View Benchmark 250 Manuel utilisateur
VIEW Micro-Metrology
Benchmark™ 250
Installation Manual
VIEW Micro-Metrology
Benchmark™ 250
Installation Manual
Copyright © 2012 VIEW Micro-Metrology, a Division of Quality Vision
International, Inc.
All rights reserved. Printed in the U.S.A.
Part No. 799030, Revision E, 03/12
Information in this document is subject to change without notice and
does not represent a commitment on the part of VIEW Micro-Metrology.
VIEW Mirco-Metrology, Benchmark, and the VIEW Mirco-Metrology
and Benchmark logos are trademarks of VIEW Micro-Metrology. All
other trademarks mentioned in this manual are property of their
respective owners.
Benchmark equipment is made in the U.S.A.
Installation Manual 799030, Revision E, 03/12 Page i
Table of Contents
Important System Labels iii
1 About This Manual 1
1.1 What This Chapter Contains 1
1.2 Who Should Read This Manual 1
1.3 Required Knowledge 1
1.4 What This Manual Contains 1
1.5 Where to Get Help 2
2 System Overview 3
2.1 What This Chapter Contains 3
2.2 What Is Benchmark 250? 3
2.3 System Components 4
2.4 How the System Operates 5
3 Safety Information 7
3.1 What This Chapter Contains 7
3.2 Emergency Stop 7
3.3 System Status LEDs 8
3.4 System Power 9
3.5 System Lockout 10
3.6 Safety Guidelines 11
4 Installation 13
4.1 What This Chapter Contains 13
4.2 Choosing an Installation Site 14
4.3 Unpacking the Machine 15
4.4 Removing the X, Y, and Z Restraints 19
4.5 Installing the Stage Glass 23
4.6 Arranging and Connecting the System 24
Installation Manual 799030, Revision E, 03/12 Page iii
Important System Labels
Label: Location: Definition:
Around the remote E-
Stop (Yellow ring
around red
switch)
Emergency stop
Left and right sides of
the stage, on the
substage
Do not lift
Front surface of the
electronics tower Pinch hazard
Top of rear door
Lower rear panel, above
power cord receptacle
Hazardous
voltagepresent;
disconnect
power before
servicing to
avoid electrical
shock
Lower-left corner of
Main System ID label System meets
the
requirements of
the European
Union (EU)
Page iv 799030, Revision E, 03/12 Benchmark 250
Front surface of the
electronics tower System model
and serial
number
Rear door, above lower
rear panel Main system ID
Front surface of the
electronics tower Exercise
caution near
this area
Right side of the laser
(if equipped) International
laser symbol
Right side of the laser
(if equipped) Indicates that
the laser meets
Class 2
requirements of
the IEC-825
European
standard
Label: Location: Definition:
Installation Manual 799030, Revision E, 03/12 Page v
Right side of the laser
(if equipped) Indicates that
the laser meets
Class II
requirements of
the CFR 21
standard
Right side of the laser
(if equipped) Identifies the
laser emitting
aperture
Label: Location: Definition:
Page vi 799030, Revision E, 03/12 Benchmark 250
This page has been left intentionally blank.
Autres manuels pour Benchmark 250
2
Table des matières
Autres manuels View Instrument de mesure
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur