Victron energy BlueSolar Manuel utilisateur

Manual

Handleiding

Manuel

Anleitung

Manual

Appendix

BlueSolar PWM Charge Controller – LCD - USB

12V | 24V | 30A

48V | 10A

48V | 20A

48V | 30A

IMPORTANT

Always connect the batteries first.

Use for 12V battery system only 12V

(36 cells) solar panel array.

Use for 24V battery system only 24V

(72 cells) solar panel array.

Use for 48V battery system only 2x24V

(72 cells) solar panel array in series.

EN NL FR DE ES SV IT Appendix

1. General Information

The BlueSolar Charge Controller series uses Pulse Width Modulation (PWM) charge

voltage control combined with a multistage charge control algorithm.

2. Features

•Three stage battery charging [bulk – absorption – float]

•Battery type: Lead-ACID and LiFePO4 (with internal BMS)

•Protected against over current.

•Protected against short circuit.

•Protected against reverse polarity connection of the solar panels and/or battery.

•Low voltage load disconnect.

•Temperature protection.

3. Installation

Important note: Always connect the batteries first.

IMPORTANT

Always connect the batteries first.

•Use for 12V battery system only 12V (36 cells) solar panel array.

•Use for 24V battery system only 24V (72 cells) solar panel array.

•Use for 48V battery system only 2x24V (72 cells) solar panel

array in series.

1. Connect the battery to the charge regulator - plus and minus.

2. Connect the solar module to the regulator - plus and minus.

3. Connect the load to the charge regulator - plus and minus.

The reverse order applies when deinstalling!

An improper sequence order can damage the BlueSolar Charge Controller!

1. Make sure your battery is charged for the BlueSolar Charge Controller to

recognize the battery type before first installation.

2. The battery cable should be as short as possible to minimize losses.

3. The BlueSolar Charge Controller is only suitable for lead-acid, and LiFePO4

batteries.

4. The BlueSolar Charge Controller is only suitable for regulating solar modules.

Never connect another charging source to the charge BlueSolar Charge

Controller.

EN NL FR DE ES SV IT Appendix

4. LCD DISPLAY and SETTINGS

MENU：switch between different display, or to enter/exit setting by long press.

UP：press to change the settings when in setting mode.

DOWN: press to change the settings when in setting mode.

Load on/off button when in H mode.

4.1 Monitoring & Settings

Values between [ ] are for 24V battery settings. Bolt are the 48V settings.

Boot Display. After connecting the batteries, you see the type

of charger and the measured battery voltage.

1230= BlueSolar Charge Controller – LCD – USB 12V|30A

2430= BlueSolar Charge Controller – LCD – USB 24V|30A

4810= BlueSolar Charge Controller – LCD – USB 48V|10A

4820= BlueSolar Charge Controller – LCD – USB 48V|20A

4830= BlueSolar Charge Controller – LCD – USB 48V|30A

Press MENU to enter next display.

Main display. It shows battery voltage, battery capacity,

charging and discharging status.

Press MENU to enter next display.

Change Settings Main

display.press on the

MENU key for

several seconds until

the numbers flash, you

are in:

Battery type setting.

See table below.

The factory setting is b01

*The controllers do not have a remote on/off input. Therefore use LiFePO4 batteries with integrated BMS

only (such as the Victron SuperPack batteries)

NA for 48V

press on the MENU

key again and you are

in:

Low voltage disconnect

The factory setting is 11.2V

[22.4V] 44.8V

press on the MENU

key again and you are

in:

Low voltage reconnect

The factory setting is 12.6V

[25.2V] 50.4V

Solar Voltage display. It shows Solar Panel voltage,

battery capacity status.

Press MENU to enter next display.

Battery type

Battery

voltage

Absorbti

voltage

Float

voltage

Low voltage

disconnect

factory

setting

Low voltage

disconnect

range

Low voltage

reconnect

factory setting

Low voltage

reconnect range

b01

LEAD-ACID

[AGM]

12.0V [24V]

48V

14.4V

[28.8V]

57.6V

13.7V

[27.4V]

54.8V

11.2V [22.4V]

44.8V

10.5V-12.0V

in steps of

0.1V

12.6V [25.2V]

50.4V

12.0V-13.5V in

steps of 0.1V

b02

LEAD-ACID

[Gel]

12.0V [24V]

48V

14.2V

[28.4V]

56.8V

13.7V

[27.4V]

54.8V

11.2V [22.4V]

44.8V

10.5V-12.0V

in steps of

0.1V

12.6V [25.2V]

50.4V

12.0V-13.5V in

steps of 0.1V

b03

LEAD-ACID

[Wet]

12.0V [24V]

48V

14.6V

[29.2V]

58.4V

13.7V

[27.4V]

54.8V

11.2V [22.4V]

44.8V

10.5V-12.0V

in steps of

0.1V

12.6V [25.2V]

50.4V

12.0V-13.5V in

steps of 0.1V

b04*

12V

LiFePO4

12.8V

14.2V

13.35V

11.2V

10.5V-12.0V

in steps of

0.1V

12.6V

12.0V-13.5V in

steps of 0.1V

b05*

24V

LiFePO4

25.6V

28.4V

26.7V

22.4V

21.0V-24.0V

in steps of

0.1V

25.2V

24.0V-27.0V in

steps of 0.1V

EN NL FR DE ES SV IT Appendix

Charge current display. It shows solar to battery current

and charge status.

Press MENU to enter next display.

Load working mode.

The factory setting is 24H

Press MENU to enter next display.

Change Settings in the

Load working mode

display.

Press on the MENU

key for several seconds

until the numbers flash,

you are in setting mode

for the:

Load working mode setting.

See table below.

Press on the MENU

key again and you go

to:

(Note: the Phoenix

VE.Direct inverters can

be controlled by

connecting to the left

side connection of the

remote control to the

load output)

Load Setting: trigger value

(Solar Panel Voltage)

When the work mode is L01-

L23 the charge Controller will

measure the solar panel

voltage to decide whether its

day or night to switch load on

or off. The higher this value is

the earlier it switches on the

load output.

The factory setting is 4/8V/16V

Press on the MENU

key again and you go

to:

L01-L23 trigger delay value

(Seconds)

When the charge Controller

measures a solar panel voltage

lower this value it will delay for

The load can switch on and off by the Load on/off switch

Load D2D. The load will switch on at sunset and switch off at sunrise.

L01-L23

The load output will switch on after sunset and switch off after 1-23

hours.

24H

The BlueSolar Charge Controller will continuously supply power to

your load.

10s and measure again to

make sure night falls. The

factory setting is 10sec

Press on the MENU

key again and you go

to:

Short-circuit protection

setting.

Some inductive or capacitive

consumer will trigger the short-

circuit protection during start

up. Therefore the SC-

protection can be disabled

manually. Sc.F=OFF,

Sc.n=ON. The default is ON.

The factory setting is Sc.n.

Load current display. It shows load current and battery

capacity.

Press MENU to enter next display.

USB Voltage display. It shows the USB voltage

5V (2A max)

Press MENU to enter next display.

Controller temperature display. If the controller

overheats it will automatic shut down and wait for the

temperature to drop to normal level and then it will start

again.

Press Press MENU to enter Main display.

Table des matières

Langues :

Autres manuels Victron energy Contrôleurs

Victron energy

Victron energy Lynx Smart BMS Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/70 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 75/10 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/70 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 75/10 Manuel utilisateur

Victron energy

Victron energy CCGX Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/35 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/70-Tr Manuel utilisateur

Victron energy

Victron energy Isolated SmartSolar MPPT RS 450/100 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 75/10 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 75/10 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/85 Manuel utilisateur

Victron energy

Victron energy VBC 12-24-48V Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/35 Manuel utilisateur

Victron energy

Victron energy Color Control GX Guide d'installation

Victron energy

Victron energy BlueSolar MPPT 150/60-Tr Manuel utilisateur

Victron energy

Victron energy Digital Multi Control 200/200A Manuel utilisateur

Victron energy

Victron energy Isolated SmartSolar MPPT RS 450/100 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/45-MC4 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 150/35 Manuel utilisateur

Victron energy

Victron energy MPPT Control Manuel utilisateur

Victron energy

Victron energy BlueSolar PWM-Light 12/24-5 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 75/15 Manuel utilisateur

Victron energy

Victron energy BlueSolar MPPT 70/15 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur