Vertiv DCF 48U Instructions d'installation et d'entretien

DCF™ Optimized Rack System

Installer/User Guide

Technical Support Site

If you encounter any installation or operational issues with your product, check the pertinent section of

this manual to see if the issue can be resolved by following outlined procedures. For additional assistance,

visit https://www.VertivCo.com/en-us/support/

TABLE OF CONTENTS

1 Important Safety Instructions 5

2 Introduction 7

3 Major Components 9

3.1 Frame 9

3.1.1 Adjustable Rails 9

3.1.2 Full-height Rack PDU/Cable-management Bracket 9

3.1.3 Casters 9

3.2 Enclosure 9

3.2.1 Doors 10

3.2.2 Side Panels 10

3.2.3 Top Cover 11

3.3 Mounting Hardware and Tools 11

4 Installation 13

4.1 Inspection 13

4.2 Required Setup equipment 13

4.3 Unloading the DCF Rack 13

4.4 Equipment Layout, Repositioning, Removal and Installation 14

4.4.1 Installing the Edge Guard 14

4.4.2 Positioning and Attaching Front-andRear-Mount19-in.EIARails 15

4.4.3 Removing and Reversing Doors 17

4.4.4 Removing and Replacing Side Panels 18

4.5 Mounting Power Distribution Units 19

4.5.1 Installing a Full-height PDU/Cable-Management Bracket 19

4.6 Baying the DCF Cabinets 20

5 Periodic Maintenance 21

Vertiv | DCF Installer/User Guide | 3

Vertiv | DCF Installer/User Guide | 4

1 IMPORTANT SAFETY INSTRUCTIONS

Save These Instructions

This manual contains important instructions that must be closely followed during installation of this unit

to maintain compliance with agency listings. Read all safety and operating instructions. Adhere to all

warnings on the unit and in this manual. Follow all operating and user instructions.

WARNING: Risk of handling heavy unit. Can cause equipment damage, injury or death. Read all

instruction before beginning.

WARNING: Risk of top-heavy unit falling over. Improper handling can cause equipment damage, injury

or death. Only properly trained and qualified personnel wearing appropriate safety headgear, gloves,

shoes and glasses should attempt to move, lift, remove packaging from or prepare unit for installation.

Read all instructions before attempting to move, lift, remove packaging from or preparing unit for

installation.

This product is designed for commercial / industrial use only. This product is not intended for use with life

support or other U.S. FDA designated “critical” devices. Maximum loads must not exceed those specified in

this manual. The maximum load rating for the DCF is found in the DCF quide specficiation SL-11392. Do

not exceed the static load rating.

Install and operate in a clean environment, free from moisture, flammable liquids, gases and corrosive

substances. The DCF must be installed on a flat, level surface for proper assembly and operation.

Ensure that the DCF has proper ventilation. Never block or insert objects into the ventilation holes or

other openings. Maintain minimum clearances as specified in this manual.

Provide the minimum spacing between the accessories/components and the housing that shall be

maintained for safe operation of the equipment when installed in accordance with the National Electric

Code, ANSI/NFPA 70.As appropriate, all wiring and equipment should be installed in accordance with

NFPA 70, “National Electrical Code,” and the applicable sections of ANSI C2, “National Electrical Safety

Code."

We recommend that casters only be used to move empty cabinets.

Vertiv | DCF Installer/User Guide | 5

Vertiv | DCF Installer/User Guide | 6

This page intentionally left blank.

2 INTRODUCTION

The highly versatile DCF Optimized Rack System provides an organized, secure, controlled environment

in a single system for sensitive electronic equipment.

The DCF Optimized Rack System is available in two heights—42U and 48U (78.1in. and 88.6in; 1985mm

and 2251mm). These cabinet heights are available in the following widths and depths:

RACK

SIZE

DIMENSIONS, IN (MM)

HEIGHT WIDTH DEPTH

FRAME

ONLY

WITH LEVELING

FEET

WITH

CASTERS

WITH AND WITHOUT SIDE

PANELS

WITHOUT

DOORS

WITH

DOORS

42U 76.2 (1936.6) 77 (1956.2) 78.1 (1984.7) 23.6 (600) 41.8 (1062.5) 43.3 (1100)

48U 86.7 (2203.3) 87.5 (2222.9) 88.6 (2251.4) 31.5 (800) 45.8 (1162.5) 47.2 (1200)

Height, width, and depth dimensions are independent.

Depth with door is measured from the front door frame to the rear door frame.

Table 2.1 Rack dimensions

Assembly instructions in this manual cover the various configurations of the DCF Optimized Rack System,

either a single rack for simple equipment organization or a suite of DCF Optimized Rack System racks.

Vertiv | DCF Installer/User Guide | 7

Vertiv | DCF Installer/User Guide | 8

This page intentionally left blank.

3 MAJOR COMPONENTS

DCF Optimized Rack System will have all of the components addressed in this section. All components are

finished with a textured powder coat, color is RAL 7021.

3.1 Frame

The DCF Optimized Rack System is constructed of hot and cold rolled steel. Frame is light weight and

strong with a 3000 lb static load rating.

3.1.1 Adjustable Rails

The DCF Optimized Rack System ships with 2 sets of 19-in. (EIA310-E) compliant rails. The 19-in. rails have

U marking labels on both sides of the rails. Front and rear mount rails are installed in the DCF at 29.13in.

(740mm).

3.1.2 Full-height Rack PDU/Cable-management Bracket

Each DCF rack leaves the factory with 2 full-height rack pdu/cable-management brackets installed. The

brackets are installed in the rear of the rack, flush against the frame, one bracket installed on each side of

rack.

3.1.3 Casters

DCF Optimized Rack System ships standard with 4 swivel, non-locking casters installed.

Figure 3.1 Caster plate

3.2 Enclosure

Exterior components of the DCF Optimized Rack System are finished in textured powder coat, color RAL

7021.

Vertiv | DCF Installer/User Guide | 9

3.2.1 Doors

All doors for the DCF are framed from sheet metal and have hexagonal perforations leaving 75% open for

airflow and efficient cooling. All doors have a single-point latch system and come standard with lock. The

DCF rack ships with a single, contoured, perforated front door and split-perforated rear doors designed for

easy access. All doors can easily be removed and the single, contoured front door is designed for

reversibility (left/right) hinging in the field. (See "Removing and Reversing Doors" on page17.)

Each door opens to 135 degrees.

FRAME SIZE

DOOR DIMENSIONS, IN (MM)

PART NUMBER

HEIGHT WIDTH

42U

78.1 x 23.6 (2000 x 600)

76 (1931.5)

23 (586) Part#546053G1L

78.1 x 31.5 (2000 x 800) 31 (768) Part#546053G2L

48U

83.4 x 23.6 (2100 x 600)

87 (2198.2)

23 (586) Part#546053G3L

83.4 x 31.5 (2100 x 800) 31 (768) Part#546053G4L

Table 3.1 Door dimensions, single door

FRAME SIZE

DOOR DIMENSIONS, IN (MM)

PART NUMBER

HEIGHT WIDTH EACH DOOR

42U

78.1 x 23.6 (2000 x 600)

76 (1931.5)

11.5 (293) Part#546054G1L

78.1 x 31.5 (2000 x 800) 15.5 (384) Part#546054G2L

48U

83.4 x 23.6 (2100 x 600)

87 (2198.2)

11.5 (293) Part#546054G3L

83.4 x 31.5 (2100 x 800) 15.5 (384) Part#546054G4L

Table 3.2 Door dimensions, split doors

3.2.2 Side Panels

Side panels for the DCF Optimized Rack System are a split side panel design constructed of sheet metal.

Each side panel section comes with a lock for security which is installed in the center top of each panel.

Two keys ship with the side panels; the side panel keys are the same keys that are used for the doors.

RACK HEIGHT, IN (MM) RACK DEPTH, IN (MM) SIDE PANEL PART NUMBERS

78.1 (2000)

43.3 (1100) 546055G1L

47.2 (1200) 546055G2L

88.6 (2250)

43.3 (1100) 546055G3L

47.3 (1200) 546055G4L

Table 3.3 Side-panel sizes and part numbers

Vertiv | DCF Installer/User Guide | 10

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Vertiv Support et étagère

Vertiv

Vertiv RMPSU Manuel utilisateur

Vertiv

Vertiv NetSure 48BA1200-19 Manuel utilisateur

Vertiv

Vertiv VP8641 Manuel utilisateur

Vertiv

Vertiv Knurr DCM Manuel utilisateur

Vertiv

Vertiv KMMLED156 Instructions d'installation et d'entretien

Vertiv

Vertiv NetSure 48BA1200-23 Manuel utilisateur

Vertiv

Vertiv KMMLED156 Manuel utilisateur

Vertiv

Vertiv Knurr DCM Manuel utilisateur

Vertiv

Vertiv Avocent Manuel utilisateur

Vertiv

Vertiv Knurr PowerTrans2 Manuel utilisateur

Vertiv

Vertiv Knurr Miracel 2 Manuel utilisateur

Vertiv

Vertiv MPE Manuel utilisateur

Vertiv

Vertiv MPH2 Manuel utilisateur

Vertiv

Vertiv DCE E42611 Manuel utilisateur

Vertiv

Vertiv 24BA1200-23 Manuel utilisateur

Vertiv

Vertiv SmartAisle 03.029.214 Series Manuel utilisateur

Vertiv

Vertiv eSure 60017372 Manuel utilisateur

Vertiv

Vertiv VE Series Manuel utilisateur

Vertiv

Vertiv SmartAisle-SwitchTube 19 Core 320mm 7-12HE/U Manuel utilisateur

Vertiv

Vertiv Knurr DCM Heavy Duty Rack Manuel utilisateur

Vertiv

Vertiv Smaract Manuel utilisateur

Vertiv

Vertiv MPX PRC Manuel utilisateur

Vertiv

Vertiv SmartAisle 12-21HE/U Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur