in trigger mode.
Flashing Alternately Red and Blue _The firmware is updating.
_The function of finding me is executed,
LEO 10GigE Area Scan User Manual 4
1
Product
Description
Mechanical Dimensions
The dimensions is in millimeters：
The cameras are interfaced to an external circuity via connectors located on the back of the housing.
■ Mechanical Dimensions (in mm) of LEO 12MS-68tgm(V2) 10GigE Cameras with M58 Mount (With fan,the installation use M3 screws).
74
74
60
4-M3x5
60
24.5
24.5
5.6
4-M3x3
OPTICALDISTANCE
11.48 -0.15
+0.05 20
2-M2x4
46.6
74.4
M58*0.75
■ Mechanical Dimensions (in mm) of LEO 25MP-40tgm/tgc 10GigE Cameras with M58 Mount (With fan,the installation use M3 screws).
M58 X0. 75
74
74
60
4-M3 5
60
24.5
24.5
3. 88
3
4-M3
20
42-M2
44 .88
72 .7
OPTICALDISTANCE
11 .48-
+
0
0
.
.
15
05
■ Mechanical Dimensions (in mm) of LEO 24MS-35Tgm 10GigE Cameras with C-mount (With heat sink,the installation use M4 screws).
84
84
62
62
5.1
62 .5
30
60
92 .5
17 .52 +
-
0
0
.
.
05
15
OPTICAL DISTANCE
1- 32 UNFx8
4-M4x5
20 2-M2x4
4-M4x5
5LEO 10GigE Area Scan User Manual
1 1
Product
Description
Mechanical Dimensions
■ Mechanical Dimensions (in mm) of LEO 25MP-40tgm/tgc 10GigE Cameras with F Mount (With fan,the installation use M3 screws).
24.5
24.5
8.88
50.88
4-M3 x3
113
46.5
-0.15
+0.05
81.88
74
74
60
4-M3 x5
60
20
2-M2 x4
■ Mechanical Dimensions (in mm) of LEO 25MD-30Tgm 10GigE Cameras with M58 Mount (With fan,the installation use M3 screws).
■ Mechanical Dimensions (in mm) of 25MG-40tgmTgc 10GigE Cameras with M58 Mount (With fan,the installation use M3 screws).
24 .5
32-M3
74
60
74 51
78 .8
3.7
60
5
4-M3 M58X 0.75 OPTICAL DISTANCE
11 .48 -
+
0
0
.
.
15
05
20
4
2-M2
74
60
60
74
M58× 0. 75
64-M3
51
78 .8
34-M3
24 .5
3.7
OPTICAL DISTANCE
11 .48 +
-
0
0
.
.
05
15
LEO 10GigE Area Scan User Manual 6
1
Product
Description
Mechanical Dimensions
■ Mechanical Dimensions (in mm) of LEO 65MG-15tgm/tgc 10GigE Cameras with M58 Mount (With fan,the installation use M3 screws).
■ Mechanical Dimensions (in mm) of LEO 65MG-15tgm/tgc 10GigE Cameras with F Mount (With fan,the installation use M3 screws).
74
60
74
60
24 .5
10
84 .8
56 .99
5
4-M3
34-M3
46 .5 -
+
0
0
.
.
15
05
20
4
2-M2
24 .5
34-M3
74
60
74 51
78 .8
60 3.7
5
4-M3 M58X 0. 75
11 .48-
+
0
0
.
.
15
05
20
4
2-M2
■ Mechanical Dimensions (in mm) of LEO 150MS-6tgm 10GigE Cameras with M72 Mount (TEC cooling,the installation use M4 screws).
7.5 24 .5
107
64-M4
19 .5 5 -
+0
0.
.15
05
120
120
107 5M72× 0. 75
89
4-M4
74
5
LEO 10GigE Area Scan User Manual 7
2
Power and
I/O Interface Definition
1 2
CHAPTER 2
POWER AND
I/O IENTERFACE DEFINITION
I/O Connection Definition and Assignments
Read the followings to get pin definitions.Refer to the pin definitions and labels attached to the power and I/O cable to wire the device.
78
9
1
2
3
4
5
6
11
10
12
Table 2-1:
Numbering and assignments for
12pin Power and I/O Input Connector:
(M58/F-mount 10GigE camera)
Pin Signal I/O Signal Source Designation
1 GND DC ground Camera Power Supply Ground
2 DC_PWR DC_PWR + DC Camera Power
3 - - -
4- - -
5GND_IO Line 0/1- Opto-isolated Signal Ground
6 - - -
7- - -
8 RS232_RX 232 serial port input RS232 Received Data
9 RS232_TX 232 serial output RS232 Transmitted Data
10 GPIO Line 2+ Can be Configured as Input or Output
11 OPTO_OUT Line 1+ Opto-isolated OUT
12 OPTO_IN Line 0+ Opto-isolated IN
78
9
1
2
3
4
5
6
11
10
12
Table 2-2:
Numbering and assignments for
12pin Power and I/O Input Connector:
(M72-mount 10GigE camera)
Pin Signal I/O Signal Source Designation
1 GND Line 2- Camera Power Supply Ground
2 DC_PWR - DC Camera Power
3 DC_PWR - DC Camera Power
4OPT_IN- Line 0- Opto-isolated IN Signal Ground
5OPT_OUT- Line 1- Opto-isolated output signal ground
6 GND - DC Camera Power
7 GND - DC Camera Power
8 232_RXD - RS232 Received Data
9 232_TXD - RS232 Transmitted Data
10 GPIO2 Line 2+ Can be Configured as Input or Output
11 OPTO_OUT+ Line 1+ Opto-isolated OUT
12 OPTO_IN+ Line 0+ Opto-isolated IN
LEO 10GigE Area Scan User Manual 8
32
Power and
I/O Interface Definition
NOTICE
An incorrect plug can damage the I/O connector.
The plug on the cable that you attach to the camera’s I/O connector must have 12 female pins. Using a plug designed for a
smaller or a larger number of pins can damage the connector
Vision Datum offers suitable plugs and cables.
Contact your sales representative to order connectors or cables.
i
Cable
Recommendations for using Network cables：
■ 10 Gigabit RJ-45 port camera,It refers to CAT-6e network cable or above. You need to purchase separately.
■10 Gigabit optical fiber port camera,It refers to the optical fiber and you should select it according to the camera’s optical
module. You need to purchase separately.
10 GigE NIC：RJ-45-port camera needs to be equipped with 10 GigE NIC;It refers to the 10 GigE network interface card. You
need to purchase separately.
Optical Module：10 Gigabit optical fiber port camera needs to be equipped with optical module for photoelectric signal
conversion,It includes single module or multiple modules, and you should purchase it separately according to actual demands.
Recommendations for using I/O cables：
■I/O cables must be shielded.
■ Use twisted pair cables.
■Recommended maximum cable length: 10 m.
■Pin assignments (refer to Tables 2-1/2-2).
■Avoid strong magnetic fields.
Depending on the particular application, using different cables may lead to voltage drops, signal distortion, and EMI/ESD problems
which in turn may cause the camera to malfunction.
Note that direct-coupled GPIO lines have the advantage of working with very short delays compared to opto-isolated
I/O lines.
Note also that the direct-coupled GPIOs are distinctly more susceptible to EMI than the opto-isolated I/Os. Under
harsh EMI conditions, GPIOs can turn out not to be usable at all.
Accordingly, use of the GPIOs in an environment with elevated risk of EMI calls for taking additional measures like, e.g.
using shorter cables.
i
I/O Connection Definition and Assignments
9LEO 10GigE Area Scan User Manual
3 3
Installation
and Setup
2
Power and
I/O Interface Definition
3
CHAPTER 3 INSTALLATION AND SETUP
Installation and Setup
You should perform the software installation procedure first and the hardware installation procedure second.
Software Installation
iDatum Installation
System Requirements
LEO Camera Software Suite for Windows requirements that one of the following operating systems is installed on your computer：
■ Windows XP (32 bit)
■ Windows 7 (32 bit or 64 bit)
■ Windows 10 (32 bit or 64 bit)
■ Linux 32 Bit/64 Bit : Ubuntu 14.04(32/64)、Ubuntu 16.04(32/64)、 Redhat7(64)、Centos7(32/64)、gcc/g++ version requires 4.6.3
and above
■ ARM: NVIDIA TX2、RaspberryPiB3.0+
Installation Steps
1.You can download the iDatum software（LEO Series Industrial Cameras SDK For xxx）from：
http://www.visiondatum.com/en/service/005001.html
2.Double click iDatum installation package to install the client.
3.Follow the instructions on the screen. The installer will guide you through the installation process.
If you use a firewall on your computer, disable the firewall for the network adapter to which your camera is connected.
Close the Firewall
In order to ensure the camera software keep running and image transmission stability, please close the firewall before using
the software.
Environment Testing
After successful installation, please connect the camera and turn on iDatum client software to check the result of camera
connection and image preview. You can start secondary development base on the SDK when all environment testing is normal.
You should notice follow items when using GigE Camera：
■ FrameRate Whether the frame rate is consistent with the actual set frame rate.
■ Errors If not 0, it means there is a frame skip, it is abnormal.
■ Lost Packets If not 0, it is abnormal.
LEO 10GigE Area Scan User Manual 10
3
Installation
and Setup
Hardware Installation
Camera Installation
The installation procedures assume that you will be making a peer-to-peer connection between your camera and a
computer.
Make sure that the following items are available before starting the installation：
■ LEO 10GigE Area scan camera
■ Applicable power supply or a 10Gigabit Ethernet Switch
■ It refers to the lens that matches with lens mount of the camera.
■ The computer with a GigE network adapter installed
■ The computer must be equipped with appropriate operating system
■ Use a suitable network cable to connect the camera to a 10 GigE or a 10 GigE NIC or a 10 GigE optical NIC.
Steps：
■ Mount lens that matches with lens mount of the camera
■ Connect the camera to the computer and power
12-pin:
● Use a network cable to connect the camera to a network interface card.
● Use the 12-pin power and I/O cable to connect the camera to a power adapter.
Network Settings
Before using the camera, you need to configure IP is in the same network segment with the computer. You can modify it in “Local
Connection” to ensure network communication is normal.
Local Network Configuration
● Click “Control Panel”> “Network and Internet”> “Network and Sharing Center”> “Change Adapter Configuration. “Then
select corresponding network card to configure it automatically obtain IP address or manually assign it as same network
segment address with the camera. Shown as below:
● Open “Advanced” in the properties, set “Jumbo Frame” as its maximum value:9014bytes, both of transmit buffer and receive
buffer set as 2048bytes, the Interrupt Throttle Rate set as extremum value. These maximum values mentioned above depend on
the specific network card. Shown as below:
Autres manuels pour LEO Series
1
Table des matières
Autres manuels Vision Datum Appareil photo numérique
