ViewSonic PJD5351LS Manuel utilisateur

PJD5351LS

DLP Projector

User Guide

Model No. VS17087

IMPORTANT: Please read this User Guide to obtain important information on installing

and using your product in a safe manner, as well as registering your product for future

service. Warranty information contained in this User Guide will describe your limited

coverage from ViewSonic Corporation, which is also found on our web site at http://

ZZZYLHZVRQLFFRP LQ(QJOLVKRULQ VSHFL¿FODQJXDJHV XVLQJWKH 5HJLRQDOVHOHFWLRQ

box in the upper right corner of our website. “Antes de operar su equipo lea cu

idadosamente las instrucciones en este manual”

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the follow-

ing two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses, and can radiate radio frequency energy, and

if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

yConsult the dealer or an experienced radio/TV technician for help.

Warning:<RXDUHFDXWLRQHGWKDWFKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHG

by the party responsible for compliance could void your authority to operate the

equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage

Directive 2014/35/EU.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic

Equipment Directive 2012/19/EU (WEEE).

The mark indicates the requirement NOT to dispose the equipment

including any spent or discarded batteries or accumulators as unsorted

municipal waste, but use the return and collection systems available.

If the batteries, accumulators and button cells included with this equipment,

display the chemical symbol Hg, Cd, or Pb, then it means that the battery

has a heavy metal content of more than 0.0005% Mercury or more than,

0.002% Cadmium, or more than 0.004% Lead.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth.

7. Do not block any ventilation openings. Install the unit in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves,

RURWKHUGHYLFHVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade and the third

SURQJDUHSURYLGHGIRU\RXUVDIHW\,IWKHSURYLGHGSOXJGRHVQRW¿WLQWR\RXU

outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs.

Convenience receptacles and the point where they exit from the unit. Be sure

that the power outlet is located near the unit so that it is easily accessible.

 2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKHPDQXIDFWXUHU

 8VHRQO\ZLWKWKHFDUWVWDQGWULSRGEUDFNHWRUWDEOHVSHFL¿HGE\

the manufacturer, or sold with the unit. When a cart is used, use

caution when moving the cart/unit combination to avoid injury from

tipping over.

13. Unplug this unit when unused for long periods of time.

 5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO6HUYLFLQJLVUHTXLUHGZKHQWKH

unit has been damaged in any way, such as: if the power-supply cord or plug is

damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed

to rain or moisture, or if the unit does not operate normally or has been dropped.

iii

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive

2011/65/EU of the European Parliament and the Council on restriction of the use

of certain hazardous substances in electrical and electronic equipment (RoHS2

Directive) and is deemed to comply with the maximum concentration values issued

by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum

Concentration

Actual Concentration

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex III

of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. 0HUFXU\LQFROGFDWKRGHÀXRUHVFHQWODPSVDQGH[WHUQDOHOHFWURGHÀXRUHVFHQW

lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):

(1) Short length (≦500 mm): maximum 3.5 mg per lamp.

(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.

(3) Long length (＞1,500 mm): maximum 13 mg per lamp.

2. Lead in glass of cathode ray tubes.

3. /HDGLQJODVVRIÀXRUHVFHQWWXEHVQRWH[FHHGLQJE\ZHLJKW

4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

5. Copper alloy containing up to 4% lead by weight.

6. Lead in high melting temperature type solders (i.e. lead-based alloys containing

85% by weight or more lead).

7. Electrical and electronic components containing lead in a glass or ceramic other

than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or

ceramic matrix compound.

Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks

of Microsoft Corporation in the United States and other countries.

ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered

trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association.

DPMS and DDC are trademarks of VESA.

PS/2, VGA and XGA are registered trademarks of International Business Machines

Corporation.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors

or omissions contained herein; nor for incidental or consequential damages resulting

from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves

WKHULJKWWRFKDQJHSURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFX-

ment may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means,

for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information

as it becomes available, please visit your region section on ViewSonic’s website to

The ViewSonic CD also provides an opportunity for you to print the product

registration form. Upon completion, please mail or fax to a respective ViewSonic

office. To find your registration form, use the directory “:\CD\Registration”.

Registering your product will best prepare you for future customer service needs.

Please print this user guide and fill the information in the “For Your Records” section.

For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name: PJD5351LS

ViewSonic DLP Projector

Model Number: VS17087

Document Number: PJD5351LS_UG_ENG Rev. 1A 06-22-17

Serial Number: ________________________________________

Purchase Date: ________________________________________

Product disposal at end of product life

The lamp in this product contains mercury which can be dangerous to you and the

environment. Please use care and dispose of in accordance with local, state or

federal laws.

ViewSonic respects the environment and is committed to working and living green.

Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic

website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/

Europe: http://www.viewsoniceurope.com/eu/support/call-desk/

Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

Table of contents

Important safety

instructions .......................2

Introduction......................4

Projector features ................................. 4

Shipping contents................................. 5

Projector exterior view......................... 6

Controls and functions ......................... 7

Positioning your projector

..........................................12

Choosing a location............................ 12

Projection dimensions........................ 13

Connection ......................14

Connecting a computer or monitor .... 15

Connecting Video source device........ 16

Using the cable management cover

(optional accessory) ........................... 16

Operation ........................18

Starting up the projector..................... 18

Using the menus................................. 19

Utilizing the password function ......... 20

Switching input signal........................ 22

Adjusting the projected image ........... 22

Magnifying and searching for details

............................................................ 23

Selecting the aspect ratio ................... 24

Optimizing the image......................... 25

Setting the presentation timer ............ 28

Hiding the image................................ 29

Locking control keys.......................... 29

Operating in a high altitude environment

............................................................ 29

Using the 3D functions...................... 30

Using the projector in standby mode

........................................................... 30

Adjusting the sound ........................... 31

Shutting down the projector .............. 31

Menu operation.................................. 32

Maintenance ...................40

Care of the projector .......................... 40

Using the dust filter (optional accessory)

........................................................... 41

Lamp information .............................. 42

Troubleshooting .............46

Specifications ..................47

Projector specifications...................... 47

Dimensions ........................................ 48

Ceiling mount installation ................. 48

Timing chart ...................................... 49

Appendix.........................52

IR control table .................................. 52

RS232 command table....................... 53

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information

technology equipment. However, to ensure safe use of this product, it is important that you

follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1. Please read this manual before you operate your projector. Save it for future

reference.

2. Do not look straight at the projector lens during operation. The intense light beam

may damage your eyes.

3. Refer servicing to qualified service personnel.

4. Always open the lens shutter or remove the lens cap when the projector lamp is

on.

5. In some countries, the line voltage is NOT stable. This projector is designed to operate

safely within a mains voltage between 100 to 240 volts AC, but could fail if power

cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate

or cut out, it is recommended that you connect your projector through a power

stabilizer, surge protector or uninterruptible power supply (UPS).

6. Do not block the projection lens with any objects when the projector is under

operation as this could cause the objects to become heated and deformed or even

cause a fire. To temporarily turn off the lamp, press BLANK on the projector or

remote control.

7. The lamp becomes extremely hot during operation. Allow the projector to cool for

approximately 45 minutes prior to removing the lamp assembly for replacement.

8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps

beyond the rated life could cause them to break on rare occasions.

9. Never replace the lamp assembly or any electronic components unless the projector is

unplugged.

10. Do not place this product on an unstable cart, stand, or table. The product may fall,

sustaining serious damage.

11. Do not attempt to disassemble this projector. There are dangerous high voltages inside

which may cause death if you should come into contact with live parts.

Under no circumstances should you ever undo or remove any other covers. Refer

servicing only to suitably qualified professional service personnel.

12. Do not place this projector in any of the following environments.

- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls

and free flow of air around the projector.

- Locations where temperatures may become excessively high, such as the inside of a

car with all windows rolled up.

- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical

components, shortening the projector's life span and darkening the picture.

- Locations near fire alarms

- Locations with an ambient temperature above 40°C / 104°F

- Locations where the altitudes are higher than 3000 m (10000 feet).

13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed,

overheating inside the projector may result in a fire.

- Do not place this projector on a blanket, bedding or any other soft surface.

- Do not cover this projector with a cloth or any other item.

- Do not place inflammables near the projector.

14. Always place the projector on a level, horizontal surface during operation.

- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of

more than 15 degrees front to back. Using the projector when it is not fully horizontal

may cause a malfunction of, or damage to, the lamp.

15. Do not stand the projector on end vertically. Doing so may cause the projector to fall

over, causing injury or resulting in damage to the projector.

16. Do not step on the projector or place any objects upon it. Besides probable physical

damage to the projector, doing so may result in accidents and possible injury.

17. Do not place liquids near or on the projector. Liquids spilled into the projector may

cause it to fail. If the projector does become wet, disconnect it from the power

supply's wall socket and call your local service center to have the projector serviced.

18. This product is capable of displaying inverted pictures for ceiling mount installation.

Use only qualified ceiling mount kit for mounting the projector and ensure it is

securely installed.

19. When the projector is under operation, you may sense some heated air and odor from

its ventilation grill. It is a normal phenomenon and not a product defect.

20. Do not use the Security bar for transporting or installation. It should be used with a

commercially available theft prevention cable.

Safety instructions for ceiling mounting of the

projector

We want you to have a pleasant experience using your projector, so we need to bring this

safety matter to your attention to prevent damage to person and property.

If you intend to mount your projector on the ceiling, we strongly recommend that you use a

proper fitting projector ceiling mount kit and that you ensure it is securely and safely

installed.

If you use an inappropriate projector ceiling mount kit, there is a safety risk that the

projector may fall from the ceiling due to an improper attachment through the use of the

wrong gauge or length screws.

You can purchase a projector ceiling mount kit from the place you purchased your projector.

We recommend that you also purchase a separate security cable and attach it securely to

both the anti-theft lock slot on the projector and the base of the ceiling mount bracket. This

will perform the secondary role of restraining the projector should its attachment to the

mounting bracket become loose.

Introduction

Projector features

The projector integrates high-performance optical engine projection and a user-friendly

design to deliver high reliability and ease of use.

The projector offers the following features.

• Dynamic mode adjusting the power consumption of the lamp according to the

brightness of the image being projected

• Power saving function decreasing the power consumption of the lamp by up to 70%

when no input signal can be detected for a set period of time.

• Presentation timer for better control of time during presentations

• Supports 3D display

•ColorManagement allowing color adjustments to your liking

• Less than 0.5W power consumption when power saving mode is turned on

• Screen Color correction allowing projection on surfaces of several predefined colors

• Quick auto search speeding up the signal detecting process

• Color modes providing choices for different projection purposes

• Selectable quick power off function

• One-key auto-adjustment to display the best picture quality

• Digital keystone correction to correct distorted images

• Adjustable color management control for data/video display

• Ability to display 1.07 billion colors

• Multi-language On-Screen Display (OSD) menus

• Switchable normal and economic modes to reduce the power consumption

The apparent brightness of the projected image will vary depending on the ambient lighting

conditions, selected input signal contrast/brightness settings, and is directly proportional to

projection distance.

The lamp brightness will decline over time and may vary within the lamp manufacturers

specifications. This is normal and expected behavior.

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these

items are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those

illustrated.

Optional accessories

1. Replacement lamp (RLC-092 for PJD5351LS.)

2. Soft carry case

3. VGA-Component adapter

4. Dust filter

5. Cable management cover

Projector Power CordVGA Cable

Quick Start Guide Remote Control & Batteries

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ViewSonic Projecteur

ViewSonic

ViewSonic PRO8450W VS13646 Manuel utilisateur

ViewSonic

ViewSonic PRO9500 Manuel utilisateur

ViewSonic

ViewSonic PX705HD Manuel utilisateur

ViewSonic

ViewSonic Pro10100 Manuel utilisateur

ViewSonic

ViewSonic PJD5523w Manuel utilisateur

ViewSonic

ViewSonic PJ452 - LCD XGA Projector-4.9LBS Manuel utilisateur

ViewSonic

ViewSonic Pro8300 Manuel utilisateur

ViewSonic

ViewSonic PJD5234L Manuel utilisateur

ViewSonic

ViewSonic PJL855 Manuel utilisateur

ViewSonic

ViewSonic PJ500-2 Manuel utilisateur

ViewSonic

ViewSonic Pro9000 Manuel utilisateur

ViewSonic

ViewSonic PA700WC Manuel utilisateur

ViewSonic

ViewSonic PJ750 Manuel utilisateur

ViewSonic

ViewSonic PJD5234 Manuel utilisateur

ViewSonic

ViewSonic PJ513D Manuel utilisateur

ViewSonic

ViewSonic PJ1065 Manuel utilisateur

ViewSonic

ViewSonic Pro8510L Manuel utilisateur

ViewSonic

ViewSonic PJ406D Manuel utilisateur

ViewSonic

ViewSonic PJ558D Manuel utilisateur

ViewSonic

ViewSonic Office Theater PJ860 Manuel utilisateur

ViewSonic

ViewSonic PJD6211 VS12618 Manuel utilisateur

ViewSonic

ViewSonic PJL802 Manuel utilisateur

ViewSonic

ViewSonic LiteBird PJ870 Manuel utilisateur

ViewSonic

ViewSonic PJD6543w Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur