Vents VUE 100 P3 Manuel utilisateur

USER’S MANUAL

VUE 100 P3

VUE 200 P3

VUE 300 P3

VUE 450 P3

Heat and energy recovery air handling unit

VUE P3 A3/A4

www.ventilation-system.com

This user’s manual is a main operating document intended for technical, maintenance, and operating staﬀ.

The manual contains information about purpose, technical details, operating principle, design, and installation of the VUE P3 A3/A4 unit

and all its modiﬁcations.

Technical and maintenance staﬀ must have theoretical and practical training in the ﬁeld of ventilation systems and should be able to

work in accordance with workplace safety rules as well as construction norms and standards applicable in the territory of the country.

Safety requirements..................................................................................................................................................................... 2

Purpose................................................................................................................................................................................................ 4

Delivery set........................................................................................................................................................................................ 4

Designation key.............................................................................................................................................................................. 4

Technical data.................................................................................................................................................................................. 5

Design and operating principle ........................................................................................................................................... 7

Mounting and set-up.................................................................................................................................................................. 9

Connection to power mains .................................................................................................................................................. 10

Technical maintenance.............................................................................................................................................................. 11

Troubleshooting............................................................................................................................................................................. 12

Storage and transportation regulations.......................................................................................................................... 12

Certiﬁcate of acceptance.......................................................................................................................................................... 14

Seller information.......................................................................................................................................................................... 14

Installation certiﬁcate.................................................................................................................................................................. 14

Warranty card................................................................................................................................................................................... 14

CONTENTS

www.ventilation-system.com

SAFETY REQUIREMENTS

All user’s manual requirements as well as the provisions of all the applicable local and national

construction, electrical, and technical norms and standards must be observed when installing

and operating the unit.

Disconnect the unit from the power supply prior to any connection, servicing, maintenance, and

repair operations.

Only qualied electricians with a work permit for electrical units up to 1000 V are

allowed for installation. The present user’s manual should be carefully read before

beginning works.

Check the unit for any visible damage of the impeller, the casing, and the grille before starting

installation. The casing internals must be free of any foreign objects that can damage the

impeller blades.

While mounting the unit, avoid compression of the casing! Deformation of the casing may result

in motor jam and excessive noise.

Misuse of the unit and any unauthorised modiﬁcations are not allowed.

Do not expose the unit to adverse atmospheric agents (rain, sun, etc.).

Transported air must not contain any dust or other solid impurities, sticky substances, or ﬁbrous

materials.

Do not use the unit in a hazardous or explosive environment containing spirits, gasoline,

insecticides, etc.

Do not close or block the intake or extract vents in order to ensure the eﬃcient air ﬂow.

Do not sit on the unit and do not put objects on it.

The information in this user’s manual was correct at the time of the document’s preparation.

The Company reserves the right to modify the technical characteristics, design, or conﬁguration

of its products at any time in order to incorporate the latest technological developments.

VUE P3 A3/A4

www.ventilation-system.com

THE PRODUCT MUST BE DISPOSED SEPARATELY AT THE END OF ITS SERVICE LIFE.

DO NOT DISPOSE THE UNIT AS UNSORTED DOMESTIC WASTE.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or

similarly qualiﬁed persons in order to avoid a safety hazard.

This unit is not intended for use by persons (including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the unit by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the unit.

Ensure that the unit is switched oﬀ from the supply mains before removing the guard.

Precautions must be taken to avoid the back-ﬂow of gases into the room from the open ﬂue of

gas or other fuel-burning appliances.

www.ventilation-system.com

THE UNIT SHOULD NOT BE OPERATED BY CHILDREN OR PERSONS WITH REDUCED

PHYSICAL, MENTAL, OR SENSORY CAPACITIES, OR THOSE WITHOUT THE APPROPRIATE

TRAINING.

THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY PROPERLY QUALIFIED

PERSONNEL AFTER THE APPROPRIATE BRIEFING.

THE CHOICE OF UNIT INSTALLATION LOCATION MUST PREVENT UNAUTHORISED

ACCESS BY UNATTENDED CHILDREN.

DELIVERY SET

DESIGNATION KEY

NAME NUMBER

Air handling unit 1 pc.

User’s manual 1 pc.

Controller 1 pc.

Packing box 1 pc.

VUE 100 P 3 L A4

Controller

A3: P3-1-300 speed controller

A4: SP3-1 sensor control panel

Modication

L: left-handed

R: right-handed

Casing type

Low-proﬁle unit

Mounting features

Suspended, horizontal spigot orientation

Rated air ow [m3/h]

100/200/300/450

Series

VUE: energy recovery air handling unit

The unit is designed to ensure continuous mechanical air exchange in houses, oﬃces, hotels, cafes, conference halls, and other utility

and public spaces as well as to recover the heat energy contained in the air extracted from the premises to warm up the ﬁltered stream

of intake air.

The unit is not intended for organizing ventilation in swimming pools, saunas, greenhouses, summer gardens, and other spaces with

high humidity.

Due to the ability to save heating energy by means of energy recovery, the unit is an important element of energy-eﬃcient premises.

The unit is a component part and is not designed for stand-alone operation. It is rated for continuous operation.

Transported air must not contain any ﬂammable or explosive mixtures, evaporation of chemicals, sticky substances, ﬁbrous materials,

coarse dust, soot and oil particles or environments favourable for the formation of hazardous substances (toxic substances, dust,

pathogenic germs).

PURPOSE

VUE P3 A3/A4

www.ventilation-system.com

TECHNICAL DATA

The unit is designed for indoor application with the ambient temperature ranging from +1 °C up to +40 °C and relative humidity up to

60 % without condensation. In cold, damp rooms, there is a possibility of freezing or condensation inside and outside the casing.

In order to prevent condensation on the internal walls of the unit, it is necessary that the surface temperature of the casing is 2-3 °C above

the dew point temperature of the transported air.

The unit should be operated continuously, and in cases where ventilation is not necessary, reduce the air ﬂow of the fans to a minimum

(20%). This will ensure a favorable indoor climate and reduce the amount of condensation inside the unit, which can damage electronic

components. Never use the unit for dehumidiﬁcation, for example, of new buildings.

The unit is rated as a Class I electrical appliance.

Hazardous parts access and water ingress protection rating:

IP22 for the unit connected to the air ducts

IP44 for the unit motors

The unit design is constantly being improved, thus some models may be slightly diﬀerent from those described in this manual.

Parameter VUE 100 P3 VUE 200 P3 VUE 300 P3 VUE 450 P3

Unit supply voltage, 50 Hz [V] 1~ 230

Maximum unit power [W] 76 141 193 354

Maximum unit current [A] 0.33 0.63 0.84 1.54

Maximum ﬂow rate [m3/h] 160 280 340 500

RPM [min-1]2750 2840 2720 2870

Sound pressure level at 3 m distance [dBA] 47 49 52 57

Transported air temperature [°С] -15...+40

Casing material Painted steel

Insulation Foamed rubber, 5 and 10 mm

Extract ﬁlter G4

Supply ﬁlters G4 + F8 (PM2.5 93 %)

Connected air duct diameter [mm] 100 100 150 150

Heat recovery eﬃciency [%] 75-7 72-87 66-87 71-87

Humidity recovery eﬃciency [%] 32-47 27-47 22-47 23-40

Heat exchanger type Cross-flow enthalpy

Weight [kg] 17 24 27 39

SEC class D D E E

www.ventilation-system.com

ØD

A B

Model Dimensions [mm]

Ø D A A1 B B1 H H1 L

VUE 100 P3 100 734 600 481 571 204 223 300

VUE 200 P3 100 987 854 704 793 222 241 480

VUE 300 P3 150 987 854 704 793 227 246 480

VUE 450 P3 150 1157 1024 754 843 277 296 488

VUE P3 A3/A4

www.ventilation-system.com

DESIGN AND OPERATING PRINCIPLE

Supply fan

Extract fan

Extract air lter

Control unit

Thermostat for heat exchanger freeze protection

Cable glands

Cross-ow heat exchanger

Supply air lter

Controller

Power cord with a plug

Inspection hatch for lter and heat

exchanger maintenance

Left-handed modication

The service side of the unit is equipped with a detachable inspection hatch on manual bolts for ﬁlter and heat exchanger cleaning and

replacement operations. The plate enthalpy cross-ﬂow heat exchanger is made of polymerized cellulose.

The control unit is positioned inside the unit casing . The power cable and grounding cables are connected to the control unit via the

cable gland located at the side of the unit. The unit is equipped with a controller and a power cord with a Euro Plug XP.

Warm stale extract air from the room ﬂows into the unit, where it is ﬁltered by the extract ﬁlter, then air ﬂows through the heat

exchanger and is exhausted outside by the extract fan. Cold fresh air from the outside ﬂows into the unit, where it is cleaned by the

supply ﬁlter. Then the air ﬂows through the heat exchanger and is directed to the room with the supply fan.

Supply air is heated in the heat exchanger by transferring the heat energy of warm and humid extract air to the cold fresh air.

The air ﬂows are fully separated while ﬂowing through the heat exchanger. Heat recovery minimizes heat losses, which reduces the

cost of space heating in the cold season. The enthalpy heat exchanger provides both heat and humidity recovery.

In warm seasons the heat exchanger operates to cool down and dehumidify the supply air. In cold seasons the heat exchanger

operates to warm up supply air and humidify it. Water vapour from the humid extract air is condensed and absorbed by the heat

exchanger plates. The recovered humidity and heat are transferred to the supply air ﬂow. The air streams are fully separated within the

heat exchanger and the microbes and smells are isolated.

LEFT-HANDED AND RIGHT-HANDED MODIFICATIONS

The ﬁgure below shows the arrangement of spigots for left- and right-handed modiﬁcations. Choosing the right arrangement can

improve the ease of installation, shorten the length of the ducts and reduce the number of air duct bends (elbows)

EXTRACT AIR

SUPPLY AIR

INTAKE AIR

EXHAUST AIR

INTAKE AIR

SUPPLY AIR

EXHAUST AIR

EXTRACT AIR

Left-handed modiﬁcation Right-handed modiﬁcation

www.ventilation-system.com

The provide heat exchanger freeze protection during the cold season, the unit is equipped with a thermostat that is installed in the

exhaust air duct downstream of the heat exchanger. The Defrosting mode is activated when the exhaust air temperature is +3 ˚С.

After temperature increase the unit returns to the previous operation mode.

In the Defrosting mode the supply fan is turned oﬀ and the heat exchanger is warmed up with warm extract air ﬂow.

To set the thermostat threshold value, turn the control knob to the desired position.

The recommended thermostat operating temperature is +3 °C (factory setting).

EXTRACT AIR

SUPPLY AIR

INTAKE AIR

EXHAUST AIR

INTAKE AIR

SUPPLY AIR

EXHAUST AIR

EXTRACT AIR

Left-handed modiﬁcation Right-handed modiﬁcation

VUE P3 A3/A4

www.ventilation-system.com

MOUNTING AND SETUP

READ THE USER'S MANUAL BEFORE INSTALLING THE UNIT.

WHILE INSTALLING THE UNIT ENSURE CONVENIENT ACCESS FOR SUBSEQUENT

MAINTENANCE AND REPAIR.

The unit is designed for suspended ceiling mounting with anchor threaded rods, nuts and anti-vibration rubber.

Fasteners for fan mounting are not included in the delivery set and should be ordered separately.

While choosing fasteners consider the material of the mounting surface as well as the weigh of the unit, refer to the Technical data

section. Fasteners for unit mounting should be selected by a qualiﬁed specialist! Before mounting make sure the casing does not

contain any foreign objects (e.g. foil, paper).

The minimum distance between the unit and the ceiling should be at least 20 mm.

To attain the best performance of the unit and to minimise turbulence-induced air pressure losses, connect the straight air duct section

to the spigots on both sides of the unit while mounting.

Minimum straight air duct length:

• equal to 1 air duct diameter on the intake side

• equal to 3 air duct diameters on outlet side

If the air ducts are too short or not connected, protect the unit parts from ingress of foreign objects.

To prevent uncontrollable access to the fan, the spigots may be covered with a protecting grille or other protecting device with mesh

width not more than 12.5 mm.

Washer

Nut

Threaded rod

Vibration absorbing rubber

min 20 mm

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Vents Unité de traitement de l'air

Vents

Vents VUT 350 EH Manuel utilisateur

Vents

Vents VUT R 400 EH EC A17 Manuel utilisateur

Vents

Vents VUT 350 PE EC Manuel utilisateur

Vents

Vents Freshbox 200 ERV WiFi Manuel utilisateur

Vents

Vents VUE P3 A1 Manuel utilisateur

Vents

Vents DVUT 1000 PB EC Manuel utilisateur

Vents

Vents VUT 800 WH Manuel utilisateur

Vents

Vents DuoVent 150 EC Manuel utilisateur

Vents

Vents VUT 2000 PBE EC Manuel utilisateur

Vents

Vents Micra 110 Manuel utilisateur

Vents

Vents VUT2 250 P EC Manuel utilisateur

Vents

Vents Micra 200 ERV WiFi Manuel utilisateur

Vents

Vents Micra 150 E Manuel utilisateur

Vents

Vents VUE 100 P3B EC Manuel utilisateur

Vents

Vents DVUT 300 PB EC Manuel utilisateur

Vents

Vents VUT 2000 PBW EC Manuel utilisateur

Vents

Vents VUTR 400 V EC Manuel utilisateur

Vents

Vents DVUT 500 HB Manuel utilisateur

Vents

Vents VUT 350 H Manuel utilisateur

Vents

Vents DVUT 300 PB EC Manuel utilisateur

Vents

Vents VUT 350 PE EC Manuel utilisateur

Vents

Vents VUT 160 V EC Manuel utilisateur

Vents

Vents VUT 230 V5 Manuel utilisateur

Vents

Vents VUT 160 V EC Manuel utilisateur

Manuels Unité de traitement de l'air populaires d'autres marques

Klimor

Klimor EVO-S Manuel utilisateur

Salda

Salda SMARTY XP Mode d’emploi

BLAUBERG

BLAUBERG KOMFORT Roto EC S400 Manuel utilisateur

Trenton

Trenton TPLP Series Manuel utilisateur

Kemper

Kemper CleanAirTower Manuel utilisateur

Daikin

Daikin DV PTC 14 Series Manuel utilisateur

Haier

Haier HB2400VA1M20 Manuel utilisateur

Webasto

Webasto BlueCool A-Series Manuel utilisateur

RDZ

RDZ DA 701 Document technique

Carrier

Carrier 39T Dimensions et guide d'installation

Armstrong Air

Armstrong Air BCE5V Series Manuel utilisateur

ActronAir

ActronAir CAY500T Manuel utilisateur

Carrier

Carrier 40MBDAQ Manuel utilisateur

Allied

Allied A93UH1E Manuel utilisateur

Nortek

Nortek B6VMAI Manuel utilisateur

TemperZone

TemperZone Econex Pro OPA 1410RLTM4FPQD Guide de maintenance et de service

RDZ

RDZ WHR 200 Document technique

AAON

AAON H3 Series Manuel du propriétaire