Velleman K8084 Manuel utilisateur

VOLUME AND TONE CONTROL - PREAMPLIFIER

K8084

ILLUSTRATED ASSEMBLY MANUAL H8084IP-1

Total solder points: 162

Difficulty level: beginner 1 2 3 4 5 advanced

Whenusingoneofouramplifiers(bigorsmall),youalways

needavolumecontrolandpreferablyalsoatonecontrol

Features & specifications

When using one of our amplifiers (big or small), you always need a volume control and preferably also a tone

control. This kit comes complete with all input / output connections and potentiometers.

Furthermore it is possible to amplify or attenuate the input signal.

FEATURES:

 stereo volume control

 stereo Baxandall bass and treble control

 bass and treble potentiometers with centre click

 customizable attenuation or amplification

 complete with knobs

SPECIFICATIONS:

 supply voltage: 2 x 12VAC / 100mA

 frequency response: 3Hz - 500kHz (-3dB)

 standard amplification: x1

 signal to noise ratio: 98dB

 harmonic distortion: < 0.005% (@1KHz)

 maximum output: 5V RMS

 tone control:

+ and -15dB @ 20Hz

+ and -15dB @ 15kHz

 Input impedance: 50k ohms

 PCB dimensions: 105 x 70mm / 4,1 x 2,75"

modifications reserved

Assembly hints

1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a small tip.

• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’and will

protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.

• Thin raisin-core solder. Do not use any flux or grease.

• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they

cannot fly towards the eyes.

• Needle nose pliers, for bending leads, or to hold components in place.

• Small blade and Phillips screwdrivers. A basic range is fine.

For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

⇒ Make sure the skill level matches your experience, to avoid disappointments.

⇒ Follow the instructions carefully. Read and understand the entire step before you perform each operation.

⇒ Perform the assembly in the correct order as stated in this manual

⇒ Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.

⇒ Values on the circuit diagram are subject to changes.

⇒ Values in this assembly guide are correct*

⇒ Use the check-boxes to mark your progress.

⇒ Please read the included information on safety and customer service

* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’on a separate leaflet.

Assembly hints

1.3 Soldering Hints :

1- Mount the component against the PCB surface and carefully solder the leads

2- Make sure the solder joints are cone-shaped and shiny

3- Trim excess leads as close as possible to the solder joint

REMOVE THEM FROM THE TAPE ONE AT A TIME !

AXIAL COMPONENTS ARE TAPED IN THE

CORRECT MOUNTING SEQUENCE !

 R1 : 1K (1 - 0 - 2 - B)

 R2 : 100K (1 - 0 - 4 - B)

 R16 : 10K (1 - 0 - 3 - B)

 R17 : 10K (1 - 0 - 3 - B)

 R18 : 10K (1 - 0 - 3 - B)

 R19 : 10K (1 - 0 - 3 - B)

 R20 : 10K (1 - 0 - 3 - B)

Hint for R21 to R24

Modify the resistances marked RF

and RA to increase the input sen-

sitivity (more amplification).

The formula is:

amplification = (RF/RA) + 1

E.g. to double the amplification because

the input of the connecting device is too

weak, mount 100K for RF (R22 and

R23).

 R21 : 100K (1 - 0 - 4 - B)

 R22 : 1K (1 - 0 - 2 - B)

 R23 : 1K (1 - 0 - 2 - B)

 R24 : 100K (1 - 0 - 4 - B)

3. Resistors

R...

Construction

 D1 : 1N4007

 D2 : 1N4007

 D3 : 1N4007

 D4 : 1N4007

2. Diodes. Watch the polarity !

D...

CATHODE

 ZD1 : 9V1

 ZD2 : 9V1

1. Zenerdiodes. Watch the

polarity !

CATHODE

ZD...

Hint for R2 and R4:

To weaken the input (divide)

E.g. to connect the input with an ampli-

fier output.

Choose an inferior value for R2 and

R4.

The dividing factor = (R1/R2) + 1

E.g. a value of 100Ωfor RD (R2 and R4)

will divide the input by 11.

 R3 : 1K (1 - 0 - 2 - B)

 R4 : 100K (1 - 0 - 4 - B)

 R5 : 10 (1 - 0 - 0 - B)

 R6 : 10 (1 - 0 - 0 - B)

 R7 : 1K (1 - 0 - 2 - B)

 R8 : 1K (1 - 0 - 2 - B)

 R9 : 3K3 (3 - 3 - 2 - B)

 R10 : 1K (1 - 0 - 2 - B)

 R11 : 1K (1 - 0 - 2 - B)

 R12 : 10 (1 - 0 - 0 - B)

 R13 : 3K3 (3 - 3 - 2 - B)

 R14 : 3K3 (3 - 3 - 2 - B)

 R15 : 10K (1 - 0 - 3 - B)

 C19 : 47µ F

 C20 : 47µ F

 C21 : 220µ F

 C22 : 220µ F

 IC1 : 8p

 IC2 : 8p

4. IC sockets, Watch the

position of the notch!

 LD1 : 5mm Red "Power"

6. LED. Watch the polarity !

COLOR= 2...5

LD...

CATHODE

Construction

 T1 : BC547

 T2 : BC557

7. Transistors

 C1 : 15pF (15)

 C2 : 15pF (15)

 C3 : 100pF (101)

 C4 : 100pF (101)



C5 : 4,7nF (472)



C6 : 4,7nF (472)



C7 : 4,7nF (472)



C8 : 4,7nF (472)



C9 : 47nF (473)



C10 : 47nF (473)

5. Capacitors.

c... C...

 SK1 : 3p AC input

8. Terminal block

 C11 : 47nF (473)

 C12 : 47nF (473)



C13 : 47nF (473)



C14 : 47nF (473)



C15 : 47nF (473)

 C16 : 47nF (473)

 C17 : 1µ F / 63V

 C18 : 1µ F / 63V

9. Electrolytic capacitors

C...

Connect a 2 x 12V / min. 100mA transformer with power connector

SK1 (e.g. our 212007C). This is a 2 x 12V 3-wire transformer, 1 wire is

the common 0 and generally of another colour.

A transformer without connecting wires will be marked 12 – 0 – 12.

 SK2 : input

 SK3 : output

10. Dual RCA Jacks

 RV1 : A 50K (Volume)

 RV2 : B 50K (Bass)

 RV3 : B 50K (Treble)

11. Potentiometers

RV1

12. Test

100mA

12V

Construction

Connect the mains voltage to the transformer; mount a 100mAT security fuse in series with the transformer.

Use a high-quality power cord and plug for the connection to the mains.

When the transformer is live, the LED will light.

 Disconnect from mains.

 Mount the ICs into the socket (mind the position of the notch)

 Reconnect the mains.

 Check if the LED lights.

 Connect a device with the input e.g. MP3 player, CD player.

 Connect the output with a power amplifier.

 Turn down the volume to its minimum.

 Switch on the power amplifier.

 Hint: you can also connect headphones instead of a power amplifier. You can use connections GND-TPR-

TPL; GND is the ground.

Test

13. Building into a enclosure

Enclosure

To avoid hum, it is recommended to mount the K8084 and the transformer into a Metal housing.

Drill the holes for the connections and the potentiometers.

 Hint:You can drill the holes for the knobs or the potentiometers and mount the knob afterwards.

1 hole in the print (next to RV3) is provided to connect the earthing to the housing through the metal spacers

or bolts.

Hint:

 Mount the transformer as far away as possible from the circuit to avoid humming.

 It is recommended to leave this circuit under voltage; disconnect the voltage only when not in use for a

long time. Always switch off the power amplifier first before switching off the preamplifier.

14. PCB

PCB

Table des matières

Autres manuels Velleman Amplificateur

Velleman

Velleman K1803 Manuel utilisateur

Velleman

Velleman K4040B Manuel utilisateur

Velleman

Velleman HQ Power PAA01 Manuel utilisateur

Velleman

Velleman HQ Power PA100U Manuel utilisateur

Velleman

Velleman K4040 Manuel utilisateur

Velleman

Velleman HQ Power VPA2350MB Manuel utilisateur

Velleman

Velleman 8040 Manuel utilisateur

Velleman

Velleman HQ Power VPA2100U1 Manuel utilisateur

Velleman

Velleman HQ Power PAA04 Manuel utilisateur

Velleman

Velleman VD4C Manuel utilisateur

Velleman

Velleman K4003 Manuel utilisateur

Velleman

Velleman HQ Power PA100U Manuel utilisateur

Velleman

Velleman HQ Power ONELINER 100 Manuel utilisateur

Velleman

Velleman HQ-Power ANTM7 Manuel utilisateur

Velleman

Velleman VM100 Manuel utilisateur

Velleman

Velleman K8066 Manuel utilisateur

Velleman

Velleman HQ Power VPA2200MBN Manuel utilisateur

Velleman

Velleman 8021 Manuel utilisateur

Velleman

Velleman K4001 Manuel utilisateur

Velleman

Velleman K4003 Manuel utilisateur

Velleman

Velleman K4005B Manuel utilisateur

Velleman

Velleman K4020 Manuel utilisateur

Velleman

Velleman K8040 Manuel utilisateur

Velleman

Velleman High-Q Velleman-kit K8022 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur