Varimixer W30 Manuel utilisateur

Autres manuels pour W30

1

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Varimixer Mixer

Varimixer

Varimixer TEDDY W5A Manuel utilisateur

Varimixer

Varimixer AR Series Manuel utilisateur

Varimixer

Varimixer W100PL Manuel utilisateur

Varimixer

Varimixer ERGO60 Manuel utilisateur

Varimixer

Varimixer W30 Mode d’emploi

Varimixer

Varimixer W80 Mode d’emploi

Varimixer

Varimixer V150PLM Manuel utilisateur

Varimixer

Varimixer V30K Mode d’emploi

Varimixer

Varimixer V80 Mode d’emploi

Varimixer

Varimixer V150PL Mode d’emploi

Varimixer

Varimixer V20K Mode d’emploi

Varimixer

Varimixer V30 Manuel utilisateur

Varimixer

Varimixer KODIAK10 Manuel utilisateur

Varimixer

Varimixer W20SF Manuel utilisateur

Varimixer

Varimixer RN Series Manuel utilisateur

Varimixer

Varimixer AR100 VL-1L Manuel utilisateur

Varimixer

Varimixer W20A Mode d’emploi

Varimixer

Varimixer V20 Manuel utilisateur

Varimixer

Varimixer KODIAK V20KT Mode d’emploi

Varimixer

Varimixer W20 F Mode d’emploi

Varimixer

Varimixer W20D Mode d’emploi

Varimixer

Varimixer W20P Manuel utilisateur

Varimixer

Varimixer AR80 Series Manuel utilisateur

Varimixer

Varimixer AR30 VL-1S Manuel utilisateur

Manuels Mixer populaires d'autres marques

Bosch

Bosch GRW 9 Manuel utilisateur

MULTIQUIP

MULTIQUIP Whiteman WM45E Mode d’emploi

KitchenAid

KitchenAid KSM7581BZ0 Guide rapide

Jay-Lor

Jay-Lor 5050 Manuel utilisateur

Sunbeam

Sunbeam FPSBSM210X Manuel utilisateur

MULTIQUIP

MULTIQUIP Whiteman MC94S Mode d’emploi

Thinky

Thinky ARE-250 Manuel utilisateur

Midas

Midas XL4 Manuel utilisateur

bianco

bianco PURO 4 Manuel utilisateur

Paso

Paso DAG9200 Manuel utilisateur

Sima

Sima SFX-9A Manuel utilisateur

better chef

better chef IM-815WC Instructions d'installation

ALLEN & HEATH

ALLEN & HEATH GR1 Manuel utilisateur

Lacor

Lacor 69083 Fiche technique

M-Audio

M-Audio Midiman SAM Manuel utilisateur

Buffalo

Buffalo CP921 Manuel utilisateur

Pentair

Pentair HYPRO Cleanload 3376-0870 Instructions de fonctionnement

Cuisinart

Cuisinart SM50WHE Manuel utilisateur

PLEASE REFER TO THE DIAGRAM ON PAGE 2

1REMOVE NUT (J) AND SHIM WASHERS (H)

2 PRY OFF FORK ASSEMBLY (X).

3 REMOVE SPECIAL V-BELT (A).

4 REMOVE TWO 17MM BOLTS (V)

5 REMOVE 4 BOLTS FROM MOTORPLATE (T).

6 ON OLDER MODEL MIXERS WITH SINGLE PHASE MOTORS,IT MAY BE NECESSARY

TO DISCONNECT THE START & RUN CAPACITORS FROM THE SIDE OF THE

MOTOR BEFORE LIFTING THE MOTOR OUT OF THE MIXER.

7 LIFT MOTOR OUT OF MIXER BODY. SET MOTOR ASSEMBLY ON A BOARD LAYED

ACROSS THE TOP OF THE MIXER.

8 DISCONNECT WIRE HARNESS FROM MOTOR.

NOTE: DO NOT FOLLOW STEPS 9-12 IF YOU ARE REPLACING THE WHOLE

ASSEMBLY. (MOTOR ,GEARBOX,MOTOR PLATE AND PULLEY.

9 GRASP TOP PULLEY (W) AND BANG AGAINST CLAMPING RING & WASHER (S)

THIS ACTION WILL REMOVE PULLEY FROM MOTOR SHAFT.

10 REMOVE 4 SLOTTED HEAD SCREWS FROM MOTOR PLATE TO MOTOR.

REMOVE MOTOR PLATE.

11 INSTALL MOTOR PLATE ONTO MOTOR,TIGHTEN 4 SLOTTED HEAD SCREWS.

INSURE CAPACITORS WILL FACE THE REAR OF THE MIXER WHEN MOTOR IS

INSTALLED.

12 INSTALL MOTOR PULLEY ONTO MOTOR SHAFT,TAKING CARE TO ALIGN KEY WITH KEYWAY. BANG TOP PULLEY AGAINST BOTTOM

PULLEY UNTIL INSTALLED.

13 PLACE MOTOR ON TOP OF MIXER AND CONNECT MOTOR TO HARNESS. (FOLLOW DIAGRAM

ON MOTOR)

14 LOWER MOTOR INTO MIXER BODY.INSTALL 4 BOLTS (T) TO THE MOTOR PLATE. DO NOT TIGHTEN!

15 INSTALL 2 17MM BOLTS (V)

16 MEASURING THE DISTANCE BETWEEN PULLEYS (B),ON 30QT. & 40 QT. THE

DISTANCE SHOULD BE 11 1/2 INCHES.SLIDE MOTOR TO REACH THIS DISTANCE.

ON 60QT.-150QT.,THE DISTANCE SHOULD BE 12 1/4"S.

17 TIGHTEN 13 MM BOLTS (T) AND 17 MM BOLTS (V).

NEXT PAGE

Motor Removal Instructions

Models W30-W150

Motor Removal Instructions

Models W30-W150

18 INSTALL SPECIAL V-BELT (A).

19 INSTALL FORK ASSEMBLY (X).

20 INSTALL WASHERS (G) (H) AND NUT (J).DO NOT TIGHTEN NUT.

21 START THE MIXER AND TIGHTEN THE NUT (J).

DO NOT OVERTIGHTEN!

22 ON THE FRONT PULLEY SET,THE STUD (K) ON THE VARISPEED COLLAR (L) MUST BE PLACED

INSIDE THE LOWER FORK (M),AND ON THE REAR PULLEY SET OUTSIDE THE FORK (N).

23 ADJUST THE SPEED BY TURNING THE THE STOP SCREWS (O) IN OR OUT.

24 THE STOP SCREWS (O) ON THE SPEED LEVER SHOULD BE ADJUSTED SO THAT THE

MEASUREMENT (P) IS 1-2MM ON THE FRONT AND REAR PULLEY,AT HIGH AND LOW SPEED,

RESPECTIVELY.TIGHTEN THE JAM NUTS (R) WHEN THE SPEED IS CORRECTLY ADJUSTED.

Motor Removal Instructions

Models W30-W150