VIDAR NDT PRO Manuel utilisateur
VIDAR NDTPRO
Industrial Film Digitizer
Installation Guide
For Use with Windows 7 & Windows 8
(Serial Numbers 370,000 to 379,999)
P/N 19440-001, Rev C
19440-001 Rev. C VIDAR NDTPRO Industrial Film Digitizer Installation Guide 2
© Copyright 2017 by VIDAR® Systems Corporation. All rights reserved.
Terms denoted by the trademark symbol (or ®) used in this publication are trademarks
or service marks registered in the United States or other countries.
365 Herndon Parkway
Herndon, VA 20170 U.S.A.
Sales: 1-800-471-7226
Email: order@3dsystems.com
Phone: 1-703-471-7070
Fax: 1-703-471-7665
Internet: www.vidar.com
Technical Support:
Phone: 1-800-471-SCAN or 1-703-471-7070
E-mail: medtech@3dsystems.com
Emergo Europe
Prinsessegracht 20
2514 AP The Hague
The Netherlands
E-mail: europe@emergogroup.com
19440-001 Rev. C VIDAR NDTPRO Industrial Film Digitizer Installation Guide 3
Caution: No operator-serviceable parts inside. Refer servicing to qualified personnel.
Achtung: Gehäuse nicht öffnen. Wartung uno reparatur nur durch eletrofachkräfte.
Attention: Aucune piece ne peut etre remplacee par l’utilisateur. Toute operation de
maintenance doit etre effectuee par une personne qualiee.
Atencion: Acceso interno solo autorizado a personal tecnico cualificado.
Attenzione: Non appire. Rivolgersi a personale qualificado.
Radio Frequency Emissions
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in
a residential area can cause harmful interference, in which case the user will be required
to correct the interference at his or her own expense.
Product compliance testing was conducted using VIDAR shielded cables. Modifications
to the digitizer or the VIDAR shielded cables or the use of cables other than those
available from VIDAR could void the user’s authority to operate the equipment.
Acceptable shipping conditions
Temperature: –18° to +60°C (0° to +140°F)
Relative humidity: 20% to 85%, non-condensing
Atmospheric pressure: 500 to 106 hPa (+18,000 to –1,200ft)
Operating conditions
Temperature: 10°C to 30°C (60°F to 85°F)
Relative humidity: 20% to 85%, non-condensing
Atmospheric pressure: 696 to 1013hPa (10,000 to 0 ft)
Electrical supply
Voltage: 100 to 240 VAC
Current: 0.75 to 1.5 A
Frequency: 47 to 63 Hz
19440-001 Rev. C VIDAR NDTPRO Industrial Film Digitizer Installation Guide 4
Safety and compliance information
MEDICAL EQUIPMENT WITH RESPECT TO ELECTRIC SHOCK, FIRE AND
MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL60601-1,
IEC60601-1 AND CAN/CSA C22.2 No. 601.1
This product is intended to be turned on and left on. Operation is continuous. To maintain
Medical Equipment Certification, the digitizer must be connected to a host computer that
has been configured in accordance with IEC 60601-1-1.
This product is in the Ordinary Equipment Class. It provides no protection against the
ingress of water.
This product is not suitable for use in the presence of flammable anesthetic mixtures with
air or with oxygen or with nitrous oxide.
Class I Medical Device; No Applied Parts. This product provides Class I medical device
protection against electrical shock.
Power cords used with this device in North America must be rated by Underwriters
Laboratories for hospital use. Power cords used with this device in Europe must meet the
requirements of IEC 227 Designation 53 or IEC 245 Designation 53.
Correct and safe operation of the digitizer requires familiarity with
information that is not marked on the product. The following
symbol indicates the operator should consult the manual for
additional information.
This Class 1 LED device is safe under reasonably
foreseeable conditions of operation.
The LED illumination system consists of 16 Class 1
LEDs, a mirror system to spread the light, and a
diffuser to distribute the light approximately uniformly across an area of 2.4 sq in (15.5
sq cm). Light from the LED illuminator may be indirectly observed in the digitizer’s film
entry and exit areas.
5RA9
19440-001 Rev. C VIDAR NDTPRO Industrial Film Digitizer Installation Guide 5
Contents
VIDAR NDTPRO Industrial Film Digitizer Installation Guide................................................1
Intended Use......................................................................................................................6
Unpack................................................................................................................................7
1. Look for Damage......................................................................................................7
2. Unpack the shipping carton .....................................................................................8
3. Unpack the Accessory Box.......................................................................................9
4. Unwrap....................................................................................................................10
5. Identify the Components.........................................................................................11
6. If Anything Is Missing..............................................................................................12
7. Activate Your Product Warranty..............................................................................12
Setting Up.........................................................................................................................13
Identify Important Features.........................................................................................14
Assemble the Digitizer ................................................................................................15
Connect the Power Cord.............................................................................................20
VIDAR NDTPRO Industrial Film Digitizer Device Driver Installation Guide....................21
InstallDeviceDriversforWindows7&8....................................................................................22
1. Apply Power to the Digitizer....................................................................................22
About the VIDAR Drivers ............................................................................................23
2. Install the VIDAR Drivers ........................................................................................23
Appendix: Electromagnetic Guidance.................................................................................29
Appendix: Symbols...............................................................................................................33
19440-001 Rev. C VIDAR NDTPRO Industrial Film Digitizer Installation Guide 6
Intended Use
The NDTPRO Industrial Film Digitizer is intended for making digital copies of x-ray films for non-
destructive testing applications. This device is not intended for medical use.
19440-001 Rev. C VIDAR NDTPRO Industrial Film Digitizer Installation Guide 7
Unpack
In this chapter, you will:
Unpack and inspect the digitizer’s parts.
Identify the digitizer’s parts.
1. Look for Damage
Before unpacking the Digitizer, examine the shipping carton for damage.
If the carton is damaged:
Notify the shipper immediately.
Take photographs of the damage.
Send pictures and description of damage to: medtech@3dsystems.com.
Notify VIDAR Support at 1-703-471-7070.
19440-001 Rev. C VIDAR NDTPRO Industrial Film Digitizer Installation Guide 8
2. Unpack the shipping carton
IMPORTANT: Save all the packing materials. If you need to
ship the digitizer later, you should repack the digitizer in the
original materials by reversing the procedure described here.
Failure to properly pack, or failure to use VIDAR authorized
shipping materials, will void the product’s warranty, and will
likely result in costly repairs.
Remove items from the shipping carton in the order shown below.
1
Upper foam support
Feeder
Digitizer base
Accessory box
Shipping carton
Leave in box:
lower foam support
2
3
4
Note: For clarity, this
illustration does not show
the plastic bags surrounding
the digitizer and feeder.
19440-001 Rev. C VIDAR NDTPRO Industrial Film Digitizer Installation Guide 9
IMPORTANT: Save all the packing materials. If you need to
ship the digitizer later, you should repack the digitizer in the
original materials by reversing the procedure described here.
Failure to properly pack, or failure to use VIDAR authorized
shipping materials, will void the product’s warranty, and will
likely result in costly repairs.
3. Unpack the Accessory Box
a. Remove these items from the accessory box:
4
Documentation in
padded bag (bag
not shown)
Accessory box
USB cable
1
3
Power cord
Film support bar
in padded bag
(bag not shown)
2
19440-001 Rev. C VIDAR NDTPRO Industrial Film Digitizer Installation Guide 10
b. Then remove these items from the accessory box:
5
Cardboard retainer
Accessory box
7
Stand
6
Exit tray
4. Unwrap
a. Unwrap all items.
b. Remove the foam block from the rear of the digitizer base:
Note: For clarity, this
illustration does not show
the plastic bag surrounding
the exit tray.
Autres manuels pour NDT PRO
2
Table des matières
Autres manuels VIDAR Instrument de mesure
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur