Vanco EVMX4444 Manuel utilisateur
Vanco Part Number
EVMX4444
HDMI® 4x4 Matrix
Selector Switch
www.vanco1.com • 800.626.6445
HDMI® 4x4 MATRIX
SELECTOR SWITCH
www.vanco1.com 800.626.6445
2
1. Do not expose this unit to water,
moisture, or excessive humidity.
2. Do not install or place this unit
in a built-in cabinet, or other
conned space without adequate
ventilation.
3. To prevent risk of electrical shock
or re hazard, due to overheating
do not obstruct unit’s ventilation
openings.
4. Do not install near any source of
heat, including other units that
may produce heat.
5. Do not place unit near ames.
6. Only clean unit with a dry cloth.
7. Unplug unit during lightening
storms or when not used for
an extended period of time.
A surge protector is strongly
recommended.
8. Protect the power cord from
being walked on or pinched,
particularly at the plugs.
9. Use unit only with accessories
specied by the manufacturer.
10. Refer all servicing to qualied
personnel.
CAUTION
HDMI is a very complex technology requiring continuous authentication of the signal
and the same video resolution and audio settings on all electronic equipment in the
system. When there are multiple sources and displays, the video resolution and
audio setting on all connected units must be adjusted to correspond with that of the
display having the lowest video and audio capability.
WARNING
DEAR CUSTOMER
Thank you for purchasing this product.
For optimum performance and safety, please
read these instructions carefully before connecting,
operating or adjusting this product. Please keep this
manual for future reference.
This product is 100% inspected and tested in the United
States to verify HDMI performance parameters.
www.vanco1.com 800.626.6445 3
INTRODUCTION
The Evolution by Vanco EVMX4444 HDMI 4x4 Matrix Selector Switch allows 4 HDMI
sources to be distributed to up to 4 displays simultaneously. Have multiple sources
displayed simultaneously on any display or have a single source duplicated on multiple
displays, exibility for the perfect solution. With an output bandwidth of 6.75 Gbps over
HDMI, the EVMX4444 is capable of full 1080p HD video and HD multi-channel audio
distribution with simple control using the front panel or remotely via IR Receivers at display
locations. Also features EDID management, which allows and encourages source and
display “handshake” for seamless integration. In addition, EVMX4444 is also equipped with
RS-232 and LAN connectivity which allows for rmware updates and third party integration.
For reliable, no-nonsense HDMI distribution and control on a budget, over short distances,
the EVMX4444 Matrix Selector Switch is a great choice for any application.
FEATURES
HDMI® 4x4 Matrix Selector Switch
Part # EVMX4444
• Allows up to 4 HDMI sources to be distributed simultaneously to up to 4 displays
• 1080p HD Matrix Switcher providing a perfect solution for Home or Retail AV as well
as Commercial and Hospitality installations on a budget
• Features EDID management which supports default HDMI EDID and has the ability to
learn the EDID of display equipment for any “handshake” issues
• HDCP Compliant
• Supports HDMI Deep Color and 3D
• Supports 7.1 channel digital audio
• Wideband bi-directional IR pass-through (20 to 60 kHz)
• Choose from 5 switching modes – front panel buttons, Local remote control, RS232
control, IR call-back (dedicated IR extension cable connected to IR extension port, and
IR emitters on sources required), and Ethernet control
• Easy installation with rack-mounting and wall-mounting design, rack mounting ear set
included
• Dimensions: 14.6”(371mm)Wx1.57”(40mm)Hx4.65”(118mm)D
www.vanco1.com 800.626.6445
4
SPECIFICATIONS
TECHNICAL SPECS
HDCP Compliance...................................................... Yes
Video Bandwidth ........................................................ Single-link 225Mhz [6.75 Gbps]
Video Support ........................................................... 480i/480p/720p/1080i/1080p @60 36-bit color
Audio Support ........................................................... Surround Sound (up to 7.1 ch) or stereo digital audio
ESD Protection .......................................................... [1] Human body model — ±19kV [air-gap discharge]
& ±12kV [contact discharge] [2] Core chipset — ±8kV
PCB stack-up ............................................................ 4-layer board [impedance control — differential
100Ω; single 50Ω]
Input ........................................................................ 4x HDMI / 1x RS-232 / 1x Ethernet / 1x IR socket for
IR receiver
Output...................................................................... 4x HDMI
HDMI connector ........................................................ Type A 19 pin female
RJ-45 connector........................................................ WE/SS 8P8C with 2 LED indicators
RS-232 connector ..................................................... DE-9 [9-pin D-sub female]
3.5mm connector ...................................................... [System IR] Receives IR commands from remote
control
MECHANICAL SPECS
Housing .................................................................... Metal enclosure
Fixedness.................................................................. 1RU rack-mount with ears
Power supply............................................................. 5V 4A DC
Power consumption.................................................... 20 Watts [max]
Operation temperature............................................... 32-104 degrees F
Storage temperature.................................................. -4 - 140 degrees F
Relative humidity ....................................................... 20-90% RH (no condensation)
PACKAGE CONTENTS
• (1) EVMX4444 HDMI 4x4 Matrix Selector Switch
• (5) IR Receiver (RX)
• (4) IR Blaster (TX)
• (1) DC 5V4A in-line with C7 power cord
• (1) Rack-mounting ear set
• (1) IR remote control
• (1) Installation software CD
• (1) User Manual
www.vanco1.com 800.626.6445 5
1. Power Switch:
2. Port 1-4: Input source channels mapping LED for each output channel
3. Port 1-4 Select: Push button for selecting input channels
4. Source Status: Input source indicator LED
5. IR SENSOR: IR sensor for receiving the IR commands from IR remote
6. LED: Power indicator
7. RS-232: RS-232 control port
8. Ethernet: Ethernet control port
9. IR Blaster 1-4: 3.5mm IR blaster socket for individual HDMI source contro
10. INPUT 1-4: HDMI inputs
11. IR Receiver 1-4: Infrared 3.5mm socket for plugging in the extension cable of IR
receiver
12. OUTPUT 1-4: HDMI outputs
13. System IR Receiver: Ext. IR receiver
14. All IR Output: 3.5mm IR blaster socket for HDMI source control on all 4 inputs
15. +5V DC: 5V DC power jack
PANEL DESCRIPTIONS
7 8
9
10
11
12
1
2
345 6
151413
www.vanco1.com 800.626.6445
6
EDID
The EDID switch allows for EDID learning or to pre-set an EDID to encourage a “handshake” between the
display and source.
The EDID learning function is only necessary whenever any display on the HDMI output port is not outputting
audio and video properly. Because the HDMI source devices and displays may have various level of capability in
playing audio and video, the general principle is that the source device will output the lowest standards in audio
format and video resolutions to be acceptable among all HDMI displays connected. In this case, a 720p stereo
HDMI signal output would be probably the safest choice. The EDID function can also force the matrix to learn
the EDID of the lowest capable HDMI display among others to make sure all displays are capable to play the
HDMI signals normally.
There are two methods for EDID Learning as shown below:
1. IR Remote Control: Please refer to the Operation Control – IR Remote Control
section
2. Software Control: Please refer to the Operation Control – EDID section
EDID Settings:
There are eight embedded default EDID settings as shown below,
1. Full-HD(1080p@60)-24bit 2D & 2ch
2. Full-HD(1080p@60)-24bit 2D & 7.1ch
3. Full-HD(1080p@60)-24bit 3D & 2ch
4. Full-HD(1080p@60)-24bit 3D & 7.1ch
5. HD(1080i@60)(720p@60)-24bit 2D & 2ch
6. HD(1080i@60)(720p@60)-24bit 2D & 7.1ch
7. Full-HD(1080p@60)-36bit 2D & 2ch
8. Full-HD(1080p@60)-36bit 2D & 7.1ch
www.vanco1.com 800.626.6445 7
OPERATION CONTROL - IR
REMOTE CONTROL
1. INPUT/OUTPUT Switch - Push the corresponding button on the remote to select Input & Output port.
Ex: Select Input 2 to Output 3 - The button highlighted in the red circle button shown below to select Input 2
to Output 3
2. Function Key
Button Function
OFF Standby mode
ON Power on the matrix switcher
STATUS Preset output status
SAVE Save current mapping mode
PRESET Preset mapping mode
DEFAULT EDID Begin default EDID selection
LEARN EDID Begin EDID learning from one output
CLEAR Clear the previous IR operation procedure
TAKE Trigger the previous setting
F1 Reserved
F2 Reserved
www.vanco1.com 800.626.6445
8
www.vanco1.com 800.626.6445 9
1. System Requirement
1) OS Information: MS WinXP/7
2) Baud rates: 9600
3) Software size: 3 MB
4) Minimum RAM requirement: 256 MB
OPERATION CONTROL – Software control through RS-232
OPERATION CONTROL - SOFTWARE
CONTROL THROUGH RS-232 AND
ETHERNET PORT
1. I/O Routing Button
2. Rename I/O Button
3. EDID Button
4. Network Button
5. F/W Update & Default Reset Button
6. Refresh COM Port
7. COM Port Selection
8. Connection Status
9. Connect/Disconnect Button
10. Control SW via RS-232
11. Control SW via Network
12345
678911
10
www.vanco1.com 800.626.6445
10
1. I/O Routing Button
I/O:
Select the input
Click “Send” to change the I/O setting
Save Mapping:
Select Mapping(1-8)
Click “Save” button to save current mapping
Preset Mapping:
Select Mapping(1-8)
Click “Recall” button to recall previous mapping which are saved
Table des matières
Autres manuels Vanco Changer
Vanco
Vanco Evolution EVMX88PRO Manuel utilisateur
Vanco
Vanco EVMX44QI Manuel utilisateur
Vanco
Vanco Evolution EVSW1042 Manuel utilisateur
Vanco
Vanco Evolution EVMX4K04 Manuel utilisateur
Vanco
Vanco VPW-280794 Manuel utilisateur
Vanco
Vanco Evolution EVSW1041 Manuel
Vanco
Vanco Evolution EVMX44PRO Manuel utilisateur
Vanco
Vanco HDSW4K31 Manuel utilisateur
Vanco
Vanco PULSEAUDIO PA-SW31T Manuel utilisateur
Vanco
Vanco Evolution EVMX4004 Manuel utilisateur
Vanco
Vanco Evolution EVSW21MV Manuel
Vanco
Vanco EVMX4016 Manuel utilisateur
Vanco
Vanco VPW-280789 Manuel utilisateur
Vanco
Vanco HDBT8x7 Manuel utilisateur
Vanco
Vanco 280759 Manuel utilisateur
Vanco
Vanco Evolution EVSW4K41 Manuel utilisateur
Vanco
Vanco Evolution EVSW1061 Manuel utilisateur
Vanco
Vanco Evolution EVSW1040 Manuel utilisateur
Vanco
Vanco Evolution EVSW41KVM Manuel utilisateur
Vanco
Vanco HDMISW41 Instructions d'installation
