Velleman K6001 Manuel utilisateur

TEMPERATURE SENSOR

K6001

ILLUSTRATED ASSEMBLY MANUAL H6001IP-2

Total solder points: 71

Difficulty level: beginner 12345 advanced

ForusewithourK6000or

K6002kits.

This kit has been developed especially to be combined with our K6000 or K6002 in order to create a tem-

perature regulating and temperature control system. Combined with the K6000 kit, a completely programma-

ble thermostat can be assembled. The use of a separate sensor offers the advantage of making the distance

between the controller and the sensor irrelevant.

Specifications:

 Temperature range of the transmitter : -40°C to 150°C.

 Pulse width modulation : 200µs / °C.

 Generated pulse width :

- at –40°C : 2ms (+/- 500µs adjustable)

- at 150°C : 40ms (+/- 2500µs adjustable)

 Linearity from –10°C to 50°C : better than 0,5%.

 Full scale : better than 2%.

 Tested up to 50m (distance between sensor and controller)

 Output : 15mA current loop

 Supply voltage : 12VDC (+/- 2V) / 20mA Max.

 PCB dimensions: 45 x 47mm (1.8" x 1.9")

Features & Specifications

Assembly hints

1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a small tip.

• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will

protectthe tip, and enables youto makegoodconnections. Whensolder rollsoff the tip,it needs cleaning.

• Thin raisin-core solder. Do not use any flux or grease.

• A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they

cannot fly towards the eyes.

• Needle nose pliers, for bending leads, or to hold components in place.

• Small blade and Phillips screwdrivers. A basic range is fine.

For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

⇒ Make sure the skill level matches your experience, to avoid disappointments.

⇒ Follow the instructions carefully. Read and understand the entire step before you perform each operation.

⇒ Perform the assembly in the correct order as stated in this manual

⇒ Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.

⇒ Values on the circuit diagram are subject to changes.

⇒ Values in this assembly guide are correct*

⇒ Use the check-boxes to mark your progress.

⇒ Please read the included information on safety and customer service

* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.

Assembly hints

1.3 Soldering Hints :

1- Mount the component against the PCB surface and carefully solder the leads

2- Make sure the solder joints are cone-shaped and shiny

3- Trim excess leads as close as possible to the solder joint

REMOVE THEM FROM THE TAPE ONE AT A TIME !

AXIAL COMPONENTS ARE TAPED IN THE CORRECT

MOUNTING SEQUENCE !

You will find the colour code for the resistances and the LEDs in the HALG

(general manual) and on our website: http://www.velleman.be/common/service.aspx

 R1 : 240K (2 - 4 - 0 - 3 - 1)

 R3 : 3K (3 - 0 - 0 - 1 - 1)

 R4 : 4K7 (4 - 7 - 0 - 1 - 1)

 R5 : 10K (1 - 0 - 0 - 2 - 1)

 R6 : 1K8 (1- 8 - 0 - 1 - 1)

1. Metal film resistors

R...

Construction

 D1 : 1N4007

4. Diode. Watch the polarity !

 C1 : 470pF (471)

 C2 : 470pF (471)

2. Capacitors.

C...

CATHODE D...

 IC1 : 8p

 IC2 : 16p

3. IC socket. Watch the

position of the notch!

 R2 : 18K (1 - 8 - 0 - 2 - 1)

 R7 : 1K8 (1 - 8 - 0 - 1 - 1)

 Attention : because one of the

connections of both R2 and R7

is a measuring point, it is advis-

able to take care that the body of

the resistors is on the largest

circle of the pcb overprint.

5. Metal film resistors

R...

 R8 : 560 (5 - 6 - 1 - B)

6. Resistor

R...

Construction

 C3 : 470nF (µ47)

8. Capacitor.

 RV1 : 1K (OFFSET)

 RV2 : 200K (ZERO)

 RV3 : 5K (GAIN)

Offset : Zero-setting of the sensor.

Zero : Calibration at zero degrees.

Gain : Maximum temperature

calibration.

7. Multiturn trimmers

RV...

 C4 : 10µF

 C5 : 10µF

 C6 : 10µF

 C7 : 220µF

10. Electrolytic Capacitors.

Watch the polarity !

C...

 J1 : 2p + 3p

9. Terminal block connectors

 IC1 : TLV721 or eq.

 IC2 : 3524 or eq.

11. IC’s. Watch the position

of the notch!

Preparing the sensor

 Cut two 5cm pieces of the supplied copper wire (fig. 1.1). Using a knife, remove the varnish of both

pieces of wire over some 3mm from the ends and tin the ends (fig. 1.1)

 Cut the connections of the KTY11, KTY81-22 sensor or eq. at 3mm (fig. 1.2)

 Solder both copper wires to the sensor (fig. 1.3)

12. Preparing the sensor

Fig. 1.1

Fig. 1.3

Fig. 1.2

 Cut off a piece of shrinking tube with a length equal to 5cm

 Slide the shrinking tube over the copper wires and OVER the sensor (fig. 1.4)

 Heat the shrinking tube using a hair dryer or, better still, using a paint stripper.

 Connect the transmitter (type KTY11, KTY81-22 or equivalent) with the points SENSOR of the pcb, using

a piece of screened wire (+/- 50cm). The polarity is of no importance.

Fig. 1.4

Preparing the sensor

 IMPORTANT : First have the circuit "warmed up" for about 10 minutes before starting adjusting!

 Connect the transmitter (type KTY11, KTY81-22 or equivalent) with the points SENSOR of the pcb, us-

ing a piece of screened wire (+/- 50cm). The polarity is of no importance.

 Connect a DIGITAL measuring apparatus between the two connection wires of R2 and R7.

 Connect 12VDC to the points +VS and -VS.

REMARK : Be careful to not touch the circuit with your hands while adjusting it, because this could cause

noise at its output, and consequently a very unstable read out.

 Fill a glass with ice cubes and let them melt a little until you get ice-water.

 Plunge the transmitter into the melting ice-water (0°C). Take care that the connection wires of the trans-

mitter do not touch the water.

 Adjust the OFFSET trimming potentiometer RV1, so that the meter indicates 0V (possibly select a more

sensitive measuring range) and wait until the indication becomes stable.

 THIS ADJUSTMENT IS VERY IMPORTANT, SO CARRY IT OUT VERY CAREFULLY!

Adjustment & use

13. Adjustment & use

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Velleman Accessoires

Velleman

Velleman PEM400 Manuel utilisateur

Velleman

Velleman MP1900G Manuel utilisateur

Velleman

Velleman VTUSD3 Manuel utilisateur

Velleman

Velleman PEM7DBI Manuel utilisateur

Velleman

Velleman 3DPEN Manuel utilisateur

Velleman

Velleman RCSOST Manuel utilisateur

Velleman

Velleman CTC1000PIR Manuel utilisateur

Velleman

Velleman Perel EDB8 Manuel utilisateur

Velleman

Velleman Whadda WPSE472 Manuel utilisateur

Velleman

Velleman 3DPEN3 Manuel utilisateur

Velleman

Velleman MP1000 Manuel utilisateur

Velleman

Velleman VMA306 Manuel utilisateur

Velleman

Velleman SHE14 Manuel utilisateur

Velleman

Velleman HAM9011 Manuel utilisateur

Velleman

Velleman CTC1000WS Manuel utilisateur

Velleman

Velleman MM102 Manuel utilisateur

Velleman

Velleman VMA337 Manuel utilisateur

Velleman

Velleman LPP6 Manuel utilisateur

Velleman

Velleman K8067 Manuel utilisateur

Velleman

Velleman MP1800 Manuel utilisateur

Velleman

Velleman VMA340 Manuel utilisateur

Velleman

Velleman VMA339 Manuel utilisateur

Velleman

Velleman ED38105 Manuel utilisateur

Velleman

Velleman PEREL EDP1 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur