Vestil UNI Manuel utilisateur

02/05 03-126-121.doc

VESTIL MFG.CO. 1

VESTIL MANUFACTURING CORP.

2999 N. Wayne St., Angola, IN 46703

Ph: 260-665-7586 · Fax: 260-665-1339

E-mail: [email protected] Website: www.vestil.com

MODEL UNI

Serial number ____________

Installation Instructions ……………….....................… 2

Operation Instructions ……………………….……… 3-4

Routine Maintenance & Safety Checks ……………… 5

Exploded Structural Parts Drawing & BOM ………... 6-7

Motor and Transformer Connections ............................ 8

Electrical & Hydraulic Diagrams & BOM ………….. 9-10

Power Unit’s Operation ………………...…..………... 11

Troubleshooting …………………………....………… 12

Safety Label Identification .............................................13

Warranty …………………………………….……..…. 14

IMPORTANT NOTES,WARNINGS AND SAFETY INSTRUCTIONS

Ensure that all employees understand and follow the following.

oRead and understand the owner’s manual before using or servicing

the Uni-Tilt.

oThe load must be removed and the platform supported or fully

lowered before any work is performed on the lift.

oEnsure that all safety and warning labels stay in place and are

legible.

oDo not use the Uni-Tilt if any damage or unusual noise is observed.

oAlways watch the platform and the container carefully when the

tilter is in operation.

oDo not transport the Uni-Tilt with any load on the platform.

oDo not use brake fluid or jack oils in the hydraulic system. If oil is

needed, use an anti-wear hydraulic oil with a viscosity grade of

150 SUS at 100°F, (ISO 32 cSt @ 40°C), or Dexron transmission fluid.

oContact the manufacturer for any needed MSDS information.

♦Do not perform any modifications to the Uni-Tilt without the

manufacturer’s approval. Failure to receive authorization for

changes to the equipment could void the warranty.

♦Maintenance and repairs are to be done only by personnel qualified

to perform the required work. Warranty labor charges will not

receive consideration without prior written authorization by the

manufacturer.

WHEN ORDERING

REPLACEMENT PARTS:

We take pride in using quality

parts on the equipment we

manufacture. We are not

responsible for equipment

problems resulting from the use

of unapproved replacement

parts.

To order replacement or

spare parts for this equipment,

contact the factory.

In any communication with

the factory please be prepared

to provide the machine’s serial

number, which is indicated on

the machine dataplate.

RECEIVING INSTRUCTIONS

Every unit is thoroughly

tested and inspected prior to

shipment. However, it is

possible that the unit could

incur damage during transit.

Inspect the unit closely when

it arrives. If you see evidence

of damage or rough handling to

either the packaging or to the

product when it is being

unloaded, immediately make a

note of it on the Bill Of Lading!

It is important that you

remove the product’s packaging

upon its arrival to ensure that

there is no concealed damage

or to enable a timely claim with

the carrier for freight damage.

Also verify that the product

and its specifications are as

ordered.

WNER

’

MANUAL

02/05 03-126-121.doc

VESTIL MFG.CO. 2

INSTALLATION INSTRUCTIONS –UNI

Review this entire page before installing the Uni-Tilt.

Consult the factory in the event there are any questions or problems at the time of installation, or for

information regarding optional features not covered by the owner’s manual.

•Modifications or additions to the Uni-Tilt without prior manufacturer’s authorization may void the unit’s warranty.

The addition of ancillary equipment to the platform may necessitate that its load capacity be reduced.

•The installation must be made so that it complies with all the regulations applicable to the machine and its

location. The end-user must verify that the supplied equipment is installed so it will be suited to the environment

in which it will be used.

•Installation must be performed by suitably trained personnel with access to the appropriate equipment. The

electrical aspects of the installation should be performed by an electrician.

---------------------------------------------------------------------------------------

For a typical installation you will need the following:

1. A fork truck or hoisting means to unload the Uni-Tilt from the freight truck and set it into place.

2. A smooth, level, and adequately strong concrete surface on which to mount and operate the Uni-Tilt.

3. Concrete anchors, a masonry drill, a masonry bit, hand tools, grout, and steel shims. Consult the building’s

architect or facility engineer to determine the best size and type of hardware with which to anchor the machine to

the floor.

•Portable units do not need to be anchored to the floor.

4. A power supply circuit and electrical disconnect matching the motor voltage and current requirements. Refer to

the machine’s dataplate, to the labels on the control enclosure, and to the electrical section in this manual for

more information. The end-user is responsible for supplying the branch circuit’s required ground fault and short-

circuit protection. (Motor overload protection is provided by a thermostat built into the motor.)

---------------------------------------

1. Move the tilter into place with a fork truck having at least a 2,000 lb capacity.

2. Temporarily connect the power supply to the pigtail cord supplied with the Uni-tilt, and raise the platform so the

unit’s safety maintenance prop(s) can be utilized. Lower the platform so the unit is supported by the prop(s).

oThe maintenance prop(s) is located in the Uni-tilt’s frame next to the lifting assembly. It is a rod with a 90° bend.

To install the prop(s), raise the platform to its full raised height and insert the longer end through the holes in the

frame roller weldment. Lower the frame roller assembly unit it rests on the prop.

oIf the platform must be raised without first having the proper power supply connected, raise the platform at the

side of the table opposite the platform cradle. Use rigging or insert a lift truck’s forks under the front edge of the

platform to tilt the platform up. Hold the frame down at the ends of the shipping 4 x 4’s on the hinged side of the

Uni-tilt while the platform is raised.

3. Anchor the frame to the floor through the holes located at the frame’s corners. (Non-portable units only.)

4. Make permanent connection to the power supply, using an appropriate wiring method.

5. Operate the Uni-Tilt through several full raise and lower cycles. Verify that the upper travel limit switch functions

properly.

6. Check the hydraulic oil level. It should be filled to within 1” to 1½” of the reservoir’s fill hole. If oil is needed,

use an anti-wear hydraulic oil with a viscosity grade of 150 SUS at 100°F (ISO 32 at 40°C) or a non-synthetic

automatic transmission fluid.

7. Clean up any debris or spilled oil, and verify that all of the warning and safety labels are intact.

02/05 03-126-121.doc

VESTIL MFG.CO. 3

OPERATION INSTRUCTIONS –UNI

oConsult ANSI MH29.2 - 2000, Safety Requirements for Industrial Tilters, Section 12, for the owner’s / user’s

responsibilities regarding the operation, care, and maintenance of this machine.

oEnsure that all employees involved in the operation of this machine understand and follow these instructions!

The standard model UNI (stationary) and UNI-P (portable) is suitable for use indoors in most industrial locations and

many commercial locations. It is intended to be used to lift and tilt stable, non-hazardous loads and containers having

a size or footprint approximately the same size as the platform.

Loading:

The load rating, in pounds, is shown on the machine dataplate located on the right front corner of the loading

(opposite the backstop) side of the platform . It indicates the net capacity of the machine, with a static load that is

centered and evenly distributed on the platform and having a vertical center of gravity not more than 20” above the

platform surface.

For applications involving side loading or loads with higher centers of gravity, consult the manufacturer.

The standard design Uni-Tilt is intended to be loaded with a fork truck or similar material handling equipment.

Always center the load, and place it up against the back cradle of the platform to prevent sudden load shifting when

the platform is tilted.

Do not exceed a rate of two feet per second when moving loads onto the platform.

Note: The addition of any ancillary equipment to the platform by third parties must be taken into account when

determining the maximum working load to be placed on the platform.

Warning: Do not exceed the Uni-tilt’s load ratings. Injury to personnel or permanent damage to the structure could

result from exceeding the listed capacity.

Operation:

Warning: Keep all personnel clear of the machine when it is in operation. Be certain no part of any person or object is

under any part of the platform before lowering the unit.

Caution: Always carefully watch the container and any load in it when it is in operation.

To raise or tilt the platform back toward the operator, press the “UP” pushbutton.

To lower or tilt the platform toward the floor, press the “DN” pushbutton.

When a pushbutton is not being pressed, the unit will hold its position wherever it is in its travel range.

The Uni-tilt can be operated in either one of two movement sequences.

•Sequence #1:

•Starting with the platform in the fully lowered position, press and hold the “UP” pushbutton while you push the

sequence selector pedal in against the frame of the table with your foot. After about five seconds, the pedal can

be released.

•The platform will tilt back toward the operator until it reaches a tilt angle of 40° to the floor. It then will lift

vertically until the bottom of the cradle reaches a height of 16½” above the floor.

•To lower the platform, press and hold the “DN” pushbutton. The platform will drop vertically until the bottom of

the cradle is about 12” above the floor, and then the platform will tilt down away from the operator until it is

again fully collapsed and level with the floor.

•Sequence #2:

•Again starting with the platform in the fully lowered position, press and hold the “UP” pushbutton. (Do not press

the sequence selector pedal.) The platform will rise and tilt back at the same time, until it reaches a height of 19”

from the floor to the bottom of the cradle and a tilt angle of 35°.

•To return to the fully collapsed position, press and hold the “DN” pushbutton. The platform will both lower and

tilt down towards the floor concurrently until the unit is again fully collapsed and level with the floor.

On DC-powered units, attempting to raise the lift when the battery is low will cause the motor relay protection to

prevent the motor’s operation. Adequate battery voltage is indicated by a green LED on the motor relay. See the next

page for more notes regarding operation of battery-powered units.

Ensure that all safety and warning labels stay in place and are legible. Refer to the labels page in this manual.

02/05 03-126-121.doc

VESTIL MFG.CO. 4

ADDITIONAL INSTRUCTIONS FOR BATTERY-POWERED UNITS

Warning!

!Working with or near lead acid batteries is dangerous. Batteries contain sulfuric acid and produce explosive gases.

A battery explosion could result in loss of eyesight or serious burns.

!Do not smoke or allow a spark or flame near batteries. Charge batteries in locations that are clean, dry, and well

ventilated. Do not lay tools or anything metallic on top of any battery. All repairs to a battery must be made by

experienced and qualified personnel.

!When working with batteries, remove personal items such as rings, bracelets, necklaces, and watches. Batteries

can produce enough energy to weld jewelry to metal, causing a severe burn.

!Always have fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.

!Operating the battery with a low battery voltage can cause premature motor contact failure.

!Do not expose the lift or charger to rain or adverse conditions.

!Replace defective cords or wires immediately.

!Check the battery’s water level frequently.

Battery Charger Operating Instructions

Never operate the charger with either of the cables coiled. Operating a battery charger with the cord either coiled

or wrapped around itself could cause the cord to overheat, melt, and cause a short-circuit or a fire.

Connection: the ribbed wire of the charger’s output cord must be connected to the battery’s negative (-) terminal.

The non-ribbed wire (with words printed on it) must be connected to the battery’s positive (+) terminal.

When properly connected, the charger will indicate the status of charger output:

Flashing green LED – the charger is not seeing a good connection to the battery.

Solid yellow LED – the charger is providing charging current to the battery.

Solid green LED – the charger is maintaining a fully charged battery.

Plug the charger into a standard 115V receptacle. If an extension cord must be used, keep it as short as possible.

Caution: Remember to unplug the charger before moving the equipment. Failure to do so could cause damage to

cords, receptacles, and other equipment.

The battery charger can be left connected to the battery indefinitely without risk of harming the battery.

Troubleshooting:

If the unit does not operate, check all of the wiring connections to make sure they’re both mechanically and

electrically sound – specifically at the battery, the motor, and at any location a wire is connected to the chassis.

Also, make sure the quick-connect plug on the end of the pendant control cord is plugged in correctly (if

applicable).

A fully charged lead acid battery in good condition at room temperature should read 12.65 volts. At 11.9 volts it is

considered to be fully discharged and in need of charging. When checking battery voltage, wait at least 1/2 hour

after the charger has been turned off before checking the battery’s voltage.

If the batteries don’t seem to be taking a charge, check the charger’s 115V supply circuit and the charger’s output

with a voltmeter. If all check okay, confirm the battery’s state of charge using a hydrometer or a voltmeter.

02/05 03-126-121.doc

VESTIL MFG.CO. 5

ROUTINE MAINTENANCE &SAFETY CHECKS –UNI

oWarning: Care should be taken to identify all potential hazards and comply with applicable safety procedures

before beginning work.

oWarning: Raise the platform and install the maintenance props before beginning any inspections or work on the

unit.

oOnly qualified individuals trained to understand mechanical devices and their associated electrical and hydraulic

circuits should attempt troubleshooting and repair of this equipment

(A) Before each use inspect for the following:

1.) Frayed wires

2.) Oil leaks

3.) Pinched or chafed hoses

4.) Damage or structural deformation to the structural members, the cylinder brackets, etc.

5.) Unusual noise or binding, or evidence thereof.

6.) Proper functioning of all limit switches, including those on the perimeter pinch point guard (if applicable).

(B) Inspect monthly for:

1.) The oil level. Oil should be 1½” to 2” below the reservoir’s fill hole with the lift in the fully raised position.

See below for oil specification.

2.) Worn or damaged hydraulic hoses and electrical wires.

3.) Pivot point wear.

4.) Rollers’ looseness and wear.

5.) Integrity of the retaining rings on all rollers and on all pivot point pins.

6.) The integrity of the frame anchor bolts, and for cracks in the concrete around them.

(Non-portable units only.)

7.) Damage or evidence of fatiguing to the fork tubes. (Portable units only.)

8.) Proper functioning of the foot-operated sequencing mechanism.

9.) Proper water level in the battery (DC units only.)

10.) Unusual noises or movement during operation.

11.) All the information, safety, and warning labels being in place and in good condition.

12.) The need to clean off dirt and debris.

The oil should be changed if the oil darkens, becomes gritty, or turns a milky color (indicating the presence of water).

Replace with an anti-wear hydraulic oil with a viscosity grade of 150 SUS at 100°F, (ISO 32 at 40°C). Ex: AW 32 or HO

150 hydraulic oil, or a non-synthetic transmission fluid. You may use a synthetic transmission fluid if you flush the

system with the synthetic fluid before filling the reservoir.

02/05 03-126-121.doc

VESTIL MFG.CO. 6

EXPLODED PARTS VIEW -- UNI

02/05 03-126-121.doc

VESTIL MFG.CO. 7

BILL OF MATERIALS -- UNI

Item #: Description Part number Qty.

1 Weldment assembly, back leg 03-510-001 1

2 Weldment assembly, front leg 03-510-002 1

3 Weldment assembly, deck 03-513-035 1

4 Weldment assembly, frame 03-514-022 1

5 Cylinder, hydraulic, 3” x 10” displacement-style 99-021-901 1 or 2

6 Snap ring, external, 11/8”Ø A/L 10

7 Weldment assembly, foot lever mode selector arm 03-540-003 1

8 Pin, hinge, 11/8”Ø x 113/16” long 01-112-004 4

9 Bolt, cylinder retainer 01-118-001 2

10 Pin, roll,

3/16”Ø x 11/8” long A/L 2

11 Bushing, machine, 11/8” ID x 13/4” OD x 18 gauge A/L 6

12 Roller assembly, w/ bushing, 31/4” OD x 11/8” ID 01-527-001 2

13 Nut, jam, ½-13 UNC A/L 2

14 Pin, w/ stop boss, 11/8” OD x 91/4” long 01-112-001 1

15 Pin, roller, 11/8” OD x 95/16” long 03-112-002 1

16 Pin, cylinder clevis w/ stop boss, 11/8” OD x 73/4” long 01-112-015 1

17 Screw,

5/16”-16 UNC x 31/2” long HHCS A/L 1

18 Weldment assembly, foot lever push rod 03-540-004 1

19 Stop, wheel 03-037-001 2

20 Screw, grade 5, ½”-13 UNC x 11/2” long HHCS A/L 4

21 Weldment assembly, foot lever pedal 03-540-004 1

22 Nut, nylock, ½”-13 UNC A/L 4

23 Nut,

3/8”-16 UNC hex A/L 1

24 Screw,

5/16”-18 UNC x 11/2” long HHCS A/L 1

25 Nut, 5/16”-18 UNC hex A/L 2

26 Pin, maintenance 03-130-001 1

27 Guard, vinyl, 16” wide x 38” long A/L 1

28 Rivet, blind A/L 10

02/05 03-126-121.doc

VESTIL MFG.CO. 8

MOTOR &TRANSFORMER CONNECTION DIAGRAMS

CAUTION!If the motor voltage is changed, the wire on the control transformer’s primary wire has to be changed to

match the new motor voltage also.

02/05 03-126-121.doc

VESTIL MFG.CO. 9

ELECTRICAL DIAGRAM -- UNI

oWarning: Care should be taken to identify all potential hazards and comply with applicable safety procedures before

beginning work. Fully lower or secure the platform with the maintenance props, and ensure that all system

pressure and power have been removed, before attempting to work on the electrical or hydraulic systems.

oRaise the platform and install the maintenance props before beginning inspections or work on the unit.

oOnly qualified individuals trained to understand mechanical devices and their associated electrical and hydraulic

circuits should attempt troubleshooting and repair of this equipment

02/05 03-126-121.doc

VESTIL MFG.CO. 10

HYDRAULIC DIAGRAM –LIFT-HOLD-LOWER CIRCUITS

oWarning: Care should be taken to identify all potential hazards and comply with applicable safety procedures

before beginning work. Fully lower or secure the platform, and ensure that all system pressure and power have

been removed, before attempting to work on the electrical or hydraulic systems.

oOnly qualified individuals trained to understand mechanical devices and their associated electrical and hydraulic

circuits should attempt troubleshooting and repair of this equipment

oCaution: Do not use brake fluid or jack oils in the hydraulic system. If oil is needed, use an anti-wear hydraulic

oil with a viscosity of 150 SUS at 100°F (ISO 32 @ 40°C), or non-synthetic transmission fluid.

ELECTRIC /HYDRAULIC BOM –UNI

Item #: Qty.: Part number: Part description:

Electrical parts:

1 1 01-135-XXX Motor; varies by customer spec; contact factory

2 1 LC1-D1810-24V Motor contactor, 30A, w/ 24 VAC coil

3 1 01-129-001 Transformer, control; w/ 24 VAC secondary

4 1 AGC 2 Fuse, for control circuit

5 1 01-029-006 Control enclosure, 6” W x 6” L x 4” D

6 1 01-522-015 Pushbutton control on 8’ cord

7 1 99-034-008 Solenoid coil, 24 VAC

8 1 01-033-017 Connector cord, for solenoid coil

9 1 01-033-015 Cord, power, 14/3, 9’ long, w/ NEMA 5-15 plug (115V units)

10 1 01-022-001 Limit switch, roller-arm (N.C.)

11 1 01-033-002 Cable, 18/2 coil cord, 12”-60” (to toe guard switches)

12 2 159/D Multi-pole terminal strip

Hydraulic parts:

13 1 99-153-006 Valve, relief, 210 bar

14 1 99-153-015 Valve, solenoid, N.C.

15 1 99-153-011 Valve, check

16 1 99-153-040 Flow control spool, 2 gpm

17 1 or 2 99-021-XXX Cylinder, displacement; varies by model; contact factory

18 1 or 2 99-136-XXX Cylinder seal kit; varies by model; contact factory

19 1 99-127-001 Manifold, lift-hold-lower

20 1 01-143-XXX Pump, hydraulic; varies by model; contact factory

21 1 DPS-40-N06 Breather plug

22 1 01-031-005 Fitting, intake screen

23 1½ HO 150 Hydraulic fluid (gallons)

Table des matières

Autres manuels Vestil Système de levage

Vestil

Vestil A-LIFT-R Manuel utilisateur

Vestil

Vestil SCTAB-FP Manuel utilisateur

Vestil

Vestil HBD Series Manuel utilisateur

Vestil

Vestil LLH Series Manuel utilisateur

Vestil

Vestil HLD Series Manuel utilisateur

Vestil

Vestil D-FORK Series Manuel utilisateur

Vestil

Vestil BBL-4 Manuel utilisateur

Vestil

Vestil PRRJ-DOL Manuel utilisateur

Vestil

Vestil WP Series Manuel utilisateur

Vestil

Vestil FMDL Series Manuel utilisateur

Vestil

Vestil HDC-305-60 Manuel utilisateur

Vestil

Vestil SE/HP Series Manuel utilisateur

Vestil

Vestil OLA-2-42 Manuel utilisateur

Vestil

Vestil LLCB-202058 Manuel utilisateur

Vestil

Vestil WTJ-HITCH Manuel utilisateur

Vestil

Vestil PMPS Series Manuel utilisateur

Vestil

Vestil VAN-J Series Manuel utilisateur

Vestil

Vestil S-FORK-4/6-RL Manuel utilisateur

Vestil

Vestil HDC-305 Series Manuel utilisateur

Vestil

Vestil EPC Series Manuel utilisateur

Vestil

Vestil CTD-H-TP-3000 Manuel utilisateur

Vestil

Vestil AIR-1500-D Manuel utilisateur

Vestil

Vestil FM-0648 Manuel utilisateur

Vestil

Vestil DLH-CL2-1 Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur