Viavi OneAdvisor-1000 Manuel utilisateur

VIAVI//Public

OneAdvisor-1000 Portable Network Tester

QUICK CARD

►Use the VIAVI P5000i or FiberChek Probe

microscope to inspect both sides of every

connection being used (OCC Port, Launch

Cable, bulkhead connectors, patch cables, etc.)

►Focus fiber on the screen. If dirty, clean the

end-face.

►If it appears clean, run inspection test.

►If it fails, clean the fiber and re-run inspection

test. Repeat until it passes.

Figure 2: Inspect Before You Connect

Figure 1: Equipment Requirements

4100-series Expert OTDR

This quick card explains how to connect to a fiber under test, configure EXPERT OTDR

test settings using Quick Setup, run tests, and analyze results on a VIAVI

ONA-1000 equipped with a 4100-series OTDR module.

► ONA-1000 equipped with the following:

•Fiber Optics Software Release V21.12 or

greater

•4100 Series OTDR Module

•Fiber optic cleaning and inspection tools

►20-meter Fiber optic patch cable (Launch

Cable)

► Optical Coupler to connect Launch Cable to

Fiber Under Test

VIAVI//Public

OneAdvisor-1000 Portable Network Tester

QUICK CARD

CONNECT TO FIBER UNDER TEST (FUT)

All fibers and connectors should be inspected and

clean prior to connection, as described on page 1.

The OTDR may be connected to the FUT via an

optical patch panel (OPP) or a coupler:

1. Inspect the OTDR port on top of the test set.

2. Inspect the fiber end face of the Launch Cable.

3. Connect the Launch Cable to the OTDR port.

4. If the interface to the FUT is a patch cord,

connect the patch cord to an optical coupler.

5. Inspect the FUT connected to the coupler or

OPP port and the fiber end face of the Launch

Cable.

6. Connect the Launch Cable to the coupler or

OPP port.

Figure 5: Connecting to OPP

LAUNCH TEST

1. Press the Power button on the top of the

OneAdvisor to start the test instrument.

2. Tap the Tests icon

3. Select the OTDR Module

4. Tap the OTDR EXPERT icon

Figure 6: Fiber Optics Home Screen

Figure 4: Connecting to coupler

Figure 3: OTDR Port Inspection

VIAVI//Public

OneAdvisor-1000 Portable Network Tester

QUICK CARD

CONFIGURE TEST

Figure 7: Setup, Display

1. Tap the Setup soft key .

2. Tap Display and set Distance Unit to your

desired unit of measure.

3. Tap Acquisition and configure the following

basic settings for the trace:

►Laser: Select the wavelength(s) to test.

–Select All or select 1310 nm and

1550 nm to enable bend detection.

►Acquisition Mode:

–Select Manual to manually to enter

Range and Pulse width settings.

–Select Auto to automatically configure

Range, Pulse width, and Resolution

settings.

–Select SmartAcq to perform an

acquisition with a short pulse width,

followed by an acquisition with a longer

pulse width. The first acquisition allows

events at the beginning of the fiber to

be detected more precisely.

►Acq. Time: Select Realtime,Auto or the

desired time to sample the fiber.

►Launch Cable: Select and enter Length

if you are using a Launch Cable.

Enter 20 meters or 66 feet for Viavi

supplied 20-meter launch cables.

4. Tap Alarms and configure pass/fail criteria:

►Set Alarm Level to Fail.

►Set Threshold to Default, or select

alternate alarm thresholds (TIA-568.3,

User, etc.)

Figure 8: Setup, Acquisition

Figure 9: Setup, Alarms

VIAVI//Public

OneAdvisor-1000 Portable Network Tester

QUICK CARD

Figure 11: SmartLink View, Summary Results

RUN TEST

1. Press the Start soft key to start the test.

After auto-configuration, the OTDR will perform

a connection check to ensure that the

connection is Good. If the Connection is Bad,

disconnect the launch cable, and reconnect as

described on pages 1 and 2, cleaning every fiber

that fails the inspection test.

2. The OTDR will perform an acquisition at the

configured wavelength.

Figure 12: SmartLink View, Event Results

Figure 10: Connection Check

1. Tap the SmartLink tab at the left screen top to

select SmartLink view.

2. Set the toggle switch at the right screen top to

Event Line.

3. View SmartLink results:

►The FUT is displayed as a series of icons

representing events (front connector,

launch cable, connectors, splices, bends,

etc.) and distances. Swipe left or right to

view additional icons on spans with more

than 4 events.

►The center of the display shows summary

results for the entire span for each

acquisition or wavelength. Tap any event

in the upper display to view detailed results

for that specific event.

►Events are marked with a green check or

red xbased on the Alarms setting.

Note: the icon-based view may not be

available on older ONA-1000s when

acquisition Mode = SmartAcq. Rerun the test

with Mode = Auto or contact VIAVI to upgrade

your unit to add this feature.

VIEW SMARTLINK MAP

VIAVI//Public

OneAdvisor-1000 Portable Network Tester

QUICK CARD

VIEW TRACE

1. Tap the Trace tab at the left screen top to select

Trace view.

2. Set the toggle switch at the screen top to Info.

3. Tap to auto-zoom.

4. View trace results:

►Trace information is shown in the upper

display.

►Graphical results (dB versus distance) are

shown in the center display.

►A color-coded Event table is shown in the

lower display. Swipe up and down to view

all events. Figure 13: Trace view

Figure 14: Table view

1. Tap the Table tab at the left screen top to

select Table view.

2. Set the toggle switch at the right screen top to

the center (off) position.

3. View table results:

►Distance, Loss, and Reflectance are

shown for each event.

►Tap the toggle switch to view All events or

Failed events.

VIEW TABLE

VIAVI//Public

OneAdvisor-1000 Portable Network Tester

QUICK CARD

Product specifications and descriptions in this

document are subject to change without notice.

Patented as described at viavisolutions.com/patents

To reach the VIAVI office nearest you,

visit viavisolutions.com/contact

+1 844 GO VIAVI

(+1 844 468-4284)

FAST REPORT

1. Tap the File soft key and tap the Project

folder.

2. Tap the Create Directory soft key and

enter a name for your new folder. All trace files

will be saved to this directory.

3. Tap the Exit soft key .

4. Tap the Fast Report soft key and enter

Cable ID, Fiber Number, Locations,

Direction, and Save Mode.

5. Tap Save.

6. Tap to accept the default filename and

save test results.

7. Tap the Fast Report soft key again to return to

the results display.

Figure 15: File Explorer

Figure 16: Fast Report

Autres manuels Viavi Équipement de test

Viavi

Viavi 8000 V2 Platform Manuel de la liste des pièces

Viavi

Viavi OneExpert DSL ONX-580 Manuel utilisateur

Viavi

Viavi T-BIRD-4000 Manuel de la liste des pièces

Viavi

Viavi SmartClass Fiber OLS-85 Manuel utilisateur

Viavi

Viavi 8800SX Manuel utilisateur

Viavi

Viavi OneAdvisor ONA-800 Manuel technique

Viavi

Viavi T-BERD/MTS 5800 Manuel utilisateur

Viavi

Viavi SmartOTDR Manuel de la liste des pièces

Viavi

Viavi OneAdvisor ONA-800 Manuel de la liste des pièces

Viavi

Viavi OneAdvisor 1000 Manuel utilisateur

Viavi

Viavi SmartClass Fiber OLTS-85 Manuel utilisateur

Viavi

Viavi T-BERD/MTS 5800 Manuel utilisateur

Viavi

Viavi Certifier Series Manuel utilisateur

Viavi

Viavi T-BERD MTS 5800-100G Manuel de la liste des pièces

Viavi

Viavi ComXpert CX100 Manuel utilisateur

Viavi

Viavi T-BERD/MTS-5800 OCC-4056C Manuel de la liste des pièces

Viavi

Viavi OneExpert ONX CATV Manuel utilisateur

Viavi

Viavi HST-3000 Manuel de la liste des pièces

Viavi

Viavi P5000i Manuel utilisateur

Viavi

Viavi NSC-100 Manuel utilisateur

Viavi

Viavi ALT-9000 Manuel de la liste des pièces

Viavi

Viavi T-BERD/MTS 2000 Manuel utilisateur

Viavi

Viavi T-BERD 5800 Manuel de la liste des pièces

Viavi

Viavi SmartClass Fiber MPOLx Manuel de la liste des pièces

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur