Viper 106V Manuel utilisateur
© 2004 Directed Electronics, Inc. Vista, CA N106V 08-04
110066VV
IInnssttaallllaattiioonnGGuuiiddee
contents
what is included . . . . . . . . . . . . . .3
system configuration . . . . . . . . . .3
wire connection guide . . . . . . . . .4
immobiliser harness wiring
diagram . . . . . . . . . . . . . . . . . .4
power harness wiring diagram .4
touch-key harness wiring
diagram . . . . . . . . . . . . . . . . . .5
immobiliser harness wiring
guide . . . . . . . . . . . . . . . . . . . .6
power harness wiring guide . . .6
touch-key receptacle wiring
guide . . . . . . . . . . . . . . . . . . . .7
passenger compartment . . . . . . . .7
mounting the control unit . . . . .7
programming instructions . . . . .8
certificate of installation . . . . . . .8
troubleshooting . . . . . . . . . . . . . .8
wiring reference guide . . . . . . . . .9
notes . . . . . . . . . . . . . . . . . . . . . .10
Clifford®, Code-Hopping™, Directed®, Valet®are all Trademarks or Registered Trademarks of Directed Electronics, Inc.
IIMMPPOORRTTAANNTT!!The Viper 106V system is designed to be installed in any
petrol or common rail diesel vehicle with a 12-volt battery.
© 2004 directed electronics, inc. 3
what is included
zOne control module with 9-wire immob- zOne Owner’s Guide
iliser harness
z2-Touch-keys zTwo window decals
zTouch-key receptacle with LED zOne hardware pack
system configuration
The Viper 106V system has a control module which works in conjunction with a touch-
key to allow the vehicle to be started. A total of 3 touch-keys can be programmed into
the control module.
NNOOTTEE::The touch-key receptacle must be installed so that the
LED is visible to the vehicle operator when using the touch-key.
TOUCH-KEY RECEPTACLE LED
TOUCH-KEY
www.directed.com
4
wire connection guide
immobiliser harness wiring diagram
___
___
___
___
___
___
power harness wiring diagram
___
___
___
NNOOTTEE::Please remove all wire description tags from wiring after
connection to the vehicle.
GND2 (Ground 2)
GND1 (Ground 1)
+12V
1
2
3
NNOOTTEE::All wires are BLACK. Each wire is marked with its function.
The description listed below is the marking on each wire and then
its function, in brackets.
IGN: Ignition Side (Ignition Interrupt Com)
STR: Key Side (Starter Interrupt 87)
Fuel Pump Input (Fuel Pump Interrupt 87)
IGN: Key Side (Ignition Interrupt 87)
STR: Starter Side (Starter Interrupt Com)
Fuel Pump Output (Fuel Pump Interrupt Com)
1
2
3
4
5
6
NNOOTTEE::All wires are BLACK. Each pair is an immobiliser circuit
input and output. Each wire is marked with its function. The descrip-
tion listed below is the marking on each wire and then its function,
in brackets.
© 2004 directed electronics, inc. 5
touch-key harness wiring diagram
___
___
___ LED +2V
Ground
Data
1
2
3
NNOOTTEE::All wires are BLACK. Each wire is marked with its func-
tion. The Touch-Key harness has 3-pin connectors to facilitate
the connection from the control module to the Touch-Key recep-
tacle. The functions are listed below for reference only.
www.directed.com
6
immobiliser harness wiring guide
This guide describes in detail the connection of each wire. Please read the instructions
carefully to ensure a thorough understanding of this unit and how it operates. Locate
the main ignition, starter and fuel pump circuit wires with a multimeter. Cut the appro-
priate wire and attach the key side and car side wires to the corresponding wires on
the 6-wire immobiliser harness.
IGN: Key Side
This wire is connected to the ignition key side of the ignition circuit. This wire should
be +12volt with the ignition turned on and in the cranking position.
IGN: Ignition Side
Connect this wire to the ignition output side of the ignition circuit.
STR: Key Side
This wire is connected to the starter key side of the starter solenoid.
STR: Starter Side
Connect this wire to the starter solenoid side of the starter circuit.
Fuel Pump Input
This wire is connected to the input side of the fuel pump circuit or ground if not used.
Fuel Pump Output
Connect this wire to the fuel pump output high polarity side of the fuel pump circuit or
ground if not used.
power harness wiring guide
+12V
Connect the +12V wire via fuse supplied to an unfused source at the vehicle's fuse-
box.
GND1 and GND2
Connect the BLACK wires (2 and 3) to separate ground locations using a factory bolt
that does NOT have any vehicle component grounds attached to it or drill a new hole
if required. A screw should only be used in conjunction with a two-sided lock wash-
er. Under dash brackets and door sheet metal are not acceptable ground points.
© 2004 directed electronics, inc. 7
touch-key receptacle wiring guide
Mount the touch-key receptacle in a position accessible to the operator of the vehicle
and so that the LED is visible to the operator. A bracket is provided to allow an addi-
tional mounting method if required.
Plug the touch-key receptacle harness into the wire harness plug from the control mod-
ule.
passenger compartment
mounting the control unit
Select an area behind the dash that will allow you to securely fasten the unit using the
screws provided in the hardware pack. Do not mount the unit near moving parts or
in direct path of air blowing from the heater vents.
NNOOTTEE::When mounting the control module the metal enclosure
must be used.
NNOOTTEE::The Viper 106V control unit must be installed inside the
vehicle. Under no circumstances should the unit be installed
under the bonnet or other similarly hostile environment.
NNOOTTEE::Please remove all wire description tags from wiring after
connection to the vehicle.
www.directed.com
8
programming instructions
Use the procedure below to program touch-keys into the system. A maximum of 3
touch-keys can be programmed into the system.
1. Turn the ignition On then Off 12 times.
2. The LED will illuminate continuously.
3. Insert the touch-key to be programmed into the touch-key receptor.
4. The LED will turn Off for 1-second and then back On continuously. The touch-
key is now programmed.
5. After 15 seconds of no activity the LED will extinguish and the system will exit the
programming routine.
certificate of installation
After installation you must fill out the certificate of installation. Once you have filled
out all information on the certificate the customer must sign and date it. Distribute the
copies as follows:
zWhite (top) copy - customer
zBlue copy - customer’s insurance broker
zPink copy - Directed Electronics, UK office
zGreen copy - installing dealer
troubleshooting
The Touch-Key does not work.
zMake sure that the harness is plugged in. (Refer to the wiring reference guide.)
zHas the Touch-Key been programmed to the system.
The system does not work (no LED illumination).
zCheck the fuse in the power harness.
NNOOTTEE::If more than one touch-key is required to be programmed,
then repeat steps 3 and 4 after the first touch-key is programmed.
NNOOTTEE::In order to program touch-keys into the system, the sys-
tem must be disarmed.
© 2004 directed electronics, inc. 9
wiring reference guide
NNOOTTEE::Please remove all wire description tags from wiring after
connection to vehicle.
NNOOTTEE::The current draw for the entire system is less than 9 mA. Power
supply voltage range is 9 to 16 volts. The current handling capacity for
each immobilisation circuit is 20amps continuous/30amps peak.
106V
BATTERY
FUSE BOX +-
TOUCH-KEY
3-PIN
GND1
GND2
+12V
FUEL PUMP
KEY ON
CUT FUEL PUMP OUTPUT
FUEL PUMP INPUT
POWER HARNESS
TOUCH-KEY HARNESS
IMMOBILISER HARNESS
CONNECT TO 2
SEPARATE GROUNDS
FUEL PUMP (OPTIONAL)
GROUND BOTH OF THE
WIRES FROM THE 106V
IF NOT USED.
IGNITION
SWITCH
CUT
IGNITION
IGN: IGNITION SIDE
IGN: KEY SIDE
CUT
STR: KEY SIDE
STR: STARTER SIDE
STARTER
www.directed.com
10
notes
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
________________________________________
Table des matières
Autres manuels Viper Alarme de voiture
Viper
Viper 5706V Manuel utilisateur
Viper
Viper 130XV Manuel utilisateur
Viper
Viper 791 XV Manuel utilisateur
Viper
Viper 791 XV Manuel utilisateur
Viper
Viper 5706V Manuel utilisateur
Viper
Viper 5901 Manuel utilisateur
Viper
Viper 4115V Manuel utilisateur
Viper
Viper Directed 4706V Manuel utilisateur
Viper
Viper 5806V Manuel utilisateur
Viper
Viper 5901 Manuel utilisateur
Viper
Viper 500HF Manuel utilisateur
Viper
Viper 460XV Manuel utilisateur
Viper
Viper 4708V Manuel utilisateur
Viper
Viper SmartKey VSK100 Manuel utilisateur
Viper
Viper 300+ Manuel utilisateur
Viper
Viper 300 ESP Manuel utilisateur
Viper
Viper 310V Manuel utilisateur
Viper
Viper Responder 350 Manuel utilisateur
Viper
Viper 3606V Manuel utilisateur
Viper
Viper 426FS Manuel utilisateur
Manuels Alarme de voiture populaires d'autres marques
Clifford
Clifford 3606X Manuel utilisateur
Ultra Start
Ultra Start 2500M SERIES Manuel utilisateur
Ultra Start
Ultra Start 650 Series Manuel utilisateur
Audiovox
Audiovox Prestige Platinum+ APS-511C Manuel utilisateur
Sparkrite
Sparkrite SRA8 Manuel utilisateur
Federal Signal Corporation
Federal Signal Corporation Pathfinder Siren Series Manuel
Falcon
Falcon Predator XL3 Guide de l'utilisateur
Audiovox
Audiovox Auto Security XR91 Mode d'emploi
Clifford
Clifford Sabre II Manuel utilisateur
CrimeStopper
CrimeStopper CS-8717 Guide de démarrage rapide
Ultra Start
Ultra Start 450 SERIES Manuel utilisateur
Scytek electronic
Scytek electronic Vectra X3 Manuel utilisateur
