Vanco HDWIRKIT Manuel utilisateur

HDMI® WIRELESS

EXTENDER/

RECEIVER

Vanco Part Number:

HDWIRKIT

HDWIR-RX

Technical Support

www.vanco1.com • [email protected] • 800-626-6445

www.vanco1.com 800-626-6445

1. Do not expose this unit to water, moisture,

or excessive humidity.

2. Do not install or place this unit in a built-in

cabinet, or other conned space without

adequate ventilation.

3. To prevent risk of electrical shock or re

hazard, due to overheating, do not obstruct

unit’s ventilation openings.

4. Do not install near any source of heat,

including other units that may produce heat.

5. Do not place unit near ames.

6. Only clean unit with a dry cloth.

7. Unplug unit during lightening storms, or

when not used for an extended period

of time. A surge protector is strongly

recommended.

8. Protect the power cord from being walked

on or pinched, particularly at the plugs.

9. Use unit only with accessories specied by

the manufacturer.

10. Refer all servicing to qualied personnel.

CAUTION

HDMI is a very complex technology requiring continuous authentication of the signal and the same

video resolution and audio settings on all electronic equipment in the system. When there are multiple

sources and displays, the video resolution and audio setting on all connected units must be adjusted

to correspond with that of the display having the lowest video and audio capability.

WARNING

DEAR CUSTOMER

Thank you for purchasing this product.

For optimum performance and safety, please

read these instructions carefully before

connecting, operating or adjusting this product.

Please keep this manual for future reference.

This product is 100% inspected and tested in the United States

to verify HDMI performance parameters.

www.vanco1.com 800-626-6445 3

FEATURES

The Vanco HDWIRKIT/RX extends HDMI signals wirelessly from a source to a display up to

131ft/40m using wireless technology. There are no cables that are required between the

transmitter and receiver which makes for a clean and easy installation, especially where cabling

is difcult or impossible to run. Using a 5GHz operation frequency, the HDWIRKIT Transmitter

and Receiver do not require line of site transmission, the wireless signal will travel through most

obstacles with no issues. Out of the box, the HDWIRKIT works as a point to point conguration,

however also supports having multiple sets on the same site (up to 10) and one to multiple (1 TX

to up to 4 RX) displays using HDWIR-RX receivers (sold separately). A great solution for splitting

a single source signal wirelessly. Also features dual band IR call back to control the source from

any display location connected. With the ability of sending HDMI signals wirelessly, whether point

to point or splitting to multiple displays, the HDWIRKIT and optional HDWIR-RX are easy solutions

where running cable is an issue.

HDMI® WIRELESS EXTENDER/RECEIVER

Part # HDWIRKIT (transmitter and receiver)

Part # HDWIR-RX (receiver only)

• Extends HDMI signals wirelessly up to 131ft/40m

• Transmits up to 1080p HD video and audio

• Kit includes both Transmitter and Receiver for point to point application

• Able to split wireless HDMI signals to up to 4 displays (additional HDWIR-RX receivers sold separately)

• Multiple kits able to be installed in one application without interference

• Perfect solution where cabling cannot be run such as a mantle or outdoor application

• IR pass-through to control source from display location wirelessly

• Wireless 5 GHz frequency

• No line of sight installation required, wireless signal will pass through most obstacles

• Easy manual front panel or IR setup for multiple units

• Dimensions: 5.25” W x 0.75” H x 3” D

www.vanco1.com 800-626-6445

PACKAGE CONTENTS

Before attempting to use this unit, please check the packaging and make sure the following items are

contained in the shipping carton:

• Wireless Transmitter (HDWIRKIT only)

• Wireless Receiver

• 5V/2A Power Supply

• IR Blaster (TX)

• IR Receiver (RX)

• IR Remote Control

• Product Manual

SPECIFICATIONS

Power Supply ............................................................ Voltage/Current: DC5V/2A; Power consumption

TX<7W, RX< 5W

HDMI Compliance ...................................................... HDMI 1.3

HDCP Compliance...................................................... HDCP 1.2

HDMI Resolutions Supported ...................................... 480i@60Hz, 480p@60Hz, 576i@50Hz,

576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz

Supports Audio Formats............................................. L/R stereo audio

Maximum Transfer Rate ............................................. 10.2 Gbps

Input and Output TMDS signal..................................... 0.5 ~ 1.5Vp-p(TMDS)

Input and Output DDC signal ....................................... 5Vp-p(TTL)

IR Remote Control ..................................................... Supports IR callback (RX->TX); 20-60KHz frequency

Transmission Method ................................................. 5G Wireless Transmission

Latency..................................................................... 120ms

Electrostatic Protection.............................................. 1a Contact discharge level 3; 1b Air discharge level

3; Standard: IEC61000-4-2

Operating Temperature............................................... 32~122 Fahrenheit

Storage Temperature ................................................. 14~158 Fahrenheit

Humidity (no condensation) ......................................... 0~90%

Dimensions ............................................................... 5.25” W x 0.75” H x 3” D (each unit)

Material.................................................................... Iron alloy material + crystal panel

Processing Technology................................................ Sandblasting

Color ........................................................................ Black

Weight ..................................................................... TX: 0.68 lbs; RX: 0.68 lbs

www.vanco1.com 800-626-6445 5

PANEL DESCRIPTIONS

1. Antennas

2. RF Channels (Selectable 0-9 to “marry” to Receiving unit; or to split to multiple HDWIR-RX receivers)

3. Channel Toggle Switch (will change RF Channels 0-9 sequentially)

4. IR Sensor (for included remote to change to RF channels remotely)

5. Reset Button

6. DC 5V Power Supply Port

7. HDMI INPUT (Connect to an HDMI source)

8. Signal Status Indicator (Solid Green for successful signal when connected to source)

9. Syncing Status (Blinking Green when connected to Receiving unit; Solid Green will appear if no connection

to Receiver)

10. HDMI OUT (Loop-out, able to use as a splitter to connect to a local display such as a control room display)

11. IR OUT (Connect included IR Blaster (TX) and place near or at source for IR control)

TRANSMITTER

www.vanco1.com 800-626-6445

PANEL DESCRIPTIONS

RECEIVER

1. Antennas

2. RF Channels (Selectable 0-9 to “marry” to Transmitting unit; other Receivers can be set to the same RF

channel to split signal)

3. Channel Toggle Switch (will change RF Channels 0-9 sequentially)

4. IR Sensor (for included remote to change to RF channels remotely)

5. Reset Button

6. DC 5V Power Supply Port

7. Signal Status Indicator (Solid Green for successful signal when connected to source)

8. Syncing Status (Blinking Green when connected to Receiving unit; Solid Green will appear if no connection

to Receiver)

9. HDMI OUTPUT (Connect to an HDMI display)

10. IR IN (Connect included IR Receiver (RX) and place near or at display for IR control)

67810

235

www.vanco1.com 800-626-6445 7

CONNECT AND OPERATE

1. Connect HDMI cable from a source into the HDMI IN port of the TRANSMITTER

2. OPTIONAL: Connect the provided IR BLASTER into the IR OUT port of the TRANSMITTER

3. OPTIONAL: Connect HDMI Cable to the HDMI OUT port to loop-out to a local display such as a control

room display

4. Connect an HDMI cable from the HDMI OUT port of the RECEIVER to a display or sink device

5. OPTIONAL: Connect the provided IR RECEIVER into the IR IN port of the RECEIVER

6. Connect both power supplies to the TRANSMITTER and RECEIVER using the provided power supplies,

TRANSMITTER rst, followed by RECEIVER

7. Using the manual toggle buttons on the units or the provided IR remote control, select any available

channel; the TRANSMITTER and RECEIVER MUST be on the same channel (if using multiple kits, set each

kit to different channels to avoid signal interference)

NOTE: If there is no signal on startup, press the RESET button on the TX and/or RX.

NOTE: Transmission distance may differ based on certain environmental factors such as other wireless signals

that can interfere with transmission. Solid core walls, brick, or glass can signicantly shorten the range at

higher resolutions.

www.vanco1.com 800-626-6445

IR PASS-THROUGH

The IR system allows you to control the source that is connected to the extender unit, from the display. There

are two important things to note when setting up the IR system:

1. The IR Receiver (IR RX) is always what you point your remote at to send an IR signal. This pigtail is

placed at the display for controlling the source.

2. The IR Blaster (IR TX) is what sends the IR signal to what you are intending to control. This pigtail is

placed at the source; either pointed at the source, or placed on the front panel of the source (see below

for placement tips).

IR BLASTER (TX)

To control the source: plug IR Blaster into IR OUT port of TRANSMITTER; place blaster in front of the IR eye of

the source.

Note: Placement of the IR Blaster is important and can result in the IR system not working if improperly

placed.

• First, locate the IR eye or window on the source

• If placing the IR blaster right on the front panel of the source, do not stick right on top of the IR eye or

IR window. The IR signal cannot travel through the double-sided tape on the Blaster. Instead place the

blaster on either side, or on the top or bottom of the IR eye or window, with the tip of the blaster facing

the IR eye or window. See below for illustration of where IR signal shoots from on IR Blaster:

IR BLASTER (TX)

www.vanco1.com 800-626-6445 9

IR RECEIVER (RX)

• To control the source: Plug IR Receiver into IR IN port of RECEIVER; place receiver at or near display.

• Note: Due to possible differences in 3rd party IR cables, please use the IR cables that came with the

product.

IR RECEIVER (RX)

www.vanco1.com 800-626-6445

SAFETY AND NOTICE

The HDWIRKIT/HDWIR-RX has been tested for conformance to safety regulations and requirements, and has

been certied for international use. However, like all electronic equipment, the HDWIRKIT/HDWIR-RX should

be used with care. Please read and follow the safety instructions to protect yourself from possible injury and

to minimize the risk of damage to the unit.

• Follow all instructions and warnings marked on this unit.

• Do not attempt to service this unit yourself, except where explained in this manual.

• Provide proper ventilation and air circulation and do not use near water.

• Keep objects that might damage the device and assure that the placement of this unit is on a stable surface.

• Use only the power adapter and power cords and connection cables designed for this unit.

• Do not use liquid or aerosol cleaners to clean this unit.

• Always unplug the power to the device before cleaning.

TROUBLE-SHOOTING

1. If the display has “waiting for connection” on the bottom right hand corner:

Check to see if the power supply of the transmitter and receiver are well connected and that the power

indicator lights are ON

2. If the display states, “Please check the TX input signal...”

First check to see if there input is properly connected and powered on. Next try to connect the signal source

directly to the display device to see if there is a signal output from the source device or change the signal

source.

3. If the display is not stable:

• Try moving the position of the transmitter and receiver and make sure the range of the device has not

been exceeded.

• Hit the “RESET” button on the RX rst, followed by the TX. Please allow time to sink before trying the TX

RESET button

• Remove power and HDMI form both sides, reconnect the HDMI cables FIRST, then power after

• Look to remove other wireless signal that may be disrupting the transmission

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Vanco Extenseur

Vanco

Vanco EVOLUTION EVWP3000 Manuel utilisateur

Vanco

Vanco 280501 Manuel utilisateur

Vanco

Vanco EVOLUTION EVEXUSB2 Manuel utilisateur

Vanco

Vanco HDBaseT HDBT4K50 Manuel utilisateur

Vanco

Vanco EVEX2003 Manuel utilisateur

Vanco

Vanco 280547 Manuel utilisateur

Vanco

Vanco Evolution HDBASET EVEX2002 Manuel utilisateur

Vanco

Vanco HD4KEX30 Manuel utilisateur

Vanco

Vanco Evolution EVWP2006 Manuel utilisateur

Vanco

Vanco Evolution EV4K2006 Manuel utilisateur

Vanco

Vanco Evolution EVEX2007 Manuel utilisateur

Vanco

Vanco EVEX2004 Manuel utilisateur

Vanco

Vanco Evolution EVEXKVM3 Manuel utilisateur

Vanco

Vanco Evolution EVMX44VW Manuel utilisateur

Vanco

Vanco EVEXVGAHD Manuel utilisateur

Vanco

Vanco 280544 Manuel utilisateur

Vanco

Vanco Evolution EVEXHDB3 Manuel utilisateur

Vanco

Vanco EVEXFBRK1 Manuel utilisateur

Vanco

Vanco 280621 Manuel utilisateur

Vanco

Vanco VPW-280577 Manuel utilisateur

Vanco

Vanco Evolution Manuel utilisateur

Vanco

Vanco 280567 Manuel utilisateur

Vanco

Vanco HDEX60 Manuel utilisateur

Vanco

Vanco VPW-280572 Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur