Videx DINB100-SA v2 Manuel utilisateur

USER’S MANUAL

v. c2

Standalone Biometric Reader

DINB100-SA v2

INTRODUCTION

MOUNTING

SPECIFICATIONS

APPLICATION DIAGRAM

RECOMMENDED SWIPING TECHNIQUE

INDICATION

WIRING

ADDING ADMIN FINGER

PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT

Pairing DINB100-SA with DINRTT

Pairing DINB100-SA with RTT

Pairing DINB100-SA with RU2

ADMINISTRATOR PROGRAMMING

ADD Finger Relay 1

ADD Finger Relay 2

ADD Finger Relay 1&2

DELETE Finger

DELETE ALL Fingers

CHANGE ADMIN Finger

CHANGE INSTALLER Finger

Administrator Programming block diagram

INSTALLER PROGRAMMING

Set Relay 1 Time

Set Relay 2 Time

BUZZER ON/OFF

BACKLIGHT ON/OFF

Installer Programming block diagram

ADMINISTRATOR PROGRAMMING BY KEYPAD

Contents

..............................................................

...........................................................

.............................................................

....................................................................

...........................................

..............................................................

..............................

...........................................................

..............................................................

...........................................................

...........................................

Do not install the device and cabling close to a source of strong electro-magnetic ﬁelds like radio-transmitting antenna.

Do not place the device near or above heating equipments.

If cleaning, do not spray or splash water or other cleaning liquids but wipe it out with smooth cloth or towel.

Do not let children touch the device without supervision.

Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and the ﬁngerprint can't be entered.

If the biometric reader is installed and used outdoor, the reader MUST be ﬁtted with the MC-MINI metal cover available in our accessories in order to protect

the sensor from direct rainfall. The operating temperature of the product is between -20ºC - + 50ºC. If the reader is installed in an environment where the

temperature can drop below -10ºC or/and if the sensor could only be exposed to direct sunlight, it is strongly recommended to install the reader inside a

third party sealed wall mount box (ﬁtted with additional heater if very low temperature) to keep a constant sensor level performance. Videx™ cannot

guarantee the functionality of the product if measures and advice before are not followed.

It is also strongly recommended to use double technology biometric readers when use outdoor to offer first higher security but also the possibility to use

different readers depending on users.

DINB100-SA v2 is access control ﬁngerprint reader designed for easy management of the users and conﬁguration. The

scanner is made with advanced capacitive sensing technology that provides some advantages over optical solutions like:

- making almost impossible to make fake copy of the users ﬁngers

- same performance in the diﬀerent light conditions

- good reading of ﬁngers with stains from daily jobs

Built in strong scanning and matching algorithm provides excellent tolerance in the way ﬁnger is swiped over the sensor

reducing to minimum the need to repeat ﬁnger swiping at the sensor.

The reader can store up to 100 ﬁnger templates. One template is reserved for User manager (Administrator), one

template is reserved for Reader conﬁguration (Installer) and up to 98 templates are for Users.

INTRODUCTION

Consult with installer about safety level of the installation. There are devices with relays compatible with this reader that can increase the security of

the system if needed. One or two enrolled ﬁngers are enough for one user. Ask the installer before he leaves the site to enroll your ﬁnger as

administrator.

Do not touch the sensor with other objects than ﬁnger. Do not pour or splash with water or other liquids. When painting or construction work is ongoing in

the area around the reader, protect the reader sensor area from possible damages and paint. If reader is to be dismounted or relocated, call authorized

installer for the job. Disposal of this product must be handled according to all national laws and regulations.

RECOMMENDATIONS

NOTES

The Reader is using physical roughness of the ﬁngerprint to scan the ﬁnger. Some of the users may have very ﬂat ﬁngertips, making diﬀicult for the sensor to

recognize correctly the ﬁngerprint. In most cases, these are children and older persons. To solve this problem, do the following:

1. Try with diﬀerent user’s ﬁngers to ﬁnd the “best” ﬁnger.

2. Check with the installer other models of the reader with added card reader or keypad for other type of access.

MAINTENANCE

No special or periodic maintenance is required. If cleaning is needed, use soft wet cloth and wipe gently the dirt. Do not use chemicals and materials that can

scratch the sensor.

WARNING!

MOUNTING

APPLICATION DIAGRAM

RS485 (max. 50m)

DINRTT (Oponal)

2 Relay Remote Unit

and request-to-exit Buon

DINB100-SA v2

Standalone Biometric Reader

RTT (Oponal)

1 Relay Remote Unit

and request-to-exit Buon

RU2 (Oponal)

2 Relay Remote Unit

DINB100-SA v2

SPECIFICATIONS

Follow the below instructions for correct finger swiping. Starting from the first finger joint, place the

selected finger on the swipe sensor and move it evenly towards oneself in one steady movement.

Result:

For a valid swipe: Tricolour Status LED turns green + OK Beep(short + long beep)

For an invalid or misread swipe: Tricolour Status LED turns red + Error Beep ( 3 short beeps)

Tricolor Status LED

- Access GrantedGreen

- Access deniedRed

- Idle ModeOrange

OK Beep - short + long beep

- 3 short beepsError Beep

Swipe Finger - 2 short beeps

RECOMMENDED SWIPING TECHNIQUE

INDICATION

Secured Area Outside

123

456

789

A0B

Oponal

Keypad

Oponal

Proximity Reader

use the cable provided

with the keypad/reader

Note: Frame sold separately

Fingerprint Capacity:

Output:

Push Button Input:

Door Open Time:

Entry Mode:

Programming:

Admin/Installer Fingers:

Backlight ON/OFF:

Buzzer ON/OFF:

Firmware upgrade:

Current Consumption:

Power Supply:

Indication:

IP Factor:

Storage/Operating Temperature :

Storage/Operating Humidity:

Dimensions(mm):

98 templates

1 x Relay ( )2 A /24V AC/DC

Yes

Pulse (1 to 30 seconds) or Toggle(ON/OFF)

Finger (basic installation)

Finger or Card (when used with card reader DIN Card reader)

Finger or PIN code (when used with keypad DINPAD-M)

By swiping

1 Administrator and 1 Installer Finger

Yes

via RS485 converter and windows application

100 mA max.

9-14 V DC

Tricolor Status LED

IP40

-20°C to +50°C

5% to 93% RH without condensation

80 x 80 x 9

ADDING ADMIN FINGER

1.Close the jumper on the back of the device.

2.Reset the Power of the device.

3.Wait for One long + mulple short beeps

4.Open the jumper. (short beeps will stop)

5.Wait for about 15 seconds for the LED to blink in Orange.

6.Swipe the Admin ﬁnger min.6 mes. (Unl Ok Beep)

Warning: This procedure also deletes all the users and the installer ﬁnger.

Warning: This procedure will unpair the connected relay unit (RTT, DINRTT or RU2)

WIRING

12/24V AC/DC

12V

GND

DINB100-SA

x 6

12V

GND

tamp

Relay Output

1N4007

Electric Door Strike

(DC powered)

Exit Buon (NO)

Jumper (Adding Master Finger)

12 VDC

12V

GND

tamp

GND(PB)

tamp

Alarm

12V

GND

Power Supply

(9-14V DC)

GND

+12V

GND

ARS485

Push Button

Tamper

tamp

Connection to additional

card reader or keypad

DINB100-SA v2

1. Close the Jumper. DINRTT beeps continuously and

the red led blinks.

2. Open the Jumper

3. Wait for Beep + OK Beep (short + short + long

beep)

After the OK beep, the coupling is done.

1. Put Dipswitch No.1 to position ON. RTT

beeps continuously and the red led

blinks.

2. Put Dipswitch No.1 to position OFF.

3. Wait for Beep + OK Beep (short + short +

long beep)

After the OK beep, the coupling is done.

If secure installation is needed, the reader can be connected to remote relay unit at secured area, which also can play the role of

request-to-exit push button. Follow the instructions bellow to pair(couple) both devices or refer to the Remote Relay’s Manual.

Warning: Changing the ADMIN ﬁnger will also unpair the remote relay unit.

PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT

Pairing DINB100-SA with DINRTT

Pairing DINB100-SA with RTT

Pairing DINB100-SA with RU2

1. Put the Jumper to closed position. RU2

beeps continuously and the red led

blinks.

2. Put the Jumper to open position.

3. Wait for Beep + OK Beep (short + short +

long beep)

After the OK beep, the coupling is done.

12 VDC

1N4007

RU2

Violet

Pink

COMNO

A (RS485)

B (RS485) +12V

GND

+12V

DINB100-SA v2

max. 50 meters

RS485

12V

GND

+12V

GND

12 VDC

DINB100-SA

+12V

GND

1N4007

12 VDC +

COM

RTT

1 2

PB2

GND

PB1

GND

NC1

COM

NO1

NC2

COM

NO2

BTAMP T AMP

RS485

GND

+12V

GND

+12V

Exit Button

(NO)

1N4007

RS485

12V

GND

+12V

GND

12 VDC

12 VDC +

DINB100-SA v2 DINRTT

+12V

GND

PB1

NO1

COM

1 2

max. 50 meters

short beep

Swipe Admin Finger 1 time

Action

Wait 5 seconds (until fast blinking)

Swipe User Finger min. 6 times

(until short + long beep)

Finger Backlight Buzzer Sound

x 1

Use point ﬁngers as Administrator and Installer. You can use the other ﬁngers as access ﬁngers.

Administrator ﬁnger is enrolled at the end of the system installation. Initial enrollment of the Admin

ﬁnger is described in installer manual.

ADMINISTRATOR PROGRAMMING

ADD Finger Relay 1 (Finger that will activate relay 1)

slow blinking

fast blinking short + long beep

short beep

INSTALLER

RIGHT

ADMIN

LEFT

x 6

Present card/tag 1 time fast blinking short + long beep

Swipe Admin Finger 2 times

Action

Wait 5 seconds (until fast blinking)

Finger Backlight Buzzer Sound

x 2

ADD Finger Relay 2 (Finger that will activate relay 2)

slow blinking

fast blinking

short beep

short + long beep

short beep

Swipe User Finger min. 6 times

(until short + long beep) x 6

Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.

Present card/tag 1 time fast blinking short + long beep

Swipe Admin Finger 3 times

Action

Wait 5 seconds (until fast blinking)

Finger Backlight Buzzer Sound

x 3

Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.

ADD Finger Relay 1&2 (Finger that will activate relay 1&2)

slow blinking

fast blinking

short beep

short + long beep

short beep

Swipe User Finger min. 6 times

(until short + long beep) x 6

Present card/tag 1 time fast blinking short + long beep

x 1

Swipe Admin Finger 4 times

Action

Wait 5 seconds (until fast blinking)

Swipe User Finger

Finger Backlight Buzzer Sound

x 4

DELETE Finger

slow blinking

fast blinking

short beep

short + long beep

short beep

x 1

Present card/tag 1 time short + long beep

fast blinking

Swipe Admin Finger 5 times

Action

Wait 5 seconds (until fast blinking)

Swipe NEW Admin Finger

min.6 times

Finger Backlight Buzzer Sound

x 5

x 6

short beep

short + long beep

3 short beeps

Swipe Admin Finger 6 times

Action

Wait 5 seconds (until fast blinking)

Swipe NEW Installer Finger

min.6 times

Finger Backlight Buzzer Sound

x 6

CHANGE ADMIN Finger

CHANGE/ADD INSTALLER Finger

slow blinking

fast blinking

short beep

short + long beep

short beep

slow blinking

fast blinking

short beep

multiple beeps

Swipe Admin Finger 4 times

Action

Wait 5 seconds (until fast blinking)

Swipe Admin Finger 2 times

Finger Backlight Buzzer Sound

x 4

x 2

DELETE ALL Fingers and Cards

slow blinking

fast blinking

short beep

x 1

CONNECTING DINB100 WITH DINMTPX PROXIMITY READER

DINMTPX

DINB100-SA v2

Connect both devices with the cable

provided. The proximity reader will be

powered via that cable. No extra power

supply for the proximity reader is needed.

Once connected, no further settings are

needed.

ADD Finger

Relay 1

1 swipe

ADD Finger

Relay 2

ADD Finger

Relay 1&2 DELETE FINGER

Change

ADMIN

Finger

Enroll

INSTALLER

Finger

2 swipes 3 swipes 4 swipes 5 swipes 6 swipes

Wait

5 seconds

(until fast blinking)

SWIPE

new finger

min. 6 times

present

card/tag

SWIPE

already enrolled

finger

1 time

present

card/tag

SWIPE

new finger

min. 6 times

present

card/tag

SWIPE

new finger

min. 6 times

present

card/tag

SWIPE

ADMIN finger

2 times

DELETE ALL

SWIPE

new ADMIN

FINGER

min. 6 times

SWIPE

new

INSTALLER

FINGER

min. 6 times

Swipe the ADMIN Finger 1 to 6 times depending of the desired menu

END END END END END END END

Administrator Programming block diagram

Only in combination

with DINRTT and RU2

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

Wait

5 seconds

(until fast blinking)

short beep

Swipe Installer Finger 1 time

Action

Swipe the INSTALLER Finger

and start counting seconds

Finger Backlight Buzzer Sound

Set Relay 1 Time

slow blinking

fast blinking beeps on 1 second

short beep

INSTALLER PROGRAMMING

x 1

Swipe the INSTALLER Finger

to stop or wait 30 seconds to

put the relay in toggle mode

fast blinking short + long beep

x 1

short beep

Swipe Installer Finger 2 times

Action

Swipe the INSTALLER Finger

and start counting seconds

Finger Backlight Buzzer Sound

Set Relay 2 Time

slow blinking

fast blinking beeps on 1 second

short beep

x 2

Swipe the INSTALLER Finger

to stop or wait 30 seconds to

put the relay in toggle mode

fast blinking short + long beep

x 1

Swipe Installer Finger 3 times

Action

Swipe Installer Finger

Finger Backlight Buzzer Sound

x 3

Swipe Installer Finger 4 times

Action

Swipe Installer Finger

Finger Backlight Buzzer Sound

x 4

BUZZER ON/OFF

slow blinking

fast blinking

short beep

short + long beep

short beep

slow blinking

fast blinking

short beep

short + long beep

short beep

BACKLIGHT ON/OFF

x 1

Wait 5 seconds (until fast blinking)

Relay 2 is available if the reader is used with remote relay unit with 2 relays(DINRTT and RU2). Consult the installer if Relay 2 is available in your system.

Table des matières