VDO Cyclecomputing C05 Manuel utilisateur
BEDIENUNGSANLEITUNG
INSTRUCTION MANUAL
MANUEL D´INSTALLATION ET D´UTILISATION
MANUALE D´INSTALLAZIONE E FUNZIONAMENTO
INSTALACION Y OPERACIÓN MANUAL
HANDLEIDING
NÁVOD K MONTÁŽI A OBSLUZE
INSTRUKCJA OBSLUGI LICZNIKA
INSTALLATIONS OG BETJENINGSVEJLEDNING
BRUKSANVISNING
BRUKSANVISNING
ASENNUS JA KÄYTTÖOHJEKIRJA
CYCLECOMPUTING
C05
1
INSTALLATION AND OPERATION MANUAL - VDO CYTEC C 05
Preface
Thank you for buying a VDO CYTEC bicycle computer. The more familiar you get with this model, the more
enjoyable your trips are going to be.
Please read thoroughly all the information provided in this manual. You are getting important and useful hints
for operation to make you fully benefit from all the technical features of your VDO CYTEC bicycle computer.
We wish you enjoyable trips and rides on your bike with VDO CYTEC CYCLE PARTS GMBH
1.Mounting the system
1.1 Mounting the handlebar holder
The handlebar holder fits handlebars of any diameter. Before mounting the system, decide if you will be using
your left or right hand to operate the computer and then mount the handlebar holder on the respective side.
Position the handlebar holder, insert the strap and adjust is by tightening the screw.
GB
screw
screw
GB
2
Warning: Before tightening the handlebar holder, make sure to adjust the position of the computer head
(inclination) when the LCD-display is best visible for you. Only when you find the best position
tighten the screw.
1.2 Mounting the speed transmitter
The sensor should be mounted on the same side of the fork as the holder is on the handlebar.
For mounting put the included rubber shim under the sensor and use the cable ties.
Watch out: Do not tighten the cable ties yet! Accurately position the spoke magnet and the sensor first,
then tighten the cable ties. 3
GB
1-5mm
1-5mm
1.3 Mounting the spoke magnet
Distance between magnet and sensor
should be approx. 1-5 mm.
In case this distance is not achievable
in the current positioning, slide the
sensor and the magnet on the fork or
spoke accordingly.
GB
4
3V CR 2032
AC
AC AC
OPEN CLOSE
3V CR 2032
AC
AC AC
OPEN CLOSE
1.4 Installing battery into computer head
To save battery power, your VDO CYTEC C 05 comes with the battery not yet fitted. Prior to initial use you
have to install the battery first. Insert battery with positive (+) end on top.
Watch out: Once the battery is properly fitted, the computer immediately changes into set-up mode
(see also chapter 5). If you find the computer is not functioning properly after a battery
change, push the AC-button (Auto Clear) on the rear side of the computer to reset.
5
GB
1.5 Function Indicator
Your VDO CYTEC C05 features a function indicator ((1)).
When you are done mounting the computer, ((1)) flashes at the first rotation of the wheel.
When the wheel-size is properly entered, actual speed is displayed as well.(see chapter 5).
In case the function-indicator ((1)) is not flashing, please double-check:
Is the computer properly fitted onto the handlebar holder?
Is the spoke magnet accurately positioned opposite the speed transmitter (max 5 mm distance)?
2. Twist-Click mounting of computer onto holder
The Twist-Click mounting has been exclusively developed for the new line of VDO CYTEC computers.
The computerhead is put onto the handlebar and by a right turn of the computerhead (TWIST) fixed to the
holder (CLICK).It is just as easy to remove the computerhead from the handlebar holder.
Slightly push the computerhead down, twist it to the left, remove computerhead from handlebar holder.
GB
6
UNLOCK
LOCK
1.LOCK
2.CLICK
1.PRESS
2.UNLOCK
7
GB
Function
DST
ATM
CLK
ODO
GB
8
3. Information features of your VDO CYTEC C 05
Your VDO CYTEC C 05 provides you with following information:
KMH-MPH current speed indicated in either KMH or MPH, featuring automatic conversion into MPH
DST trip counter, counts your trip distance up to 999,99 km or miles.
ATM trip timer, keeps track of the actual riding time featuring automatic start/stop function,
up to 9:59:59 (hrs:min:sec)
CLK clock with 24 h display mode.
ODO odometer, counting distance ridden up to 99,999 KM or M.
4. Operating your VDO CYTEC C 05
Button / Key Covering
Your VDO CYTEC C 05 has 1operating button / key
This button / key has several functions.
All functions of the button / key are outlined in the chart below.
Your display Button / Key to Length of pushing What is going on?
indicates following be pushed the button / key
information
DST-ODO-CLK-ATM push MODE key brief (0.1 sec) next information from DST or ODO orATM
is indicated.
ODO push MODE key long (5 sec) enter set-up mode for wheelsize and odometer
CLK push MODE key long (5 sec) enter set-up mode for clock
DST push MODE key long (5 sec) DST andATM are simultaneously reset to ZERO
Watch out: To avoid resetting DST and ATM by mistake, thoroughly check the information in display
before you push the MODE key for 5 sec.
5. Set-up mode
Your VDO CYTEC C 05 features the following set-up procedures Watch out:Once the battery is properly
fitted, your VDO CYTEC C 05
wheelsize = WS set-up starts out of ODO in display immediately changes into
clock = CLK set-up starts out of CLK in display set-up mode
odometer = ODO set-up starts out of ODO in display (see also chapter 5.3). 9
GB
Table des matières
Autres manuels VDO Cyclecomputing Accessoires pour vélos
VDO Cyclecomputing
VDO Cyclecomputing A4+ Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing ECO LIGHT RED Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing Z2 Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing X2 Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing ECO LIGHT RED Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing Z2 Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing A4 Plus Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing M3 WR Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing R4GPS Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing M6.1 Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing R4GPS Comment utiliser
VDO Cyclecomputing
VDO Cyclecomputing Z1 Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing R5GPS Comment utiliser
VDO Cyclecomputing
VDO Cyclecomputing C1DS Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing Cytec C05+ Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing Z3 PC-LINK Manuel
VDO Cyclecomputing
VDO Cyclecomputing ECO LIGHT RED PLUS Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing M2 WR Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing A8 Manuel utilisateur
VDO Cyclecomputing
VDO Cyclecomputing x3dw Manuel utilisateur
