Viessmann VITOSOL-F Manuel utilisateur

Installation instructions

for contractors

VIESMANN

Vitosol-F/-FM

Type SVKA, SVKG

Flat-plate collector for pitched roofs, roof integration

VITOSOL-F/-FM

5698 362 GB 1/2016 Dispose after installation.

Please follow these safety instructions closely to

prevent accidents and material losses.

Safety instructions explained

!Please note

This symbol warns against the risk of material

losses and environmental pollution.

Note

Details identified by the word "Note" contain additional

information.

Target group

These instructions are exclusively intended for author-

ised contractors.

■Work on electrical equipment must only be carried

out by a qualified electrician.

Regulations to be observed

■National installation regulations

■Statutory regulations for the prevention of accidents

■Statutory regulations for the protection of the envi-

ronment

■Codes of practice of the relevant trade associations

■All relevant safety regulations as defined by DIN, EN,

DVGW, VDE and locally applicable standards

aÖNORM, EN and ÖVE

cSEV, SUVA, SVTI, SWKI and SVGW

Working on the system

■Isolate the system from the power supply (e.g. by

removing the separate fuse or by means of a mains

isolator) and check that it is no longer 'live'.

■Safeguard the system against reconnection.

Safety instructions

5698 362 GB

1. Information Disposal of packaging ............................................................................ 4

Symbols ................................................................................................. 4

Intended use .......................................................................................... 5

2. Installation sequence Components .......................................................................................... 6

Installation information ........................................................................... 6

Fitting the timbers .................................................................................. 7

Fitting the lower panels .......................................................................... 8

Installing the collectors .......................................................................... 9

■Making the hydraulic connections ...................................................... 11

Fitting the casing .................................................................................... 13

3. Covering the collector

array

................................................................................................................ 19

4. Installation ................................................................................................................ 20

5. Commissioning ................................................................................................................ 22

Index

5698 362 GB

Disposal of packaging

Please dispose of packaging waste in line with statu-

tory regulations.

DE: Use the disposal system organised by

Viessmann.

AT: Use the ARA statutory disposal system (Altstoff

Recycling Austria AG, licence number 5766).

CH: Packaging waste is disposed of by the HVAC

contractor.

Symbols

Symbol Meaning

Reference to other document containing

further information

Step in a diagram:

The numbers correspond to the order in

which the steps are carried out.

Warning of material losses and environ-

mental pollution

Live electrical area

Pay particular attention.

■Component must audibly click into place.

■Acoustic signal

■Fit new component.

■In conjunction with a tool: Clean the sur-

face.

Dispose of component correctly.

Dispose of component at a suitable collec-

tion point. Do not dispose of component in

domestic waste.

Disposal of packaging

5698 362 GB

The appliance is only intended to be installed and

operated in sealed unvented systems that comply with

EN 12828 / DIN 1988, or solar thermal systems that

comply with EN 12977, with due attention paid to the

associated installation, service and operating instruc-

tions. DHW cylinders are only designed to store and

heat water of potable water quality. Heating water buf-

fer cylinders are only designed to hold fill water of pot-

able water quality. Only operate solar collectors with

the heat transfer medium approved by the manufac-

turer.

Intended use presupposes that a fixed installation in

conjunction with permissible, system-specific compo-

nents has been carried out.

Commercial or industrial usage for a purpose other

than heating the building or DHW shall be deemed

inappropriate.

Any usage beyond this must be approved by the man-

ufacturer for the individual case.

Incorrect usage or operation of the appliance (e.g. the

appliance being opened by the system user) is prohibi-

ted and results in an exclusion of liability.

Incorrect usage also occurs if the components in the

system are modified from their intended use (e.g.

through direct DHW heating in the collector).

Adhere to statutory regulations, especially concerning

the hygiene of potable water.

Intended use

5698 362 GB

1qW

Fig. 1

1Timber

120 x 30 x 2500 mm

2Screws 8 x 120 mm

3Timber

48 x 30 x 2500 mm

4Nails

5Lower left panel with lead flashing

6Lower right panel with lead flashing

7Mounting plate with butyl strip

8Retaining bracket

9Fixing clamp with butyl strip

qP Fixing clamp

qQ Centre clamp

qW Left side panel

(for roof tiles and barrel roof tiles with sealing

strips)

qE Left cover strip

qR Centre panel

qT Right cover strip

qZ Right side panel

(for roof tiles and barrel roof tiles with sealing

strips)

qU Upper cover strip

qI Top panel

(for roof tiles and barrel roof tiles with sealing

strips)

qO Lower cover strip

Installation information

Required roof area: 2700 x 2700 mm

■To prevent any damage to the ridge cover, allow suf-

ficient clearance on the ridge side; at least 3 rows for

tiled roof cover.

Note

With tiled roof cover, we recommend also maintain-

ing a width of at least 3 tiles at the roof verges.

■If necessary, install a snow guard.

■Provide a roof hatch near the collectors for inspec-

tion and maintenance.

■Take additional measures on site to protect against

water penetration as a result of snow and wind pres-

sure, e.g. sarking membranes (accessories).

Components

5698 362 GB

Components

1Timber 120 x 30 x 2500 mm

2Screws 8 x 120 mm

3Timber

48 x 30 x 2500 mm

4Nails

160 720-840

1530-1650

2130

Fig. 2

■Provisionally position the lower timber parallel to the

lower row of tiles (tie a line as a guide).

■It may be necessary for existing battens to be

removed in the area taken up by the timbers.

Support the joint between batten and timber.

■If cantilevers are created, support them with an on-

site batten.

■Secure timbers along their entire length with 2

screws for every rafter.

Fitting the timbers

5698 362 GB

8x120 13

Fig. 3

Fitting the lower panels

Components

5Lower left panel with lead flashing

6Lower right panel with lead flashing

7Mounting plate with butyl strip

170

860

576x30

Fig. 4

Fitting the timbers (cont.)

5698 362 GB

170

860

6x30

Fig. 5

Installing the collectors

Components

9Fixing clamp with butyl strip

qP Fixing clamp

qQ Centre clamp

Fitting the lower panels (cont.)

5698 362 GB

105

6x30

Fig. 6

Note on step 9:

Do not tighten the screws yet. The second collector

must be pushed under the clamp.

!Please note

The connection pipes must not show any signs

of damage.

Lubricate O-rings only with the special valve

grease provided.

The collector temperature sensor is part of the stand-

ard delivery of the connection set.

Installing the collectors (cont.)

5698 362 GB

Autres manuels pour VITOSOL-F

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Viessmann Panneau solaire

Viessmann

Viessmann Vitovolt 200 Mode d'emploi

Viessmann

Viessmann Vitosol-F Series Manuel utilisateur

Viessmann

Viessmann VITOSOL 200-F Manuel utilisateur

Viessmann

Viessmann Vitosol 200-T Mode d'emploi

Viessmann

Viessmann Vitovolt 300 Manuel utilisateur

Viessmann

Viessmann VITOSOL 200-F Manuel utilisateur

Viessmann

Viessmann Vitosol 200-FM SV2F Mode d’emploi

Viessmann

Viessmann Vitosol 300-TM Manuel de service

Viessmann

Viessmann Vitosol 300-T Manuel utilisateur

Viessmann

Viessmann VITOVOLT series Mode d'emploi

Viessmann

Viessmann Vitosol 200-T Mode d'emploi

Viessmann

Viessmann VITOSOL-F Manuel utilisateur

Viessmann

Viessmann VITOSOL SERIES Guide de démarrage rapide

Viessmann

Viessmann VITOSOL-F Manuel utilisateur

Viessmann

Viessmann VITOSOL 100-F Mode d'emploi

Viessmann

Viessmann Vitosol100 Guide de démarrage rapide

Viessmann

Viessmann VITOSOL 200 Manuel utilisateur

Viessmann

Viessmann Vitosol 100 Manuel utilisateur

Viessmann

Viessmann Vitosol 222-T Manuel utilisateur

Viessmann

Viessmann VITOSOL-F Manuel utilisateur

Viessmann

Viessmann VITOSOL SERIES Manuel utilisateur

Viessmann

Viessmann Vitosol 222-T Mode d'emploi

Viessmann

Viessmann Vitosol 200-T Manuel utilisateur

Viessmann

Viessmann VITOSOL F Manuel utilisateur

Manuels Panneau solaire populaires d'autres marques

Navitron

Navitron HFC-2 Manuel utilisateur

AXITEC

AXITEC 60-CELL Manuel utilisateur

thermital

thermital TSOL 20 N BLU Manuel utilisateur

AZO Digital

AZO Digital MPPT-3000 Manuel utilisateur

Clenergy

Clenergy PV-ezRack SolarTripod Manuel utilisateur

Beretta

Beretta SCF-20N Manuel utilisateur

moovo

moovo KSM001 Manuel du produit

solarwatt

solarwatt EasyIn 60M Series Manuel utilisateur

Solarland

Solarland Portable Series Manuel

Ubiquiti

Ubiquiti sunMAX Manuel utilisateur

Lippert

Lippert Furrion FSFP37MW-BL Manuel utilisateur

Sonnenkraft

Sonnenkraft GK5-HP Manuel utilisateur

REC

REC TwinPeak 2S Mono 72 Series Manuel utilisateur

Sunforce

Sunforce 50039 Manuel utilisateur

Flexsolar

Flexsolar C100 Mode d’emploi

Süd Solar

Süd Solar 03005 Manuel utilisateur

Kodak

Kodak SP21 Manuel utilisateur

Carmanah

Carmanah Go Power! Solar Flex GP-FLEX-30 Manuel utilisateur