VDO 333.001 Guide d'installation
Set the cylinder selector switch on the rear of the tachometer to the correct setting for your engine
(4, 6, or 8 cylinders).
Note: The red or black wire MUST be removed before adjustment to the cylinder setting, which is made from
the 田ylinder selector・switch.
Use a small screwdriver or similar object to reach into the recess. An ink pen works well.
Choose the best mounting position for your particular vehicle. Do not mount the tachometer in a
position that will impair visibility or interfere with driving. Before drilling into the mounting
surface. Look for any hidden wiring or other components that could be damaged by the drill
bit as it passes through. After mounting the tachometer, connect the wires as follows.
Disconnect negative (-) battery cable from your car battery.
Connect green wire from back of tachometer to vehicle's tachometer signal source.
CAUTION: You must consult your service manual to ensure the proper connection. If using an
aftermarket ignition system, be sure to follow the manufacturer's instructions.
Failure to do so can ruin your tachometer.
Connect black wire from back of gauge to a good engine ground. Do not assume that any part
of the chassis is a good ground. Use abrasive paper to clean any surface that will be serv-
ing as your ground connection.
Connect red wire to +12 Volt source that is energized only when the key is on the "on" position.
This can be at the fuse box or the ignition switch "on" position.
Connect yellow wire from back of gauge to 12 Volt terminal on ignition switch or other
switchable 12 Volt power source.
Reconnect negative (-) battery cable.
Final testing: Push the "Light" button to change the back light to 7 different color, Once a color
is selected, the tachometer will not change colors automatically. To resume this automatic
change of colors, press and hold the light button until it changes to the next color and then
release it.
Shift Light Operation
To see the RPM for the shift light:
Push the mode button "M" until the "set" green LED light is on, then push either the up or down
arrow button until the needle moves to the desired RPM.
Next, push the mode button "M" again, the "set" green LED light will go off and the tachometer will
return to the standard function.
Installation p/n 333.001
Ignition
Coil
Elect. Ign.
Module
Distributor
Green Signal
Red + 12V Ign.
Black Negative
(Earth)
Yellow Illumination + 12V
FA 18 July 2011
Set the cylinder selector switch on the rear of the tachometer to the correct setting for your
engine (4, 6, or 8 cylinders).
Note: The red or black wire MUST be removed before adjustment to the cylinder setting, which is made from
the 田ylinder selector・switch.
Use a small screwdriver or similar object to reach into the recess. An ink pen works well.
Choose the best mounting position for your particular vehicle. Do not mount the tachometer in a
position that will impair visibility or interfere with driving. Before drilling into the mounting
surface. Look for any hidden wiring or other components that could be damaged by the drill
bit as it passes through. After mounting the tachometer, connect the wires as follows.
Disconnect negative (-) battery cable from your car battery.
Connect green wire from back of tachometer to vehicle's tachometer signal source (Negative
side of ignition coil or the Electronic Ignition Module, tacho output signal).
CAUTION: You must consult your service manual to ensure the proper connection. If using an
aftermarket ignition system, be sure to follow the manufacturer's instructions.
Failure to do so can ruin your tachometer.
Connect black wire from back of gauge to a good engine ground. Do not assume that any part
of the chassis is a good ground. Use abrasive paper to clean any surface that will be serv-
ing as your ground connection.
Connect red wire to +12 Volt source that is energized only when the key is on the "on" position.
This can be at the fuse box or the ignition switch "on" position.
Connect yellow wire from back of gauge to 12 Volt battery
Reconnect negative (-) battery cable.
Final testing: Push the "Light" button to change the back light to 7 different color, Once a color
is selected, the tachometer will not change colors automatically.
To resume this automatic change of colors, press and hold the light button until it changes
to the next color and then release it.
Shift Light Operation
To see the RPM for the shift light:
Push the mode button "M" until the "set" green LED light is on, then push either the up or down
arrow button until the needle moves to the desired RPM.
Next, push the mode button "M" again, the "set" green LED light will go off and the tachometer will
return to the standard function.
Installation p/n 333.201
Ignition
Coil
Elect. Ign.
Module
Distributor
Green Signal
Red + 12V Ign.
Black Negative
(Earth)
Yellow Battery + 12V
FA 18 July 2011
Set the cylinder selector switch on the rear of the tachometer to the correct setting for your engine (4, 6, or 8
cylinders).
Note: The red or black wire MUST be removed before adjustment to the cylinder setting, which is made from the
田ylinder selector・switch.
Use a small screwdriver or similar object to reach into the recess. An ink pen works well.
Choose the best mounting position for your particular vehicle. Do not mount the tachometer in a position that
will impair visibility or interfere with driving. Before drilling into the mounting surface. Look for any hidden
wiring or other components that could be damaged by the drill bit as it passes through.
WIRING
Disconnect negative (-) battery cable from your car battery.
Connect green wire from back of tachometer to vehicle's tachometer signal source.
CAUTION: You must consult your service manual to ensure the proper connection.
If using an aftermarket ignition system, be sure to follow the manufacturer's instructions.
Connect black wire from back of gauge to a good engine ground. Do not assume that any part of the chas-
sis is a good ground.
Use abrasive paper to clean any surface that will be serving as your ground connection.
Connect red wire to +12 Volt source that is energized only when the key is on the "on" position. This can be
at the fuse box or the ignition switch "on" position.
Connect yellow wire from back of gauge to 12 Volt terminal on ignition switch or other switchable 12 Volt
power source.
Connect Blue/White wire from back of gauge to Temp sensor
Connect Orange wire from back of gauge to Pressure sensor terminal, connect other terminal to negative
Reconnect negative (-) battery cable.
Start engine for 5 to 10 minutes to see temperature change.
After starting engine, check for oil leaks at the pressure sender unit connection point.
Final testing: Push the "Light" button to change the back light to 7 different color, Once a color is selected,
the tachometer will not change colors automatically. To resume this automatic change of colors, press
and hold the light button until it changes to the next color and then release it.
Shift Light Operation
To see the RPM for the shift light: Push the mode button "M" until the "set" green LED light is on, then push ei-
ther the up or down arrow button until the needle moves to the desired RPM. Next, push the mode button "M"
again, the "set" green LED light will go off and the tachometer will return to the standard function.
Installation p/n 333.002
Ignition
Coil
Elect. Ign.
Module
Distributor
Green Signal
Red + 12V Ign.
Black Negative
(Earth)
Yellow Illumination + 12V
Blue/White Temp Sender
Orange Pressure sender
8 - 6 - 4 Cyl Setting at rear of Tacho
FA 18 July 2011
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels VDO Instrument de mesure
VDO
VDO CONTISYS SCAN Manuel utilisateur
VDO
VDO CONTISYS OBD - V3.0 Manuel utilisateur
VDO
VDO VIEWLINE TACHOMETER Manuel utilisateur
VDO
VDO TACHOMETER Manuel utilisateur
VDO
VDO TU00-0752-9207102 Manuel utilisateur
VDO
VDO Viewline 110 mm Manuel utilisateur
VDO
VDO CONTISYS OBD - Manuel utilisateur
VDO
VDO OCEANLINK - Manuel utilisateur
VDO
VDO VIEWLINE SPEEDOMETER Manuel utilisateur
VDO
VDO CONTISYS OBD - Manuel utilisateur
VDO
VDO CONTISYS OBD PROFESSIONAL Manuel utilisateur
VDO
VDO CONTISYS OBD - APPLICATION LIST V2.0 Manuel utilisateur
VDO
VDO TU00-0752-5607150 Manuel utilisateur
VDO
VDO TU00-0752-5807102 Manuel utilisateur
VDO
VDO CANcockpit Series Manuel utilisateur
VDO
VDO VIEWLINE AMMETER Manuel utilisateur
VDO
VDO Viewline TU00-0752-8707102 Manuel utilisateur
VDO
VDO CONTISYS OBD - Manuel utilisateur
VDO
VDO VIEWLINE TACHOMETER WITHOUT LCD Manuel utilisateur
VDO
VDO Ocean Link Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur