Viavi DSP TDR Manuel utilisateur

DSP TDR

Quick Start Guide

DSP TDR Quick Start Guide

22134505, Rev. 000 July 2019ii

Notice

Every effort was made to ensure that the information in this manual was accurate at the time

of printing. However, information is subject to change without notice, and VIAVI reserves the

right to provide an addendum to this manual with information not available at the time that

this manual was created.

reproduced or transmitted, electronically or otherwise, without written permission of the

publisher. VIAVI Solutions and the VIAVI logo are trademarks of VIAVI Solutions Inc. (“Viavi”). All

other trademarks and registered trademarks are the property of their respective owners.

Reproduction and distribution of this guide is authorized for US Government purposes only.

Ordering information

This guide is a product of the VIAVI Technical Publications Department, issued as part of the

product. The catalog number for a published guide is Catalog Number - printed. The catalog

number for an electronic guide on USB is Catalog Number - electronic.

Terms and conditions

Specifications, terms, and conditions are subject to change without notice. The provision

of hardware, services, and/or software are subject to VIAVI standard terms and conditions,

available at www.viavisolutions.com/en/terms-and-conditions.

Federal Communications Commission (FCC) Notice

This product was tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This product generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. Operation of this product in a residential area is likely to cause

harmful interference, in which case you will be required to correct the interference at your own

expense.

The authority to operate this product is conditioned by the requirements that no modifications

be made to the equipment unless the changes or modifications are expressly approved by

VIAVI.

DSP TDR Quick Start Guide

22134505, Rev. 000July 2019 iii

CAUTION:

• To comply with FCC RF exposure compliance requirements, a separation distance of at

least 20 cm must be maintained between the antenna of this device and all persons.

• This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

EU WEEE and Battery Directives

This product, and the batteries used to power the product, should not be disposed of as

unsorted municipal waste and should be collected separately and disposed of according to

your national regulations.

VIAVI has established a take-back process in compliance with the EU Waste Electrical and

Electronic Equipment (WEEE) Directive, 2012/19/EU, and the EU Battery Directive, 2006/66/EC.

Instructions for returning waste equipment and batteries to VIAVI can be found in the WEEE

section of the VIAVI Standards and Policies web page.

If you have questions concerning disposal of your equipment or batteries, contact the VIAVI

WEEE Program Management team at WEEE.EMEA@ViaviSolutions.com.

EU REACH

Article 33 of EU REACH regulation (EC) No 1907/2006 requires article suppliers to provide

information if a listed Substance of Very High Concern (SVHC) is present in an article above a

certain threshold.

For information on the presence of REACH SVHCs in VIAVI products, see the Hazardous

Substance Control section of the VIAVI Standards and Policies web page.

EU CE Marking Directives (LV, EMC, RoHS, RE)

This product conforms with all applicable CE marking directives. For details, please see the EU

Declaration of Conformity included in the shipping package.

California Proposition 65

California Proposition 65, officially known as the Safe Drinking Water and Toxic Enforcement

Act of 1986, was enacted in November 1986 with the aim of protecting individuals in the

state of California and the state’s drinking water and environment from excessive exposure to

chemicals known to the state to cause cancer, birth defects or other reproductive harm.

For the VIAVI position statement on the use of Proposition 65 chemicals in VIAVI products, see

the Hazardous Substance Control section of the VIAVI Standards and Policies web page.

DSP TDR Quick Start Guide

22134505, Rev. 000 July 2019iv

Conventions

This guide uses typographical and symbols conventions as described in the following tables.

Description Example

User interface actions On the Status bar, press Start.

Buttons or switches that you press

on a unit Press the ON switch.

Code and output messages All results okay

Text you must type exactly as

shown Type: a:\set.exe in the dialog box

Variables Type the new hostname.

Book references Refer to Newton’s Telecom Dictionary

A vertical bar | means “or”: only

one option can appear in a single

command.

platform [a|b|e]

Square brackets [ ] indicate an

optional argument. login [platform name]

Slanted brackets < > group

required arguments. <password>

Description Example

A plus sign + indicates

simultaneous keystrokes. Press Ctrl+s

A comma indicates consecutive key

strokes. Press Alt+f,s

A slanted bracket indicates

choosing a submenu from menu. On the menu bar, press Start > Program Files.

Typographical conventions

Keyboard and menu conventions

DSP TDR Quick Start Guide

22134505, Rev. 000July 2019 v

Symbol conventions

This symbol indicates a note that includes important supplemental information or

tips related to the main text.

This symbol represents a general hazard. It may be associated with either a

DANGER, WARNING, CAUTION, or ALERT message. See "Safety Definitions" on

page vi for more information.

This symbol represents an alert. It indicates that there is an action that must be

performed in order to protect equipment and data or to avoid software damage

and service interruption.

This symbol represents hazardous voltages. It may be associated with either a

DANGER, WARNING, CAUTION, or ALERT message. See "Safety Definitions" on

page vi for more information.

This symbol represents a risk of explosion. It may be associated with either a

DANGER, WARNING, CAUTION or ALERT message. See "Safety Definitions" on

page vi for more information.

This symbol represents a risk of a hot surface. It may be associated with either

a DANGER, WARNING, CAUTION, or ALERT message. See "Safety Definitions" on

page vi for more information.

This symbol represents a risk associated with fiber optic lasers. It may be

associated with either a DANGER, WARNING, CAUTION or ALERT message. See

"Safety Definitions" on page vi for more information.

This symbol, located on the equipment, battery, or the packaging indicates

that the equipment or battery must not be disposed of in a land-fill site or

as municipal waste, and should be disposed of according to your national

regulations.

DSP TDR Quick Start Guide

22134505, Rev. 000 July 2019vi

Safety definitions

Term Description

DANGER

Indicates a potentially hazardous situation that, if

not avoided, will result in death or serious injury. It

may be associated with either a general hazard, high

voltage, or other symbol.

WARNING

Indicates a potentially hazardous situation that, if

not avoided, could result in death or serious injury. It

may be associated with either a general hazard, high

voltage, or other symbol.

CAUTION

Indicates a potentially hazardous situation that, if not

avoided, could result in minor or moderate injury and/

or damage to equipment.

It may be associated with either a general hazard,

high voltage, or risk of explosion symbol.

When applied to software actions, indicates a

situation that, if not avoided, could result in loss of

data or a disruption of software operation.

ALERT

Indicates that there is an action that must be

performed in order to protect equipment and data or

to avoid software damage and service interruption.

DSP TDR Quick Start Guide

22134505, Rev. 000July 2019 vii

Precautions

WARNING:

The maximum “RF” input voltage to the meter is 125 Volts

(AC or DC). A larger voltage will damage the meter.

WARNING:

Pursuant to FCC 15.21 of the FCC rules, changes not

expressly approved by VIAVI might cause harmful

interference and void the FCC authorization to operate this

product.

WARNING:

The antenna used for this instrument is installed at the

VIAVI factory or by VIAVI-approved repair facilities. During

operation of the device, a distance of 20 cm or more should

be maintained between the antenna in this device and person.

To ensure compliance, do not operate at closer distances

than this. The antenna on the unit is located inside the device

at the top of the unit attached to the back plastic case. Do not

use any antenna other than the installed antenna.

CAUTION:

Do not use the instrument in any manner not recommended

by the manufacturer.

CAUTION:

A strong electromagnetic eld may affect the measurement

accuracy of the meter.

DSP TDR Quick Start Guide

22134505, Rev. 000 July 2019viii

Precautions (continued)

CAUTION:

Use only the battery charger supplied with the meter. Use of

any other charger may damage the battery.

NOTE:

Damage caused by improper cleaning of the display screen

will void the warranty of the unit.

NOTE:

Never use abrasive pads, paper towels, tissue paper, or

clothing to wipe the screen. If you do, these non-ultrasoft

materials can cause permanent damage by scratching the

screen or stripping the anti-glare coating off the screen.

NOTE:

Never use any type of window cleaner, soap, scouring powder,

or any cleanser with solvents such as alcohol, benzene,

ammonia, or paint thinner. These chemicals can react with

the materials used to construct the display which can lead to

hazing, yellowing, brittleness, or other types of damage.

ALERT:

Never spray liquid directly on the display screen as it could

run inside the unit and cause damage.

DSP TDR Quick Start Guide

22134505, Rev. 000July 2019 1

Before You Begin

Thank you for purchasing the DSP TDR. This guide provides setup and operating instructions to

get you up and running as soon as possible.

Technical Assistance

If you require technical assistance, call 1-844-GO-VIAVI / 1.844.468.4284.

Outside US: +1-855-275-5378

Email: Trilithic.support@viavisolutions.com

For the latest TAC information, visit

https://support.viavisolutions.com/welcome

DSP TDR Quick Start Guide

22134505, Rev. 000 July 20192

About the DSP TDR

In the event of a cable break or fault, the DSP TDR enables cable service provider maintenance

teams and contractors to quickly find the location to get service back online as soon as

possible. Since a cable break likely means an outage, pin-pointing it quickly is very important.

Length measurement accuracy is also critically important, as often the cable is underground

and must be dug out to make the splice. A lack of precision in this measurement means a

bigger hole must be dug. A TDR is needed to find breaks and faults, to keep the operator from

paying for unnecessary span replacements.

The DSP TDR is designed for field use and has step technology, which enables it to show

smaller faults, has no blind spot, and maintains accuracy for detecting impedance over the

entire length of the cable. Automatic impedance matching allows for faster trace results

without pulse width adjustments. In addition to the ability to find faults closer to the TDR (no

blind spot) the TDR has a resolution of less than 1 foot (0.3m). The higher energy step TDR has

an improved signal-to-noise ratio and digital averaging, eliminating noise interference, and

producing a much more detailed cable image than available with a pulse TDR.

Benefits

• Reduce outage and line problem troubleshooting time

• Features fast, complete, and precise measurements without blind spots

• Data upload and retention with StrataSync

• Built to last design for use in the real environment of Network Technicians

• Long battery life

TDR screen, showcasing step technology Events listed with trace in StrataSync

Table des matières

Autres manuels Viavi Instrument de mesure

Viavi

Viavi WiFi Advisor WFED-300AC Manuel utilisateur

Viavi

Viavi SmartPocket OLP-35V2 Manuel utilisateur

Viavi

Viavi E4123MM Manuel utilisateur

Viavi

Viavi Xgig Manuel utilisateur

Viavi

Viavi G3-GSP-8P-8TSSD Manuel

Viavi

Viavi SmartClass ORL-85 Manuel utilisateur

Viavi

Viavi CPRIAdvisor CAP-100 Manuel utilisateur

Viavi

Viavi ONX-220 Manuel utilisateur

Viavi

Viavi ALT-8000 Manuel de la liste des pièces

Viavi

Viavi CAA06M Manuel utilisateur

Viavi

Viavi SmartPocket OLP-37XV2 Manuel utilisateur

Viavi

Viavi Observer GigaStor GS-4P-16T Manuel

Viavi

Viavi ALT-8000 Manuel utilisateur

Viavi

Viavi MP-60 Manuel de la liste des pièces

Viavi

Viavi CellAdvisor 5G Manuel utilisateur

Viavi

Viavi MPOL*-85P Manuel utilisateur

Viavi

Viavi SmartClass Fiber OLS-85 Manuel utilisateur

Viavi

Viavi FBP-SD4I-PRO Manuel utilisateur

Viavi

Viavi WiFi Advisor WFED-300AC Manuel utilisateur

Viavi

Viavi OneExpert CATV Manuel utilisateur

Viavi

Viavi SmartClass OLP-87 Manuel utilisateur

Viavi

Viavi G3-GSP-2P100-8TSSD Manuel

Viavi

Viavi OLS-34 Manuel utilisateur

Viavi

Viavi G4-PT-040-8T Manuel

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur