Viessmann FDVS-4 Manuel utilisateur

Safety and Installation Requirements

Please ensure that these instructions are read and understood before commencing installation. Failure to comply with the

instructions listed below can cause product/property damage,severe personal injury, and/or loss of life.

Working on the equipment

The installation, adjustment, service,

and maintenance of this product must

be done by a licensed professional

heating contractor who is qualified and

experienced in the installation, service,

and maintenance of hot water boilers.

There are no user serviceable parts on

the boiler, burner, or control.

Ensure main power supply to

equipment, the heatin system, and all

external controls has been deactivated.

Close main oil supply valve. Take

precautions in both instances to avoid

accidental activation of power durin

service work.

Ensure that the installation

literature of other applicable

components is referenced.

General nformation

Standard installation

Boiler

Model

VR1 -22 -27 -33

Rear

Sides

Flue

inches

150

Floor Combustibles

Alcove installation

Boiler

Model

VR1 -22 -27 -33

Rear

Sides

Flue

Top*

inches

150

Floor Combustibles

* 24” with Vitotronic control.

The insulated oil direct vent system is

rated for a 1” clearance to

combustibles.

Advise owner to keep direct vent

termination and air intake free of

debris, snow and ice.

NOTE: Surface discoloration on the

outside of the buildin may occur if the

burner is not properly adjusted.

Viessmann will not accept any

responsibility for such discoloration.

NOTE: Direct Vent exhaust system

operates under a positive pressure

developed by the burner. Make sure all

vent connections and observation port

on the boiler are sealed air-ti ht by

ti htenin screws and usin hi h

temperature silicone sealant if

necessary.

NOTE: The vent components must be

supplied without any alteration except

for the len th of the flex pipe to be cut

to the desired len th.

Please file in Service Binder

5351 050 v2.5 09/2012

Installation Instructions

Supplement

for use by heating contractor

Direct Vent Systems,

Part No. Z005 875 (FDVS-4)

for Vitorond 100 boilers

MPORTANT

Viessmann will not assume any

responsibility for possible effects of

an obstructed air intake or exhaust

termination.

WARN NG

Installation

nstallation of nsulated Stainless Steel Flexible Oil Vent

In addition to the following

instructions, also consult

Field Controls Direct Vent

ystem manual for detailed

instructions on how to install

the venting system.

Use a 4” to 3” reducer (not supplied)

to connect an intake pipe to the Riello

burner.

If no air intake is required a=0 then

provide combustion air supply to

mechanical room where the burner is

installed. The burner requires fresh air

for safe operation and must be installed

in a mechanical room where there are

provisions for adequate combustion

and ventilation air.

Refer to Vitorond 100

Installation and ervice

Instructions.

Avoid dips in the ventin system when

usin the flexible insulated stainless

steel oil vent.

The direct vent kit includes a VRV-4

vacuum relief valve which must be

installed in the air intake pipe as close

as possible to the burner when usin a

Beckett burner (see Fi . 1).

*The direct vent kit includes a

Viessmann-specific stainless steel

boiler-to-vent transition adaptor.

Do not install the regular galvanized

vent pipe adaptor shipped with the

boiler. This galvanized vent pipe

adaptor is intended for chimney venting

application and therefore must be

discarded in a direct vent application.

5351 050 v2.5

*Boiler-to-vent

transition adaptor

(stainless steel)

Supports

Smoke test port

Exhaust

12” min. above

anticipated snow line

VRV-4

Vacuum

Relief

Valve

b=15’

a=20’

(max. 2 x 90°elbows)

Each 90° elbow = 3’ e.q.L.

=min. wall clearance 28”

(for min. bend radius of

flexible vent pipe)

Ø4”

max. 3’

Air intake

Fig. 1

MPORTANT

Burner - Beckett

Fig. 2

Burner Set-up (Beckett)

Electrical connections (with Aquastat control)

Installations must follow these codes

and requirements:

- National Electrical Code, ANSI/NFPA

70, latest edition and any addtional

national, state or local codes.

- In Canada, CSA C22.1 Canadian

Electrical Code Part 1 and any local

codes.

- Wirin must be N.E.C. Class 1. If

ori inal wire as supplied with boiler

must be replaced, type 105°C wire

or equivalent must be used. Supply

wirin to boiler and additional control

wirin must be 14 a. or heavier.

- Provide electrical round at boiler as

required by codes.

All field supplied nominal 120 VAC voltage wiring must be sheathed in a flexible metal conduit.

Disconnect means, overload protection and low water cut-off must be provided as required by local codes.

Connect incoming line voltage HOT (L1) wire to terminal L1, and N to terminal L2 of the Honeywell high limit control (see

wiring diagram on page 5.

Legend

Cable strap (supplied)

Honeywell hi h limit control

Burner wirin harness (supplied)

Burner wiring

The R7184 or GeniSys 7505P primary

control with valve-on delay (pre-purge)

and burner motor-off delay (post-purge

- factory default settings can be field

adjusted), requires a constant 120

VAC power source supplied to the

BLACK wire on the control (see wiring

diagram on following page).

1. The cover mountin plate is not a

conduit connection point. Pass

conduit and attached connector

throu h the front openin in the

mountin plate or throu h one of the

knockouts on either side of the cover

and attach it directly to the

burner-mounted 4x4 electrical

junction box.

Room thermostat wiring

1. Install thermostat on inside wall

away from influences of drafts, hot

or cold water pipes, li htin fixtures,

television, sun rays or fireplaces.

2. Follow instructions supplied with

room thermostat. If it has a heat

anticipator, set heat anticipator in

thermostat to match power

requirements of equipment

connected to it. Boiler wirin

dia rams ive settin for standard

equipment.

5351 050 v2.5

Electric shock hazard. Can cause

severe personal injury or loss of life if

power source, including service

switch on boiler, is not disconnected

before installing or servicing.

WARN NG

Ensure that burner wiring harness is

properly attached and secured to the

boiler side panel using the supplied

cable straps as depicted above. The

cable strap must be coiled on the

boiler side panel so that no slack is

left, allowing the burner/boiler door

to be swung open without

disconnecting the burner wiring

harness from the burner. Failure to

heed this warning may result in

personal injury.

WARN NG

MPORTANT

Burner - Beckett

Burner Set-up (Beckett)

(continued)

Electrical connections (with Aquastat control) (continued)

Installations must follow these codes

and requirements:

- National Electrical Code, ANSI/NFPA

70, latest edition and any addtional

national, state or local codes.

- In Canada, CSA C22.1 Canadian

Electrical Code Part 1 and any local

codes.

- Wirin must be N.E.C. Class 1. If

ori inal wire as supplied with boiler

must be replaced, type 105°C wire

or equivalent must be used. Supply

wirin to boiler and additional control

wirin must be 14 a. or heavier.

- Provide electrical round at boiler as

required by codes.

Burner wiring harness (supplied)

Fig. 3

5351 050 v2.5

Electric shock hazard. Can cause

severe personal injury or loss of life if

power source, including service

switch on boiler, is not disconnected

before installing or servicing.

WARN NG

white

black

red

15” *

1/4 quick

connect

insulated

fla

white

black

red

round

Burner - Beckett

Burner Set-up (Beckett)

(continued)

Wiring diagram (with Aquastat control) with outdoor reset module

Installations must follow these codes

and requirements:

- National Electrical Code, ANSI/NFPA

70, latest edition and any additional

national, state or local codes.

- In Canada, CSA C22.1 Canadian

Electrical Code Part 1 and any local

codes.

- Wirin must be N.E.C. Class 1. If

ori inal wire as supplied with boiler

must be replaced, type 105°C wire

or equivalent must be used. Supply

wirin to boiler and additional control

wirin must be 14 a. or heavier.

- Provide electrical round at boiler as

required by codes.

All field supplied nominal 120 VAC voltage wiring must be sheathed in a flexible metal conduit.

Disconnect means, overload protection and low water cut-off must be provided as required by local codes.

Connect incoming line voltage HOT (L1) wire to terminal L1, and N to terminal L2 of the Honeywell high limit control (see

wiring diagram below).

Fig. 4

Legend

Oil solenoid valve

I nition transformer

Burner motor

CAD cell flame detector

Burner roundin screw

R7184 Series primary control

with post-pur e (factory default

settin : 30 sec. - can be field

adjusted; see Beckett burner

manual)

Factory-installed jumper

5351 050 v2.5

Electric shock hazard. Can cause

severe personal injury or loss of life if

power source, including service

switch on boiler, is not disconnected

before installing or servicing.

WARN NG

Ensure that the burner cycles ON and

OFF on proper call for heat before

leaving the job site. Failure to do so

may lead to boiler runaway situation,

which may lead to property damage,

personal injury or death.

WARN NG

A field supplied manual reset high

limit control must be installed at the

outlet pipe of the boiler to interrupt

burner operation should the factory

supplied high limit control fail. This

field supplied high limit control must

be set 20°F above the setting of the

factory supplied high limit control.

The setting of this field supplied high

limit control must never be greater

than 220°F.

CAUT ON

Burner - Beckett

Burner Set-up (Beckett burner with GeniSys primary control)

(continued)

Wiring diagram (Vitorond 100 with Beckett (NX) burner and Honeywell Aquastat)

Installations must follow these codes

and requirements:

- National Electrical Code, ANSI/NFPA

70, latest edition and any additional

national, state or local codes.

- In Canada, CSA C22.1 Canadian

Electrical Code Part 1 and any local

codes.

- Wirin must be N.E.C. Class 1. If

ori inal wire as supplied with boiler

must be replaced, type 105°C wire

or equivalent must be used. Supply

wirin to boiler and additional control

wirin must be 14 a. or heavier.

- Provide electrical round at boiler as

required by codes.

All field supplied nominal 120 VAC voltage wiring must be sheathed in a flexible metal conduit.

Disconnect means, overload protection and low water cut-off must be provided as required by local codes.

Connect incoming line voltage HOT (L1) wire to terminal L1, and N to terminal L2 of the Honeywell high limit control (see

wiring diagram below).

Fig. 5

5351 050 v2.5

Electric shock hazard. Can cause

severe personal injury or loss of life

if power source, including service

switch on boiler, is not disconnected

before installing or servicing.

WARN NG

Ensure that the burner cycles ON and

OFF on proper call for heat before

leaving the job site. Failure to do so

may lead to boiler runaway situation,

which may lead to property damage,

personal injury or death.

WARN NG

A field supplied manual reset high

limit control must be installed at the

outlet pipe of the boiler to interrupt

burner operation should the factory

supplied high limit control fail. This

field supplied high limit control must

be set 20°F above the setting of the

factory supplied high limit control.

The setting of this field supplied high

limit control must never be greater

than 220°F.

CAUT ON

Burner - Beckett

Fig. 6

#41 plu -in connector

Burner Set-up (Beckett)

(continued)

Electrical connections (with Vitotronic control)

Installations must follow these codes

and requirements:

- National Electrical Code, ANSI/NFPA

70, latest edition and any addtional

national, state or local codes.

- In Canada, CSA C22.1 Canadian

Electrical Code Part 1 and any local

codes.

- Wirin must be N.E.C. Class 1. If

ori inal wire as supplied with boiler

must be replaced, type 105°C wire

or equivalent must be used. Supply

wirin to boiler and additional control

wirin must be 14 a. or heavier.

- Provide electrical round at boiler as

required by codes.

Burner wiring

The R7184 primary control with

valve-on delay (pre-purge) and burner

motor-off delay (post-purge - factory

default settings can be field

adjusted), requires a constant 120

VAC power source supplied to the

BLACK wire on the control (see

wiring diagram on page 9).

1. The cover mountin plate is not a

conduit connection point. Pass

conduit and attached connector

throu h the front openin in the

mountin plate or throu h one of the

knockouts on either side of the cover

and attach it directly to the

burner-mounted 4x4 electrical

junction box.

Electrical connections

1.Run the plu -in connector cable of

the Vitotronic control down behind

the front panel of the boiler and out

throu h the bottom. (Fi . 5)

2.Connect the female plu of the

burner to the male plu of the

Vitotronic control. (Fi . 5)

5351 050 v2.5

Electric shock hazard. Can cause

severe personal injury or loss of life if

power source, including service

switch on boiler, is not disconnected

before installing or servicing.

WARN NG

MPORTANT

Connections

Burner Set-up (Beckett)

(continued)

Electrical connections (with Vitotronic control) (continued)

Room thermostat wiring

1. Install thermostat on inside wall

away from influences of drafts, hot

or cold water pipes, li htin fixtures,

television, sun rays or fireplaces.

2. Follow instructions supplied with

room thermostat. If it has a heat

anticipator, set heat anticipator in

thermostat to match power

requirements of equipment

connected to it. Boiler wirin

dia rams ive settin for standard

equipment.

5351 050 v2.5

Connections

Burner Set-up (Beckett)

(continued)

Electrical connections (with Vitotronic control) (continued)

Burner wiring harness (supplied)

Fig. 7

Le end

BL Blue

O Oran e

BK Black

W White

G Green / Ground

R Red

*If Beckett burner is bein installed,

cut this len th to 6” for connection

to burner junction box (located

under the burner primary control).

Installations must follow these codes

and requirements:

- National Electrical Code, ANSI/NFPA

70, latest edition and any addtional

national, state or local codes.

- In Canada, CSA C22.1 Canadian

Electrical Code Part 1 and any local

codes.

- Wirin must be N.E.C. Class 1. If

ori inal wire as supplied with boiler

must be replaced, type 105°C wire

or equivalent must be used. Supply

wirin to boiler and additional control

wirin must be 14 a. or heavier.

- Provide electrical round at boiler as

required by codes.

5351 050 v2.5

Electric shock hazard. Can cause

severe personal injury or loss of life if

power source, including service

switch on boiler, is not disconnected

before installing or servicing.

WARN NG

Jumper

RED

Viessmann #41-plu

control connection

18” *

Blue

Closed end connectors are factory installed on

RED, ORANGE and BLUE wires. These RED,

ORANGE and BLUE wires may or may not be

used in your burner application. See wirin

dia ram in this manual which is specific to your

burner application. Do not remove or cut any of

the closed end connectors of the RED, ORANGE

or BLUE wires, unless it is necessary to do so.

RED wire is live (120VAC) at all times. Do not

remove or cut its closed end connector unless it

is necessary to do so. Failure to heed the above

instructions may cause severe personal injury or

loss of life.

Connections

Burner Set-up (Beckett)

(continued)

Wiring diagram (with Vitotronic control)

Installations must follow these codes

and requirements:

- National Electrical Code, ANSI/NFPA

70, latest edition and any additional

national, state or local codes.

- In Canada, CSA C22.1 Canadian

Electrical Code Part 1 and any local

codes.

- Wirin must be N.E.C. Class 1. If

ori inal wire as supplied with boiler

must be replaced, type 105°C wire

or equivalent must be used. Supply

wirin to boiler and additional control

wirin must be 14 a. or heavier.

- Provide electrical round at boiler as

required by codes.

Legend

Oil solenoid valve

I nition transformer

Burner motor

CAD cell flame detector

Burner roundin screw

R7184 Series primary control

with post-pur e (factory default

settin : 30 sec. - can be field

adjusted; see Beckett burner

manual)

Factory-installed jumper

5351 050 v2.5

Electric shock hazard. Can cause

severe personal injury or loss of life if

power source, including service

switch on boiler, is not disconnected

before installing or servicing.

WARN NG

Blue and oran e wires not used in this

application. DO NOT cut or remove closed

end connector from the wires.

120 VAC

power supply

installer must

provide 15A

overcurrent

protection

Main

ON/OFF

switch

(field supplied)

Low water

cut-off

(if required)

(field supplied)

Factory

installed

jumper

Burner junction box

120 VAC receptacle

(field supplied)

120 VAC

power

supply

to boiler

Power supply. Provide disconnect

means and overload protection as

required.

Control case must be connected

to earth round.

Refer to Vitotronic

200/300 (KW2/KW3)

for alternate connection

location of LWCO.

Fig. 8

Legend

Y Yellow

BL Blue

BK Black

O Oran e

W White

G Green / Ground

R Red

GY Gray

BR Brown

V Violet

Vitotronic Control

(Refer to correspondin Vitotronic Control manual)

Ensure that the burner cycles ON and

OFF on proper call for heat before

leaving the job site. Failure to do so

may lead to boiler runaway situation,

which may lead to property damage,

personal injury or death.

WARN NG

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Viessmann hotte de ventilation

Viessmann

Viessmann VITOVENT 300 Guide de démarrage rapide

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur