Viavi P5000i Manuel utilisateur

VIAVI//Public

P5000i Microscope

QUICK CARD

https://www.viavisolutions.com/en-us/products/fiber-inspection-cleaning

Standard Tips

FBPT-COD-L

FBPT-COD-MTA

FBPT-BAP1

Fiber Inspection with the SmartOTDR

This Quick Card outlines how to use the P5000i Fiber Inspection Microscope to inspect

common single mode fiber end faces.

EQUIPMENT REQUIREMENTS

Figure 1: Equipment Requirements

►SmartOTDR Handheld Fiber Tester

►P5000i Fiber Microscope

►Bulkhead and Patch Cord Inspection

Tips matching the fiber under test

►Fiber optic cleaning tools

Figure 2: P5000i, Barrel Assembly and Tips

1. Attached appropriate Inspection Tip to the front of

the P5000i by threading the collar of the tip onto

the probe:

►Standard Patch cord tips and Bulkhead tips

connect to the Barrel Assembly (FBPT-BAP1)

by loosening and tightening the Retaining Nut

on the BarrelAssembly.

►Ribbon tips and the Corning OptiTap Bulkhead tip

(FBPT-COD-L) connect directly to the probe.

2. Insert the P5000i USB Connector into a USB Port

under a flap on top of the SmartOTDR

Figure 3: P5000i and SmartOTDR

Retaining

nut

Interchangeable

Inspection tip

Focus

Control

Magnification

control

USB

Connector

Barrel

Assembly

Test Button

USB Ports under flaps

CONNECT P5000i TO SmartOTDR

VIAVI//Public

P5000i Microscope

QUICK CARD

1. Press the Home button to display the home screen.

2. Tap the Microscope icon.

3. Tap the Setup soft key .

4. Configure Tip Setting and Profile per the table below. If the Tip Selection is not shown on the

SmartOTDR, connect the SmartOTDR to a PC with FiberChekPRO™software using a USB to

MicroUSB cable and move the appropriate tip setting onto the SmartOTDR. For more information,

consult the FiberChekPRO user manual. To download FiberChekPRO to your PC, visit

http://fcpro.updatemyunit.net/.

SET UP THE P5000i

Connection Type Tip Profile Selection Tip Selection

LC Bulkhead SM UPC (IEC-61300-3-35 Ed. 2.0) Standard Tips (with BAP1)

Patch Cord SM UPC (IEC-61300-3-35 Ed. 2.0) Standard Tips (with BAP1)

SC-UPC Bulkhead SM UPC (IEC-61300-3-35 Ed. 2.0) Standard Tips (with BAP1)

Patch Cord SM UPC (IEC-61300-3-35 Ed. 2.0) Standard Tips (with BAP1)

SC-APC Bulkhead SM APC (IEC-61300-3-35 Ed. 2.0) Standard Tips (with BAP1)

Patch Cord SM APC (IEC-61300-3-35 Ed. 2.0) Standard Tips (with BAP1)

Corning

OptiTap Bulkhead SM APC (IEC-61300-3-35 Ed. 2.0) FBPT-COD-L

Patch Cord SM APC (IEC-61300-3-35 Ed. 2.0) Standard Tips (with BAP1)

Corning

OptiTip Bulkhead Ribbon, SM APC (IEC-61300-3-35 Ed. 2.0) Ribbon Tips

Patch Cord Ribbon, SM APC (IEC-61300-3-35 Ed. 2.0) Ribbon Tips

Figure 5:Test SetupFigure 4:Home Screen

VIAVI//Public

P5000i Microscope

QUICK CARD

INSPECT THE BULKHEAD

1. Set up the P5000i as described on page 2.

2. Press the Back soft key to return to the

inspection screen.

3. Insert the Bulkhead inspection tip into the Bulkhead.

►For SC-APC Bulkheads, align the keys on the

inspection tip and the bulkhead connector.

►For OptiTap Bulkheads, align the arc and

flat pin in the inspection tip to the matching

insertions inside the OptiTap receptacle adapter.

►For OptiTip Patch Cord Inspection, slide

the patch cord adapter onto the main tip assembly.

Rotate wheel to view and test each fiber.

4. Adjust the Focus Control wheel of the P5000i

microscope to focus the optical fiber. The top vertical

bar on the screen indicates the level of focus

adjustment. The higher the level, the better the focus.

The screen will display a line in the focus bar where

the optimal focus lies for that image. Focus the image

until the bar is as close to the line as possible.

5. There are 2 ways to run the inspection test:

►Press the Test button on the P5000i.

►Tap the Test soft key on the SmartOTDR.

6. A green checkmark indicates a PASS result. A red X

indicates a FAIL result.

7. Tap the Live soft key on the SmartOTDR to return to

the Live fiber view.

8. If the test failed, clean the fiber end-face and re-run the

inspection test. Repeat until it passes.

Figure 7: SC APC Bulkhead

Figure 8: OptiTap Bulkhead

Figure 9: OptiTip Bulkhead

Figure 11: Pass/Fail Analysis

Figure 10: Live Inspection

Figure 6: LC Bulkhead

VIAVI//Public

P5000i Microscope

QUICK CARD

Product specifications and descriptions in this

document are subject to change without notice.

Patented as described at viavisolutions.com/patents

To reach the VIAVI office nearest you,

visit viavisolutions.com/contact

+1 844 GO VIAVI

(+1 844 468-4284)

INSPECT THE PATCH CORD

1. Insert the Patch Cord into the Inspection tip:

➢For SC-APC Patch Cord inspection through an SC-SC Optical

Coupler, insert the Patch Cord into the SC APC optical coupler.

The Patch Cord, coupler, and tip are all keyed and the keys must

be aligned.

➢For OptiTap and SC-APC Patch Cord Inspection without an Optical

Coupler, insert the Patch Cord into the 2.5mm APC Patch Cord

inspection tip. Rotate fiber and align the connector key to the notch

on inspection tip for proper alignment.

➢For OptiTip Patch Cord Inspection, slide the bulkhead adapter onto

the main tip assembly. Rotate wheel to view and test each fiber.

2. Set up the P5000i as described on page 2.

3. Press the Back soft key to return to the

inspection screen.

4. Adjust the Focus Control wheel of the P5000i

microscope to focus the optical fiber.

5. There are 2 ways to run the inspection test:

►Press the Test button on the P5000i.

►Tap the Test soft key on the SmartOTDR.

6. A green checkmark indicates a PASS result.

A red Xindicates a FAIL result.

7. Tap the Live soft key on the SmartOTDR to return

to the Live fiber view.

8. If the test failed, clean the fiber end-face and re-run

the inspection test. Repeat until it passes.

Figure 12:

SC APC Patch Cord and Coupler

Figure 13: SC APC Patch Cord

Figure 14: OptiTap Patch Cord

Figure 15: OptiTip Patch Cord

Figure 16: Pass/Fail Analysis

Figure 15: Live Inspection

Autres manuels pour P5000i

Autres manuels Viavi Microscope

Viavi

Viavi P5000i Manuel de la liste des pièces

Viavi

Viavi FVAm Series Manuel utilisateur

Viavi

Viavi FiberChek Manuel de la liste des pièces

Viavi

Viavi INX 760 Manuel utilisateur

Viavi

Viavi P5000i Manuel de la liste des pièces

Viavi

Viavi OneAdvisor ONA-800 Manuel de la liste des pièces

Viavi

Viavi P5000i Manuel de la liste des pièces

Viavi

Viavi FiberChek Manuel utilisateur

Viavi

Viavi FiberChek Manuel utilisateur

Viavi

Viavi FVAi-2030 Manuel utilisateur

Manuels Microscope populaires d'autres marques

Thermo Scientific

Thermo Scientific Nicolet iN10 Mode d’emploi

National

National DC3-163 Manuel utilisateur

KERN Optics

KERN Optics OPE-1 Manuel utilisateur

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuel utilisateur

Prior

Prior Lux POL Manuel utilisateur

Opitec

Opitec Smartscoop 115615 Manuel utilisateur

KERN

KERN OPO-1 Manuel utilisateur

Topcon

Topcon SP-1P Manuel utilisateur

Motic

Motic PA43 Manuel utilisateur

Leica

Leica DVM5000 Guide de l'utilisateur

MshOt

MshOt MZ62 Manuel utilisateur

KERN Optics

KERN Optics OZR-5 Manuel utilisateur

VWR

VWR VisiScope 384 Series Manuel utilisateur

Nikon

Nikon ECLIPSE E200 POL Manuel utilisateur

Leica

Leica DI C800 Manuel

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuel utilisateur

Olympus

Olympus SZ61 Manuel utilisateur