Viavi T-BERD 5800 Manuel utilisateur

Page 1 of 14

Technical Support [email protected] 1-844-468-4284

Viavi T-BERD 5800

RFC-2544 Layer 3 IPv4

Testing Guide

Version 25.x

January 15, 2017

TableofContents

Scope................................................................................................................................................................ 2



Hardware Description............................................................................................................................... 3



T-BERD 5800 Remote Unit setup............................................................................................................ 4



2.1



Information requirements.................................................................................................................. 4



2.2



Test Setup.......................................................................................................................................... 4



T-BERD 5800 RFC-2544 Test Procedure................................................................................................ 8



3.1



Information requirements.................................................................................................................. 8



3.2



Test Setup.......................................................................................................................................... 8



3.3



Configuring RFC-2544 Test Settings ............................................................................................. 10



3.4



Running the Test............................................................................................................................. 12



3.5



Saving Test Results......................................................................................................................... 14



Page 2 of 14

Technical Support [email protected] 1-844-468-4284

Scope

This document describes how to measure Metro Ethernet performance with the T-BERD 5800v2 or T-

BERD 5800-100G in accordance with Viavi’s Enhanced RFC 2544 test methodology. RFC-2544 is a

recommended test suite for verifying key performance indicators (KPIs) including Throughput, Delay and

Frame Loss. Viavi’s Enhanced RFC 2544 Test Suite also measures Jitter and Committed Burst Size (CBS)

to verify conformance to a Service Level Agreement (SLA) or Service Level Objectives. This document is

not intended to be a user guide. This Method of Procedure (MOP) should be used in conjunction with the

T-BERD User’s Guides for detailed explanation of all testing options.

The following procedures are documented:

Setting up the T-BERD up as a Layer 3 IPv4 Loopback device (Section 2)

Running a Layer 3 IPv4 RFC-2544 tests from the T-BERD (Section 3)

The Loopback device may be another Viavi test set (SmartClass, HST-3000 or T-BERD), a Viavi Test

Head (QT-600), a Viavi-compatible NID, or a Viavi JMEP loopable SFP.

Figure 1: T-BERD to Viavi compatible loopback device

The following minimum software revision is recommended:

T-BERD 5800-100G BERT Software Release 25.0

T-BERD 5800v2 BERT Software Release 25.1

If your T-BERD is Strata Sync enabled, use StrataSync to update your software. Otherwise, go to

http://updatemyunit.net/ for software update instructions. StrataSync can also be used to create

configuration templates and download configuration files for this procedure.

Page 3 of 14

Technical Support [email protected] 1-844-468-4284

1. Hardware Description

The T-BERD 5800 is a portable test tool for Ethernet testing. The product can also be optioned to support

T1, DS3, SONET, OTN, Fiber Channel, CPRI, and OBSAI. Test connections are made from the top of the

mainframe. Menu selections are made from the T-BERD’s color touch screen. . The T-BERD 5800v2

uses RJ-45 ports, labeled 10/100/1000 for copper testing (10/100/1000BASE-T) and SFP+ ports for optical

testing:

Figure 2: T-BERD 5800v2 Top View (dual port configuration)

The T-BERD 5800-100G uses the SFP+ port for both copper and optical testing. The RJ-45 10/100/1000

port is only used for dual port testing and requires option C5DUALPORT:

Figure 3: T-BERD 5800-100G Top View

Page 4 of 14

Technical Support [email protected] 1-844-468-4284

2. T-BERD 5800 Remote Unit setup

Follow this procedure to set up a T-BERD as a layer 3 IPv4 loopback device.

2.1 Information requirements

The following information is required to set the T-BERD up as a loopback device. This information should

be included in the Work Order:

Physical Interface (10/100/1000BASE-T, 100BASE-FX, 1000BASE-SX, 1000BASE-LX,

10GBASE-LR, 40GBASE-SR4, 100GBASE-LR4, etc.)

Auto Negotiation settings of the port under test.

IP Address of the T-BERD running the RFC-2544 test

VLAN ID and Priority, if VLAN tagging is used.

Source IP Type (Static or DHCP)

If Source IP Type = Static:

oSource IP

oDefault Gateway

oSubnet Mask

2.2 Test Setup

Step Action Details

1. Power On Press and hold the ON/OFF button to turn on the T-BERD. For copper

testing with the T-BERD 5800v2, connect the Port 1 10/100/1000 RJ-45 jack

to the port under test using CAT 5E or better cable, and proceed to step 5.

For optical testing, or for copper testing on the T-BERD 5800-100G, proceed

to step 2.

2. Insert SFP Insert desired copper SFP, optical SFP, QSFP, or CFP4 into the

Port 1 slot on the top of the T-BERD.

3. Clean & Inspect Ensure the fiber and connectors are clean

using a Fiber Inspection probe.

4. Connect Connect the SFP, QSFP, or CFP4 to the port under test.

Use orange or aqua Multimode jumper cables

for 850 nm 1000BASE-SX or 10GBASE-SR.

Use yellow or dark blue Single Mode Fiber jumper

cables for 1310 nm 1000BASE-LX, 10GBASE-LR,

40GBASE-LR4, or 100GBASE-LR4.

Use CAT 5E or better cable for copper

10/100/1000BASE-TX connections.

Use 12-fiber MPO trunk cables for 40GBASE-SR4.

Use 24-fiber MPO trunk cables for 100GBASE-SR10.

Page 5 of 14

Technical Support [email protected] 1-844-468-4284

5. Load Test If a shortcut for this test is stored on the T-BERD, use the Test List to launch

the test and proceed to step 8.

6. All Test If the Select Test menu is hidden, tap to display the menu.

7. Select Test In the Select Test menu, ,at the top left corner of the screen,

choose one of the following:

For 10BASE-T, 100BASE-T, or 1000BASE-T Electrical Ethernet testing:

Ethernet

►

10/100/1000

►

Layer 3 Traffic

►

IPv4

►

Terminate or

Ethernet

►

10/100/1000

►

Layer 3 Traffic

►

IPv4

►

P1 Terminate.

For 100BASE-FX Optical Fast Ethernet testing:

Ethernet

►

100M Optical

►

Layer 3 Traffic

►

IPv4

►

Terminate or

Ethernet

►

100M Optical

►

Layer 3 Traffic

►

IPv4

►

P1 Terminate.

For 1000BASE-SR, 1000BASE-LR, or other GigE Optical Testing:

Ethernet

►

1GigE Optical

►

Layer 3 Traffic

►

IPv4

►

Terminate or

Ethernet

►

1GigE Optical

►

Layer 3 Traffic

►

IPv4

►

P1 Terminate.

For 10GBASE-SR, 10GBASE-LR, other 10GigE Optical Testing:

Ethernet

►

10GigE LAN

►

Layer 3 Traffic

►

IPv4

►

Terminate or

Ethernet

►

10GigE LAN

►

Layer 3 Traffic

►

IPv4

►

P1 Terminate.

For 40GBASE-SR4, 40GBASE-LR4, other 40GigE Optical Testing:

Ethernet

►

40GigE

►

Layer 3 Traffic

►

IPv4

►

Terminate or

Ethernet

►

40GigE

►

Layer 3 Traffic

►

IPv4

►

P1 Terminate.

For 1000GBASE-SR4, 40GBASE-LR4, other 40GigE Optical Testing:

Ethernet

►

100GigE

►

Layer 3 Traffic

►

IPv4

►

Terminate or

Ethernet

►

100GigE

►

Layer 3 Traffic

►

IPv4

►

P1 Terminate.

Page 6 of 14

Technical Support [email protected] 1-844-468-4284

8. Reset Test to Defaults In the Tools Panel, , select . Press to continue.

9. Setup Press the Setup Soft Key ,on the top right side of screen. Select the

indicated folders and configure your test as follows. Leave all other values at

default, unless specified in the Work Order.

Folder Option Value(s) Comment

Inerface,

Physical Layer Autonegotiation See Work Order

Ethernet

Encapsulation None or VLAN See Work Order

Data Mode IPoE

ARP Mode Enabled

Frame Type DIX

Length Type Packet Length

VLAN ID See Work Order If Encapsulation = VLAN,

tap to display settings.

User Priority 0

Source IP Type

Tap

to display settings

Source IP See Work Order

Default Gateway See Work Order

Subnet Mask See Work Order

Destination IP See Work Order

Page 7 of 14

Technical Support [email protected] 1-844-468-4284

10. Results Press the Results Soft Key, .

11. Turn Laser On For 1GigE, 10GigE, 40GigE, or 100GigE Optical tests, select the Laser tab

in the Actions panel, and press . The button will turn yellow and be

relabeled .

12. Restart Press the Restart Soft Key , on the right side of the screen.

13. Check LEDs A green Signal Present LED

●

indicates the

T-BERD is receiving an optical signal from the

Ethernet port under test. Green Sync Acquired

and Link Active LEDs indicate that the T-BERD

has successfully connected to the port under test

and the link is active.

The T-BERD is ready to be looped.

Page 8 of 14

Technical Support [email protected] 1-844-468-4284

3. T-BERD 5800 RFC-2544 Test Procedure

Follow this procedure to set up a T-BERD to run the Enhanced RFC 2544 Test.

3.1 Information requirements

The following information is required to set the T-BERD up to run the RFC 2544 Test. This information

should be included in the Work Order:

Physical Interface (10/100/1000BASE-T, 1000BASE-SX, 1000BASE-LX, 10GBASE-LR,

40GBASE-SR4, 100GBASE-LR4, etc.)

VLAN ID and Priority, if VLAN tagging is used.

Source IP Type (Static or DHCP)

If Source IP Type = Static:

oSource IP

oDefault Gateway

oSubnet Mask

Maximum Transmission Unit (MTU)

Committed Information Rate (CIR)

Pass/Fail Threshold for Throughput, Frame Loss, Latency and Jitter

3.2 Test Setup

Step Action Details

1. Power On Press and hold the ON/OFF button to turn on the T-BERD. For copper

testing with the T-BERD 5800v2, connect the Port 1 10/100/1000 RJ-45 jack

to the port under test using CAT 5E or better cable, and proceed to step 5.

For optical testing, or for copper testing on the T-BERD 5800-100G, proceed

to step 2.

2. Insert SFP Insert desired copper SFP, optical SFP, QSFP, or CFP4 into the

Port 1 slot on the top of the T-BERD.

3. Clean & Inspect Ensure the fiber and connectors are clean

using a Fiber Inspection probe.

4. Connect Connect the SFP, QSFP, CFP4 to the port under test.

Use orange or aqua Multimode jumper cables

for 850 nm 1000BASE-SX or 10GBASE-SR.

Use yellow or dark blue Single Mode Fiber jumper

cables for 1310 nm 1000BASE-LX, 10GBASE-LR,

40GBASE-LR4, or 100GBASE-LR4.

Use CAT 5E or better cable for copper

10/100/1000BASE-TX connections.

Use 12-fiber MPO trunk cables for 40GBASE-SR4.

Use 24-fiber MPO trunk cables for 100GBASE-SR10.

Page 9 of 14

Technical Support [email protected] 1-844-468-4284

5. Load Test If a shortcut for this test is stored on the T-BERD, use the Test List to launch the

test and proceed to Section 3.3.

6. All Test If the Select Test menu is hidden, tap to display the menu.

7. Select Test In the Select Test menu, ,at the top left corner of the screen,

choose one of the following:

For 10BASE-T, 100BASE-T, or 1000BASE-T Electrical Ethernet testing:

Ethernet►10/100/1000►RFC 2544►L3 Traffic IPv4►Terminate or

Ethernet►10/100/1000►RFC 2544►L3 Traffic IPv4►P1 Terminate.

For 100BASE-FX Optical Fast Ethernet testing:

Ethernet►100M Optical►RFC 2544►L3 Traffic IPv4►Terminate or

Ethernet►100M Optical►RFC 2544►L3 Traffic IPv4►P1 Terminate.

For 1000BASE-SR, 1000BASE-LR, or other GigE Optical Testing:

Ethernet►1GigE Optical►RFC 2544►L3 Traffic IPv4►Terminate or

Ethernet►1GigE Optical►RFC 2544►L3 Traffic IPv4►P1 Terminate.

For 10GBASE-SR, 10GBASE-LR, other 10GigE Optical Testing:

Ethernet►10GigE LAN►RFC 2544►L3 Traffic IPv4►Terminate or

Ethernet►10GigE LAN►RFC 2544►L3 Traffic IPv4►P1 Terminate.

For 40GBASE-SR4, 40GBASE-LR4, or other 40GigE Optical Testing:

Ethernet►40GigE►RFC 2544 ►L3 Traffic IPv4►Terminate or

Ethernet►40GigE►RFC 2544 ►L3 Traffic IPv4►P1 Terminate.

For 100GBASE-SR10, 100GBASE-LR4, or other 100GigE Testing:

Ethernet►10GigE►RFC 2544 ►L3 Traffic IPv4►Terminate or

Ethernet►10GigE►RFC 2544 ►L3 Traffic IPv4►P1 Terminate.

Page 10 of 14

Technical Support [email protected] 1-844-468-4284

3.3 Configuring RFC-2544 Test Settings

The RFC-2544 workflow consists of a series of screen that allow the user to configure the test, run the test,

and generate a report.

Figure 5: RFC-2544 GUI

Step Action Details

1. Configure If this is the first time using the RFC2544 test and your unit does not have

pre-loaded configuration files, tap the button next to “Start a New

Configuration (reset to defaults)” and proceed to step 2.

Otherwise, tap the button next to “Load Configuration from a

Profile”

Select the desired configuration, and tap .

Tap to acknowledge successful load

Tap the button

Tap the button next to Edit Configuration.

Autres manuels pour T-BERD 5800

Table des matières

Autres manuels Viavi Équipement de test

Viavi

Viavi OneExpert DSL Manuel utilisateur

Viavi

Viavi T-BERD/MTS-5800 OCC-4056C Manuel de la liste des pièces

Viavi

Viavi OTU-8000 Manuel de la liste des pièces

Viavi

Viavi SmartOTDR 100 Manuel utilisateur

Viavi

Viavi T-BERD 5800 Manuel utilisateur

Viavi

Viavi T-BERD/MTS 4000 V2 Manuel de la liste des pièces

Viavi

Viavi ComXpert CX100 Manuel utilisateur

Viavi

Viavi OneExpert CATV Manuel utilisateur

Viavi

Viavi Xgig Maestro Manuel de référence

Viavi

Viavi 3900 Series Manuel utilisateur

Viavi

Viavi T-BERD MTS 5800 Manuel utilisateur

Viavi

Viavi T-BERD MTS 5800 Manuel de la liste des pièces

Viavi

Viavi OneAdvisor ONA-800 Manuel utilisateur

Viavi

Viavi Smart Class 4800 Manuel utilisateur

Viavi

Viavi SmartClass Fiber OLS-85 Manuel utilisateur

Viavi

Viavi FCOMP/-PRO T-BERD/MTS-2000V2 Manuel utilisateur

Viavi

Viavi Certifier Series Manuel utilisateur

Viavi

Viavi OneAdvisor ONA-1000 400G Manuel technique

Viavi

Viavi 3550 Manuel du propriétaire

Viavi

Viavi 8800SX Manuel utilisateur

Viavi

Viavi T-BERD/MTS 5800 Manuel utilisateur

Viavi

Viavi MTS 2000 Manuel utilisateur

Viavi

Viavi T-BERD/MTS-2000 Manuel de la liste des pièces

Viavi

Viavi T-BERD/MTS 4000 V2 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur