Veko Magnus Manuel utilisateur

MANUAL - VEKO LINEAR LIGHTING SYSTEM

IP65

Magnus

This manual is for usage with shown

product families on this page

in IP65 specification only.

In combination with the following

linear lighting profiles:

PWR-05500

•

PWR-05500-B

•

For further information of applicable

profiles, see section 3 of this manual.

Joris

Justin

Manual Veko linear lighting system / IP65 / V04 / 2020-09-29

1/16

Table of contents

Mounting

Coupling

Mounting brackets

Power feed with cable gland

Power feed with Wieland connectors

Single unit (re-) placement

Sensor MD-L (re-) placement

Sensor configuration(s)

Pool

Emergency LED indicator & battery replacement

Emergency system info & disclaimers

General disclaimers

Page

3, 4

11, 12

IP65

2/16

Manual Veko linear lighting system / IP65 / V04 / 2020-09-29 / Table of contents

Mounting - suspension

1 2

1 Disconnect the mains.

2 Example of a light-line.

3 In regular conditions a 2 point suspension

is used.

Note

: a light-line consists of multiple part

segments. the middle linepart may vary in quantity.

Note:

measurement F is half of measurement E,

deviding E equally over 2 lineparts.

4 In case of:

- Cable duct

- Sports utility

- Swimming pool

Always use a suspension with at least 3 points.

IP65

Measurement

Recommended

length (mm)

Maximum

length (mm)

na.

4600

na.

3060

750 1150

2700 2700

2300 2600

1150 1300

ca. 1500

1700

Measurement

Recommended

length (mm)

Maximum

length (mm)

na.

4600

na.

3060

750 1150

ca. 1500

1700

3/16

Manual Veko linear lighting system / IP65 / V04 / 2020-09-29 / Mounting

Mounting

6 7

8 9 10

11 12 13

14 15

6 In case of mounting in concrete ceiling, Veko

recommends a MM04 anchor or similar with

according drill sizes.

7 In case of using a hook on a sheet piling roof

structure, Veko advises to drill the hole in the

center of the profile.

8 Example with KDW-hook, pendula and steel-

wire (left). KDW-hook, chain and S-hook (right).

9 Always close the links of both the KDW-

and S-hook.

10 Close the link of the S-hook.

11 Close the link of the KDW-hook.

12 Example of mounting with threaded end.

13 Example of mounting with caddy.

14/ 15 When the linear lighting is placed inside

the cannelure of the sheet piling, it's recommended to

use a metal strud or strip to secure the linear lighting

to the metal roof structure.

IP65

KDW-Hook

4/16

Manual Veko linear lighting system / IP65 / V04 / 2020-09-29 / Mounting

Coupling

1 2

4 5

7 8

10 11

1 Disconnect the mains before operating

the linear lighting system.

2 Example of connected profiles.

Note

: Profile

and/or brackets may vary.

3 The flatcable is provided with a curl for extra

length for an easy connection. Pull out and ex-

tend the flatcable.

-other.

8 Press profiles together.

9 Tighten Hexagon M5 screws (2x) on both

sides of the profiles.

10 Hook the coupling plate into the profiles.

11 Rotate the plate into position.

12 Tighten the slotted M6 bolts (4x).

IP65

4 Make sure the male connector is positioned

outside the profile, with the backside onto the

edge of the connection plate.

5 Align both profiles.

6 Insert the connector through the plate

and seals.

7 Make sure connectors firmly 'click' into each-

5/16

Manual Veko linear lighting system / IP65 / V04 / 2020-09-29 / Coupling

Overview of mounting brackets and couplings

Profile

Mounting

Coupling

Note:

Applicability of bracket may vary, depending on the surrounding, light-line configuration, light-line application and/ or IP-class.

IP65

6/16

Manual Veko linear lighting system / IP65 / V04 / 2020-09-29 / Bracket overview

Power feed with cable gland

1 2

7 8

10 11 12

13 15

1 Switch off the mains before operating

the linear lighting system.

2 Contents.

3 Use a slotted screwdriver to punch out the

desired hole(s) for the cable gland(s).

4 Remove the remaining piece(s).

5 Fit the cable gland(s).

6 Fasten the cable gland nut(s).

7 Route wiring through the cable gland and

fit with either male or female connector (depen-

ding on counterpart on the linear lighting system).

8 Insert the connector.

9 Connectors should firmly 'click' into eachother.

10 Tighten the M5 hexagon bolts on both sides-

- of the light-line.

11 Hook the coupling plate into the profiles.

12 Rotate the plate into position.

13 Tighten the M6 bolts (4x).

15 After reassuring all electrical connections

are correctly in place and corresponding,

switch the mains back on.

IP65

6543

Item

Qty.

Power Feed

Connection plate

Connector female

Connector male

Cable gland PG13,5

7/16

Manual Veko linear lighting system / IP65 / V04 / 2020-09-29 / Power feed with Cable gland

Power feed Wieland

1 2

6 7

1 Disconnect the mains before operating

the linear lighting system.

2 Contents.

3 Connect the wiring with the flatcable connectors.

4 Connectors should firmly 'click' into eachother.

9 Connect the feed to the main grid using

the Wieland connectors.

10 After reassuring all electrical con-

nections are correctly in place and

corresponding, switch the mains back on.

IP65

89 10

5 Place the feed onto the light-line, aligning the

connection plates. Tighten the M5 Hexagon bolts (2x)

on both sides of the light-line.

6 Hook the coupling plate into the profiles.

7 Rotate the plate into position.

8 Tighten the M6 bolts (4x).

Item

Qty.

Power feed

Coupling plate (with

4x slotted M5 bolt)

8/16

Manual Veko linear lighting system / IP65 / V04 / 2020-09-29 / Power feed Wieland

Single unit (re-)placement

1 2

4 5 6

1 Disconnect the mains before operating the

linear lighting system.

Note

: Type of unit

and/or profile may vary.

2 Make sure poles and wiring are in correct

position.

3 Insert connector to the flatcable.

4 Press and mount the fallout safety clip into-

9 In case of a sports or emergency unit, place

extra

safety clips onto the unit- and profile,

5 on either side

of the unit, equally devided.

Caution

: Bracket may contain sharp edges.

Caution

: Make sure wiring doesn't get stuck

between the unit and the profile and

is placed

properly inside the linear lighting system.

- the profile.

5 Press the unit into the profile.

6 Mount the sealing and pressure plate(s)

onto the bracket.

7 Tighten the screw(s).

8 Mount the locking clips (6x), 3 on each side

of a single unit or blindplate.

IP65

9/16

Manual Veko linear lighting system / IP65 / V04 / 2020-09-29 / Single unit (re-) placement

Sensor MD-L (re-)placement

1 2 3

4 5 6

7 8

MD-L-Na

MD-L-R

1 Disconnect the mains before operating the

linear lighting system.

2 Example of sensor.

Note

: type of sensor and/or

profile may vary.

3 Make sure poles and wiring are in correct

position.

4 Insert connector to flatcable.

5 Press and mount the fallout safety clip

into the profile.

6 Fit the sensor unit into the profile

7 In case of the narrow lens, a cover

can be used to limit the reach of the

sensor beam if necessary.

- Length -

- Width -

-This cover can be cut to size with pliers

or scissors on the breakline to achieve the desired

reach and angle of the sensor beam.

8 Technical data.

9 Sensor reach:

MD-L-R (round lens)

MD-L-Na (narrow lens)

IP65

Technical data

Power (W)

1,5 W < 4 W (Switched off- < on)

Voltage (V)

220-240 V

Length (mm)

300 mm

Frequency (Hz)

50 ÷ 60 Hz

Circuit

6 A

Sensitivity settings

5 (standard max. sensitivity)

Twilight circuit

Adjustable in 9 steps 0-1.000 Lux

Switch-off delay relay

Relay 0-99 minutes

Environment application

-25 °C - + 35 °C

Corridor function / dynamic switch (example:

10-100 %)

In combination with DALI driver and control

gear

Programming

Readout and re-programmable by colour coding

with LED in sensor

PIR detection angle

Round 130

- 140

ENEC certification

In application at DEKRA

Warrenty

5 years

10/16

Manual Veko linear lighting system / IP65 / V04 / 2020-09-29 / Sensor (re-) placement

Ce manuel convient aux modèles suivants

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur