Viavi HST-3000 Manuel utilisateur

Page 1 of 4

JDSU HST-3000

SAMComplete RFC-2544 and

Y.1564 Loopback

Version 1.0

February 27, 2014

Technical Support [email protected] 855-275-5378

Page 2 of 4

1. Hardware Description

The HST-3000 is a portable test tools for Ethernet testing. The product supports a variety of subscriber

interface modules (SIMs) to support Ethernet, T1/T3 and other access technologies. An Ethernet SIM

is required for this test. The HST-3000 works in conjunction with a fiber cleaning and inspection kit to

help turn-up and maintain Ethernet links. Menu selections are made from the HST-3000 front panel by

using the keypad to select the option number or by using the arrow keys to scroll to the desired

selection and pressing the OK key.

HST-3000 Front Panel:

Power Key

Second function key

Keypad

12 Buttons

Cancel Key

OK Key

Soft Keys

4 Keys

Status LEDs

LCD

Readable in

direct sunlight

Arrow keys

Microphone

Navigation Keys:

Configure, Home,

Autotest, System

Speaker

Ethernet and USB ports;

Headphone Jack

Technical Support [email protected] 855-275-5378

Page 3 of 4

User Interface:

2. HST-3000 Loopback

Use this procedure to set up an HST-3000 as a loopback device.

Step Action Details

1. Install SIM Install Ethernet Module on the HST-3000.

2. Power On Press the green Power Key to turn on the HST-3000. Wait

approximately 1 minute for the Base Unit software to load.

3. Insert SFP Insert desired SFP (1000BASE-SX, 1000BASE-LX, or 1000BASE-ZX)

into the optical SFP connector labeled R/T 1.

4. Clean & Inspect Ensure the fiber and connectors are clean using a Fiber Inspection probe.

5. Connect Connect the SFP to the Ethernet port under test.

•Use Orange Multimode jumper cables for

850 nm 1000BASE-SX.

•Use Yellow Single Mode Fiber jumper cables for

1310 nm 1000BASE-LX or 1550 nm1000BASE-ZX.

Technical Support [email protected] 855-275-5378

Page 4 of 4

6. Launch Test App Press the ETH OPTIC Soft key, select 1G Terminate, and press the

OK key. Select Layer 2 Traffic at the Test prompt

7. Configure Test Press the Configure Navigation key to configure test setting. Using the

Right Arrow key or Settings soft key, scroll through Settings menus

and configure your test as follows. Leave all other values at default,

unless specified in the Work Order.

8. View Results Press the Home key to display Summary Results.

9. Turn Laser On Press the Action soft key and select Laser On.

10. Restart Press the Restart soft key to reset test results.

11. Check LED Results Press the Right Arrow key until LED Results are displayed. A Green

Signal Present LED indicates that the HST-3000 is receiving an optical

signal from the near end Ethernet Switch. Green Sync Acquired and

Link Active LEDs indicate that the HST-3000 has successfully

connected to the near end Ethernet switch and the Ethernet link is active.

12. Test The HST-3000 is ready to be looped up.

Option

Value

Comment

Test Mode

Test

Layer 2 Traffic

Y.1564 Mode

Disable

SAM Complete

Disable

Link Init

Auto Negotiation

See Work Order

Set to same values as

Ethernet switch port.

Speed

See Work Order

Duplex

Full

Technical Support [email protected] 855-275-5378

Autres manuels pour HST-3000

Autres manuels Viavi Équipement de test

Viavi

Viavi AVX-10K Manuel utilisateur

Viavi

Viavi 8800SX Manuel utilisateur

Viavi

Viavi T-BERD/MTS 5800 Manuel utilisateur

Viavi

Viavi HST-3000 Manuel de la liste des pièces

Viavi

Viavi IFR 4000 Manuel de la liste des pièces

Viavi

Viavi HST-3000 Manuel utilisateur

Viavi

Viavi T-BERD 5800 Manuel utilisateur

Viavi

Viavi OneAdvisor ONA-1000 400G Manuel technique

Viavi

Viavi OLP-88 Manuel utilisateur

Viavi

Viavi MTS 2000 Manuel de la liste des pièces

Viavi

Viavi OneAdvisor ONA-800 Manuel utilisateur

Viavi

Viavi CT-X Manuel utilisateur

Viavi

Viavi COSA-4055 Manuel de la liste des pièces

Viavi

Viavi OneAdvisor-1000 Manuel utilisateur

Viavi

Viavi ALT-8000 Manuel de la liste des pièces

Viavi

Viavi ONX 580 Manuel utilisateur

Viavi

Viavi OneAdvisor ONA-800 Manuel de la liste des pièces

Viavi

Viavi PSD90-3 Manuel utilisateur

Viavi

Viavi HST-3000 Manuel de la liste des pièces

Viavi

Viavi IFR 6000 Manuel utilisateur

Viavi

Viavi HST-3000 Manuel utilisateur

Viavi

Viavi 8000 V2 Platform Manuel utilisateur

Viavi

Viavi ONX 580 Manuel utilisateur

Viavi

Viavi IFR 4000 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur