Verkada AC62 Manuel utilisateur
Document
Document Details
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
V1.0 (20220620)
(V1.0 first published 20220620)
Firmware
Firmware version can be verified on
Verkada Command command.verkada.com.
2
Appendix
AC62 Compliance
FCC
Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in this manual.
The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user
body or set the device to lower output power if such function is available.
IC
Statement
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage
reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for
an uncontrolled environment and are safe for intended operation as described in this manual.
The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user
body or set the device to lower output power if such function is available.
Déclaration d'exposition aux radiations: Le produit est conforme aux limites d'exposition pour les appareils
portables RF pour les Etats-Unis et le Canada établies pour un environnement non contrôlé.
Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel.
La réduction aux expositions RF peut être augmentée si l'appareil peut être conservé aussi loin que possible du
corps de l'utilisateur ou que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction
est disponible.
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
3
Introduction
What’s in the box
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
4
What you’ll need
●A working internet connection
●A smartphone or laptop
●A #2 phillips head and power drill
●A level
Please note Two (2) person installation
recommended
Connect
Connect the AC62 to your network using the
Ethernet port located at the bottom of the
controller. Connect the AC62 power supply
into your power outlet.
Supports 110VAC to 240VAC (50-60Hz).
After connecting the AC62 to network and
power, visit: verkada.com/start
For detailed installation instructions, visit:
verkada.com/support
AC62 Door Controller Wall Mount GuideWall Mount
AC Cable 6x Plywood Screws 2x Keys
●AC62 Door Controller
●Wall Mount
●Wall Mount Guide
●AC Cable
●6x Plywood Screws
●2x Keys
Introduction
Overview 1/2
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
5
Lock
Status LED
LED Behavior
Solid Orange - Controller is on and booting up
Flashing Orange - Controller is updating firmware
Flashing Blue - Controller is managing doors, but cannot reach the server
Solid Blue - Controller is managing doors and connected to the server
Flashing Pink - Identify
AC inlet
Power supply
ACU diagram
Introduction
Overview 2/2
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
6
Panel highlights
1 Ports for: Doors 1 to 16. All door ports function the same.
2 Ports for: AUX, Fire Alarm Interface(FAI)
3 Ports for: AC, Ethernet, USB, UPS, Door Tamper
Status LED
AC Ethernet
1
2
3
Installation
Unboxing
Use the pull handle to lift and remove
AC62 from the box.
Please note Two (2) person installation
recommended
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
7
Lay AC62 on a flat surface, open the
door and remove the cardboard.
Keep cardboard intact for next step.
Installation
Mounting 1/4
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
8
Use cardboard piece with the mounting
template, kept from the previous step, to
get a sense of the space AC62 will occupy
on the wall.
Use mounting template to drill pilot holes for
the mount plate.
Use the supplied screws to install the mount
plate onto the wall. Ensure that the Verkada
V is pointing towards the floor.
The enclosure will extend down roughly 31”
(~79cm), from the top of the mount plate.
Please Note that the supplied screws are intended for
plywood installations. For other wall materials, ensure
proper load-bearing fasteners are used
The size of the enclosure is:
31 x 20” (79 x 51 cm)
Carefully slot the enclosure onto
the mount plate.
Use the supplied screws to
secure the enclosure onto the
wall according to thru holes.
Installation
Mounting 3/4
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
10
Autres manuels pour AC62
1
Table des matières
Autres manuels Verkada Système d'ouverture de porte
