VarTech Systems VTPC2100VS Manuel utilisateur
Solutions for Demanding Applications
VARTECH
S Y S T E M S I N C.
21.5” Wide Format Class 1 - Division 2 Certified
VESA Mount Enclosed PC
Model VTPC2100VS / VTPC2100VS Video Monitor
User’s Guide
Read these instructions completely before attempting to operate your new VESA Mount PC
Revision History
Date Rev No Summary Page
12/04/17 00 First Issue
Safety Instructions
PLEASE NOTE - This equipment is suitable for use in Class I, Division 2 or non-hazardous
locations only.
WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS
BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.
AVERTISSEMENT - RISQE D'EXPLOSION - AVANT DE DECONNECTER L'EQUIPMENT, COUPER
LE COURANT OU S'ASSURER QUE L'EMPLACEMENT EST DESIGNE NON DANGEREUX.
Read the Safety Instructions carefully and keep it for use later.
The chassis metalwork of the module must be installed properly to the main earthing termination
for Class 1 equipment.
Care must be exercised in the application of the system to prevent overheating. Ensure that the
ambient temperature around the system does not exceed 60°C and provide adequate means of
ventilation to achieve this.
When cleaning cut off the electrical supply at all times. Never use liquid or aerosol detergent,
use a soft damp cloth instead.
To avoid electric shock, never touch the inside of the system. There are no user adjustable
components inside, only a qualified technician should open the system’s case.
If the system does not operate normally – in particular, if there are any unusual sounds or smells
coming from it – disconnect it immediately.
Do not put pressure on the LCD panel screen because it is very fragile.
Always handle the system with care when moving it.
Take care that the system is disposed of correctly at the end of its life. If in doubt refer to your
local ordinances or regulations for proper disposal.
User to supply appropriate lockable type plug and power disconnecting switch.
The end user must either supply a switch to their power outlet suitable for Class 1, Division 2
use (if adjacent to the power outlet), or locate the said switch outside the hazardous area.
This equipment is suitable for use in a Class 1, Division 2, Groups A, B, C, and D or non-
hazardous location only.
Explosion Hazard - Substitution of components may impair suitability for hazardous locations.
Any Equipment or associated cabling connected to this device must be non-incendive and/or
suitable for the Class 1, Division 2 area in which it is to be installed.
Hazardous Locations:
This equipment is suitable only for the locations specified on the product nameplate, specifically:
Class I, Division 2 Groups A, B, C, D
Non-hazardous locations
The following statement applies to use in hazardous locations:
WARNING! Explosion Hazard
Substitution of components may impair suitability for hazardous locations.
Do not disconnect equipment unless power has been switched off and area is
known to be non-hazardous.
Do not connect or disconnect components unless power has been switched off.
All wiring must comply with NEC 2014 articles are 501.10(B), 502.10(B), and
503.10(B) as appropriate.
Peripheral equipment must be suitable for the location in which it is used.
This equipment has an operating temperature code of T4 when operating in a
60`C (140`F) ambient environment. Do not install this product in environments
where atmospheric gases have an ignition temperature of less than 135`C
(275`F).
Environment and Enclosure Information:
Review this information on enclosures before installing the product:
ATTENTION: Environment and Enclosure
This equipment is intended for use in a Pollution Class 2 industrial environment, in
overvoltage Category II applications (as defined in IEC publication 60664-1), at
altitudes up to 2000 meters (6561 feet).
See NEMA Standards publication 250 and IEC publication 60529, as applicable,
for explanations of the degrees of protection provided by different types of
enclosures. The user may also reference the Industrial Automation Wiring and
Grounding Guidelines, publication 1770-4.1, for additional installation
requirements pertaining to this equipment.
Cleaning the LCD monitor
To clean the LCD panel:
Wipe the screen gently with a clean lens brush made of camel hair, or a soft, clean, lint free
cloth. This is to remove dust and other particles without scratching the LCD panel.
If it is still not clean, then wipe with a damp lint free cloth and blow on it to dry.
Do not clean the panel with a keton-type material (e.g. acetone), or ethyl toluene, ethyl acid, methyl
or chloride. These may damage the LCD panel.
Do not apply pressure to the LCD panel.
Standard Technical Specifications:
LCD Monitor:
Size / Type 21.5” 1080P Full HD TFT LCD
Native Resolution 1920 x 1080
Contrast Ratio 5000:1
Viewing Angles Horizontal: 178°
Vertical: 178°
Pixel Pitch 248.25mm x 248.25mm
Brightness (typical) 300 cd/m²
Response Time (typical) 25ms GTG(Avg. Typ.)
Colors Supported 16.7 million
Computer System:
Processor 2.0GHz Quad Core Intel® Celeron® Processor J1900
System Memory 4GB DDR3L-1333 SO-DIMM x 1
BIOS AMI
Hard Drive 500 GB SATA
Operating System Windows 10 - 32 bit
I/O Ports 2 x LAN
3 x RS-232
1 x RS-422/485
2 x USB 2.0
1 x Power Connector
Graphics
Intel® HD Graphics
LAN 2 x 10/100/1000Mbs support Wake-on-LAN
Touch Screen Resistive Touch
Touch Screen Interface USB
Power & Operational Specifications:
Power Input 100 - 220 VAC 1.5A
Power Consumption 60W
Temperature Operational: -32°F to 122°F 0°C to 50°C
Storage: -4°F to 140°F -20°C to 60°C
Humidity Operational: 20 to 40°C, 90% RH NC
Storage: 5 to 65°C, 28% RH NC
Installation of Your VESA Mount PC
Packaged with each carton will be:
1 – VTPC2100VS
1 - Users Guide (Printed or on CD/Flash Drive)
BEFORE MAKING ANY CONNECTIONS OR APPLYING POWER,
FIRST READ THROUGH THE ENTIRE MANUAL
Mounting Procedure
VESA Panel Mounting Procedure:
1- Install the enclosure to a 100mm VESA mount pedestal.
2- Secure the enclosure using the screws and lock washers, supplied with the unit.
VESA Mount Drawing: Detail –A–
Connections to the VESA Mount PC
Bottom Rear View
-Connector Panel-
Autres manuels VarTech Systems Moniteur
VarTech Systems
VarTech Systems DiamondVue VT084C Manuel utilisateur
VarTech Systems
VarTech Systems VT420D Manuel utilisateur
VarTech Systems
VarTech Systems VT181CH Manuel utilisateur
VarTech Systems
VarTech Systems VT170CM Manuel utilisateur
VarTech Systems
VarTech Systems VT121 DiamondVue Series Manuel utilisateur
VarTech Systems
VarTech Systems VT190PVS Manuel utilisateur
VarTech Systems
VarTech Systems VT064C Manuel utilisateur
VarTech Systems
VarTech Systems VT121XA4 Manuel utilisateur
VarTech Systems
VarTech Systems VT190P2 Manuel utilisateur
VarTech Systems
VarTech Systems VT150CHB Manuel utilisateur
VarTech Systems
VarTech Systems VT420W Manuel utilisateur
VarTech Systems
VarTech Systems VT201CM Manuel utilisateur
VarTech Systems
VarTech Systems VTPC150XPE Manuel utilisateur
VarTech Systems
VarTech Systems VT19B-PW Manuel utilisateur
VarTech Systems
VarTech Systems VT170W Manuel utilisateur
VarTech Systems
VarTech Systems VT064P Manuel utilisateur
VarTech Systems
VarTech Systems ColorVue VT190PC Manuel utilisateur
VarTech Systems
VarTech Systems VT420 Series Manuel utilisateur
VarTech Systems
VarTech Systems VT181R2 Manuel utilisateur
VarTech Systems
VarTech Systems VT14A-D Manuel utilisateur
