Viavi T-BERD/MTS-580 Guide d'installation

VIAVI//Public

T-BERD/MTS-5800 Handheld Network Tester

T-BERD/MTS-5800 Network Tester

QUICK CARD

► Use the VIAVI P5000i or FiberChek Probe

microscope to inspect both sides of every

connection being used (OCC Port, Launch

Cable, bulkhead connectors, patch cables, etc.)

► Focus fiber on the screen. If dirty, clean the

end-face.

► If it appears clean, run inspection test.

► If it fails, clean the fiber and re-run inspection

test. Repeat until it passes.

Figure 2: Inspect Before You Connect

Figure 1: Equipment Requirements

CWDM Optical Channel Checker

This quick card describes how to connect to a fiber under test, configure CWDM Optical

Channel Checker (OCC) test setups, run tests, and analyze results with a T-BERD/MTS-

5800 equipped with a COSA-4055 module.

Note: The COSA module is used to monitor wavelengths on a live network.

Care should be exercised when unplugging fibers from the network as the

fibers may be carrying traffic.

► T-BERD/MTS-5800 equipped with the

following:

► Fiber Optics Software Release V21.0 or

greater

► COSA-4055 CWDM OCC Module

► Fiber optic cleaning and inspection tools

►20-meter Fiber optic patch cable (Launch

Cable)

► Optical Coupler to connect Launch Cable to

Fiber Under Test

VIAVI//Public

T-BERD/MTS-5800 Handheld Network Tester

T-BERD/MTS-5800 Network Tester

QUICK CARD

CONNECT TO FIBER UNDER TEST (FUT)

All fibers and connectors should be cleaned and inspected prior to connection, as described on page 1.

The OCC is typically connected to the FUT via a Monitor Port or splitter/tap to not disrupt service. The

OCC can also be directly connected to the common port or common fiber via a coupler during turn up or

maintenance:

Figure 3: Connecting to Monitor Port

Figure 4: Connecting to Common Cable

1. Inspect the OCC port on top of the test set.

2. If connecting to the Common Cable, connect the Common Cable to an optical coupler with the same

connector type and inspect the fiber end face in the coupler.

3. If connecting to the Monitor Port or Common Port on the Mux, inspect the Mux Port.

4. Inspect the fiber end face of the Launch Cable.

5. Connect the Launch Cable to the OCC port.

6. Inspect the other fiber end face of the Launch Cable.

7. Connect the Launch Cable to the coupler or Mux port.

VIAVI//Public

T-BERD/MTS-5800 Handheld Network Tester

T-BERD/MTS-5800 Network Tester

QUICK CARD

1. If files are to be saved, tap the File soft key

and tap the fiber folder .

Otherwise proceed to step 4.

2. Tap the Create Directory soft key,

enter a name for your new folder and tap the

Enter key. All trace files will be saved to this

directory.

3. Tap the Exit soft key .

4. Tap the Setup soft key to display the Setup

menu.

5. Tap Auto-set to auto-configure the OCC for a

single sweep.

6. Tap the Analysis tab. If a splitter/tap is used to

access the signal, set Splitter Value to the

splitter loss (in dB or %).

LAUNCH TEST

1. Press the Power button

to start the test instrument.

2. Tap the Fiber Optics icon

in the Status Bar at the top of the screen.

3. If a purple symbol is displayed on the left

screen side, tap it to display the Fiber Optics

home screen.

4. Tap the COSA icon until it is yellow and

highlighted.

Figure 5: Fiber Optics Home Screen

Figure 7: Setup Menu

CONFI G U RE T E ST

Figure 6: File Menu

VIAVI//Public

T-BERD/MTS-5800 Handheld Network Tester

T-BERD/MTS-5800 Network Tester

QUICK CARD

Product specifications and descriptions in this

document are subject to change without notice.

Patented as described at viavisolutions.com/patents

To reach the VIAVI office nearest you,

visit viavisolutions.com/contact

+1 844 GO VIAVI

(+1 844 468-4284)

RUN TES T

1. Tap the START soft key to start the test.

2. The OCC will sweep the entire CWDM

wavelength range. Results will be shown in

graphical and tabular formats as shown in

Figure 8: Test Results.

3. Verify that traffic is on all expected channels, at

the anticipated wavelengths and power levels,

and that there are no unexpected wavelengths

present.

4. Things to look for:

►Every expected wavelength/channel is

present.

►Channels are about 20 nm apart.

►Power levels of each channel are within

roughly 3 dB of each other, or within the

relative amplitude specification of the

Network Equipment Manufacturer.

Figure 8: Test Results

FAST REP O RT

1. Tap the Fast Report soft key .

2. Enter Cable ID, Fiber Number, Locations, and

Direction.

3. Tap Save .

4. Tap to accept the default filename and save

test results.

5. Tap the Fast Report soft key again to return to

the results display.

6. Tap to return to the OTDR Home screen.

Figure 9: Fast Report

Ce manuel convient aux modèles suivants

Autres manuels Viavi Équipement de test

Viavi

Viavi T-BERD/MTS-2000 Manuel de la liste des pièces

Viavi

Viavi HST-3000 Manuel utilisateur

Viavi

Viavi 3900 Series Manuel du propriétaire

Viavi

Viavi OneAdvisor-1000 Manuel utilisateur

Viavi

Viavi HST-3000 Manuel de la liste des pièces

Viavi

Viavi ATC-5000NG Manuel utilisateur

Viavi

Viavi ComXpert CX100 Manuel utilisateur

Viavi

Viavi Xgig Maestro Manuel de référence

Viavi

Viavi OneAdvisor 1000 Manuel utilisateur

Viavi

Viavi T-BERD 5800 Manuel de la liste des pièces

Viavi

Viavi OTU-8000 Manuel de la liste des pièces

Viavi

Viavi T-BERD 5800 Manuel utilisateur

Viavi

Viavi T-BERD/MTS 4000 Manuel utilisateur

Viavi

Viavi OCC-4056 Manuel de la liste des pièces

Viavi

Viavi T-BERD 6000A V2 Manuel de la liste des pièces

Viavi

Viavi T-BERD MTS 5800 Manuel de la liste des pièces

Viavi

Viavi OneExpert DSL ONX-580 Manuel utilisateur

Viavi

Viavi 3900 Series Manuel utilisateur

Viavi

Viavi Seeker X with MCA III Manuel utilisateur

Viavi

Viavi MTS 2000 Manuel utilisateur

Viavi

Viavi HST-3000 Manuel de la liste des pièces

Viavi

Viavi OSA-4100 Manuel utilisateur

Viavi

Viavi OLP-88 Manuel utilisateur

Viavi

Viavi ALT-9000 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur