Victron energy CCGX Manuel utilisateur

2020-11-11 18:45 1/2 CCGX: Upgrading to v2

Victron Energy - https://www.victronenergy.com/live/

CCGX: Upgrading to v2.00

Unlike previous updates, v2.00 can not be installed from the internet. Instead it needs a one time

manual upgrade. After this, future updates can be installed automatically from the internet again.

A microSD card is needed. It is not possible to use an USB stick.

The upgrade procedure:

Download venus-upgrade-image.card1.

Unzip it, and put its contents on a microSD card. The card needs to be formatted with either a2.

FAT or FAT32 ﬁle system.

Click ‘Safely remove hardware’ or another eject function on your computer.3.

Take the card out4.

Insert the card into the Ccgx5.

Press and hold (!) button E6.

Shortly press A and B at the same time (still hold button E!)7.

The screen will now brieﬂy switch oﬀ, then turn solid blue and show ‘prepare update’8.

Release button E9.

Next you’ll see the update progressing, all kinds of technical details ﬂying by.10.

After approximately 2 minutes, you’ll see “Remove SD/USB medium and reset system”11.

So, remove the card, and press buttons A and B again to reboot.12.

Upgrade complete already! But make sure to double check a few things:

All settings in the connected devices (Multis, BMV, Solar Charger etcetera) won’t be aﬀected.

Also all settings in the ccgx won’t be aﬀected. But still it is good to double check that.

Especially double check wiﬁ and/or ethernet passwords and IP conﬁguration.

For developers and people that customize the ccgx, make sure to read these developer notes on the

v2.00 upgrade.

Troubleshooting

Last update: 2016-12-14

12:43 ccgx:ﬁrmware_upgrade_to_v2 https://www.victronenergy.com/live/ccgx:ﬁrmware_upgrade_to_v2?rev=1481715791

https://www.victronenergy.com/live/ Printed on 2020-11-11 18:45

It restart normally and doesn't start the upgrade

Make sure to hold (!) button E till the upgrade starts

A blue screen is shown while booting and after ~1 minute, "Starting" is displayed

This means that the button pressing procedure was done OK, but that the CCGX did not ﬁnd an

update on the sd card. Common causes:

There is a problem with the formatting of the microSD card. Make sure it is formatted as FAT or1.

FAT32.

Not all ﬁles are on the microSD card. Make sure to unzip the zip ﬁle and put all contents on the2.

root folder on the card.

The sdcard is broken. (very rare, check item 1 and 2 ﬁrst)3.

The sdcard-slot on the CCGX is broken. (also very rare)4.

The screen stays solid blue (no Victron logo) and stays like that forever

Make sure button A is released after resetting. Pressing both A and E after a reset will interrupt the

boot. Try again, and release A before B.

"Update image not found. Error installing software"

This means that the button pressing procedure was done OK. And the sdcard is properly formatted.

Two possible causes

the .swu ﬁle is missing on the sdcard. Make sure to unzip all ﬁles on the sdcard1.

the sdcard slot in the CCGX is broken2.

DISQUS

View the discussion thread.

From:

https://www.victronenergy.com/live/ - Victron Energy

Permanent link:

https://www.victronenergy.com/live/ccgx:ﬁrmware_upgrade_to_v2?rev=1481715791

Last update: 2016-12-14 12:43

Autres manuels pour CCGX

9

Table des matières

Autres manuels Victron energy Contrôleurs

Victron energy

Victron energy MultiPlus-II 48/3000/35-32 230V GX Manuel utilisateur

Victron energy

Victron energy Cerbo GX Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/35 Manuel utilisateur

Victron energy

Victron energy SHS 200 MPPT Manuel utilisateur

Victron energy

Victron energy VBC 12-24-48V Manuel utilisateur

Victron energy

Victron energy BlueSolar Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/60 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 100/15 Manuel utilisateur

Victron energy

Victron energy Isolated SmartSolar MPPT RS 450/100 Manuel utilisateur

Victron energy

Victron energy SmartSolar MPPT 150/85 Series Manuel utilisateur

Victron energy

Victron energy BlueSolar PWM-Light 12/24-5 Manuel utilisateur

Victron energy

Victron energy VE.Bus BMS Manuel utilisateur

Victron energy

Victron energy SmartSolar MPPT 100/30 Manuel utilisateur

Victron energy

Victron energy CCGX Mode d'emploi

Victron energy

Victron energy CCGX Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/85 CAN-bus Manuel utilisateur

Victron energy

Victron energy BlueSolar 100/50A Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/45-MC4 Manuel utilisateur

Victron energy

Victron energy SmartSolar MPPT 100/30 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 75/10 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 75/10 Manuel utilisateur

Victron energy

Victron energy CCGX Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/60-Tr Manuel utilisateur

Victron energy

Victron energy SmartShunt IP65 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur