VentAHood V-Line K250 Manuel utilisateur

V-Line Blower

How to Clean

For models starting with K250.

Step 1. Release the blower pan.

Be sure the motor is turned off before proceeding. The blower pan is easily removed for

cleaning by unsnapping the suitcase latches (one on each side of the blower assembly).

Step 2. Remove the blower pan.

With the blower pan latches released, remove the blower pan by pulling the pan downward.

Be careful to keep the tray level if the hood has been recently used.

Step 3. Release the blower wheel.

The blower wheel can be removed by using a 1/8” hex wrench. There is a small set screw

on the side of the hub in the base of the wheel that tightens up against a “at” spot on the

motor shaft. There is also a small hole in one of the blades of the blower wheel that aligns

with the set screw. Insert the wrench through the hole in the fan blade and into the set

screw. The set screw must be turned 1/2 turn counterclockwise to free the blower wheel

from the motor shaft. If the hood is more than ve years old and the set screw has never

been loosened, it may be difcult or even impossible to remove the blower wheel. A liquid

penetrating oil may help you loosen the set screw, but it might prove more practical to clean

the wheel without removing it from the motor shaft.

Step 4. Remove the blower wheel.

Once the set screw is loosened, pull the blower wheel downward slightly, then gently remove

the blower wheel from shaft. Use caution to avoid bending or distorting the blower wheel

and take care not to move or lose the metal balancing clips that may be afxed to the blower

wheel. If the blower wheel is difcult to remove, the area where the motor shaft makes

contact with the blower wheel hub may need to be sprayed with a common penetrating oil

such as WD-40®and allowed to soak for a short time.

Step 5. Clean the parts and reassemble.

The inside of the blower assembly that remains inside the hood can be

cleaned with a soft cloth and warm soapy water (liquid dish detergent).

Do not use acids, abrasives, strong detergents, solvents, or scouring

pads. When cleaning interior blower surfaces, be careful to avoid any

metal edges.

Clean the blower pan in a sink of warm soapy water (liquid dish detergent)

and let soak for a few minutes. Wash with a sponge or dishcloth, rinse,

and let drain.

A soft bristle toothbrush with warm soapy water may be used to clean

the blades on the blower wheel. Alternatively, the blower wheel may be

soaked in warm soapy water.

Reassemble in the opposite order of disassembly. When reinstalling

the blower wheel onto the motor shaft, make sure the set screw makes

direct contact with the “at spot” on the motor shaft. Slide the blower

wheel onto the motor shaft as far as it will go, making sure the top of

the blower wheel does not touch the upper scroll area.

If the blower wheel is too far up, it will rub against the upper scroll area,

and if it is too far down, it will rub the inside of the blower pan. Adjust

the blower wheel slightly to nd the correct top-to-bottom location.

Tighten the set screw (clockwise) to lock the blower wheel in the correct

position.

Once it’s had time to completely dry, reinstall the blower pan and snap

it in place via the suitcase latches (one on each side of the blower

assembly).

Rev. 0520

1000 N Greenville Ave

Richardson, TX 75081

800-331-2492

www.ventahood.com

Table des matières

Autres manuels VentAHood hotte de ventilation

VentAHood

VentAHood Magic Lung Blower Manuel d'utilisation

VentAHood

VentAHood VP526 Manuel utilisateur

VentAHood

VentAHood AH12 Manuel utilisateur

VentAHood

VentAHood JPH DESIGNER SERIES Manuel utilisateur

VentAHood

VentAHood B100 Single Manuel utilisateur

VentAHood

VentAHood Ventilation Hood Models Equipped with K250... Manuel utilisateur

VentAHood

VentAHood RM1000 Manuel d'utilisation

VentAHood

VentAHood JCH/A1 DESIGNER SERIES Manuel utilisateur

VentAHood

VentAHood WALL MOUNT HOOD Manuel utilisateur

VentAHood

VentAHood UNDER CABINET HOOD Manuel utilisateur

VentAHood

VentAHood K Series Manuel utilisateur

VentAHood

VentAHood JCIH/C1 Manuel utilisateur

VentAHood

VentAHood ISLAND RANGE Manuel utilisateur

VentAHood

VentAHood EPTH18 Manuel utilisateur

VentAHood

VentAHood Euroline Manuel utilisateur

VentAHood

VentAHood ISLAND Manuel utilisateur

VentAHood

VentAHood CILH9 ISLAND RANGE HOOD Manuel utilisateur

VentAHood

VentAHood B100 Single 300 CFM Manuel utilisateur

VentAHood

VentAHood Retro Style Under Cabinet Rangehood CLH9 Manuel utilisateur

VentAHood

VentAHood JCH/B1 Series Manuel utilisateur

VentAHood

VentAHood ZTH Manuel utilisateur

VentAHood

VentAHood K-SERIES Manuel utilisateur

VentAHood

VentAHood M600 Manuel utilisateur

VentAHood

VentAHood EUROLINE Manuel utilisateur

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur