Vanco Evolution EVEX2005 Manuel utilisateur

HDMI

Transmitter

Connect Power Supply

QUICK INSTALL GUIDE

Factory Setting EDID & EQ Dial - From Factory Settings are as Follows:

1. Transmitter Factory Default Setting is Set at EDID = “0” Supporting: HD (1080p@60) (1080p@30) (1080p@24)

(1080i@60)(720p@60) - 24bit 2D video & 7.1ch audio

2. Receiver E.Q. Dial Setting = “4” Supporting: 20M-25Meters (66 ft to 82 ft)

3. Proceed to Connect & Operate with Normal Installation (see reverse side). If there is no handshake or signal, Adjust EQ

Gain Control according to your CAT5e/CAT6 Cabling: from Minimum Dial Setting “0” to Maximum Setting “7”

Manual EDID Learning Mode

1. Set Learning (Copy) EDID Mode on the Transmitter (TX) unit = “7”

2. (SEE DRAWING) FIRST: Connect Transmitter (TX) unit directly to the Flat Panel Display using a HDMI cable. SECOND:

Connect the 5VDC Power Adapter. The “yellow” Status LED light must blink once for Learning (Copy) EDID to be

Successful. Now you can disconnect Transmitter (TX) from Flat Panel Display.

Note - Do not connect Receiver ( RX) unit during Learning (Copy) EDID Mode

If experiencing No Picture, Picture Flashing, or Drop-Signal then proceed to Manual Learning EDID Mode

NOTE - Recommended EDID setting for most cable and satellite set top boxes is

EDID “4” or “5”. If no signal is displayed after manual EDID learning mode, adjust

to another EDID setting by doing the following:

1. Unplug the 5VDC power supply and HDMI cable from the Transmitter (TX)

2. Adjust EDID to desired setting

3. Reconnect HDMI cable from the source into the Transmitter (TX)

4. Reconnect 5VDC power supply to the Transmitter (TX)

3. Change Transmitter back to Factory Default Setting EDID = “0”

4. Proceed to Connect & Operate with Normal Installation (see reverse side). Wait for Sync

Lights (on Transmitter & Receiver) to Stop Flashing

5. If no Picture or Signal is on the Flat Panel Display then Power OFF (both Units) & Power

ON (both Units). Simply remove the 5VDC Power supplies & reconnect

BluRay® Player

HDTV

HDMI HDMI

IR Transmitter IR Receiver

IR Transmitter

Receiver

HDMI over Cat5e/6

Transmitter Receiver

Back

Front

Back

Front

1. Connect a source such as a Blu-Ray Player, game

console, A/V Receiver, Cable or Satellite Receiver, etc.

to the HDMI input on the Transmitting unit.

2. Connect a display such as an HDTV or HD Projector to

the HDMI output on the Receiving unit.

3. Connect a single Category 5e/6 up to 131ft/40m to

the output of the Transmitting unit, and the other end to

the input of the Receiving unit.

4. For power, plug both the Transmitting unit and Receiving

unit with the included power supplies.

CONNECT AND OPERATE

0 - EDID Full-HD (1080p@60) (1080p@30) (1080p@24)

(1080i@60 (720p@60) - 24bit 2D video & 7.1ch audio

1 - EDID Full-HD(1080p@60) - 24bit 2D video & 2ch audio

2 - EDID Full-HD(1080p@60) - 24bit 3D video & 7.1ch audio

3 - EDID Full-HD(1080p@60) - 24bit 3D video & 2ch audio

4 - EDID HD(1080p@30)(1080i@60)(720p@60) - 24bit 2D video

& 7.1ch audio

5 - EDID HD(1080p@30)(1080i@60)(720p@60) - 24bit 2D video

& 2ch audio

6 - EDID Full-HD(1080p@60) - 36bit 2D video & 7.1ch audio

7 - Auto EDID learning/ Manual EDID learning mode

EQ ROTARY DIAL

If you see ickering or blinking image on the display, adjust the EQ rotary

switch to improve the cable skew. MAX stands for the strongest HDMI

signal level for the longest possible transmission length while MIN stands

for the weakest HDMI signal level for short transmission length. Adjust the

signal level from MIN to MAX until desired video quality is displayed.

Recommended EQ settings

LENGTH

Position Cable Length

0 (MIN)-2 under 15m (49.5ft)

3-5 15-30m (49.5 ft - 99ft)

6-7 (MAX) 30-40m (99ft - 132ft)

EDID SETTINGS

Autres manuels pour Evolution EVEX2005

Table des matières

Autres manuels Vanco Extenseur

Vanco

Vanco HDEXWIR Manuel utilisateur

Vanco

Vanco HDEX60 Manuel utilisateur

Vanco

Vanco Evolution EVEXKVM3 Manuel utilisateur

Vanco

Vanco IR-EXPKIT Manuel utilisateur

Vanco

Vanco 280544 Manuel utilisateur

Vanco

Vanco 280501 Manuel utilisateur

Vanco

Vanco 280502 Manuel utilisateur

Vanco

Vanco Evolution EVWP2006 Manuel utilisateur

Vanco

Vanco EVEXFBRK1 Manuel utilisateur

Vanco

Vanco EVEX2003 Manuel utilisateur

Vanco

Vanco EVOLUTION EV4K2004 Manuel d'instructions

Vanco

Vanco Evolution EVEX2330 Manuel utilisateur

Vanco

Vanco Evolution EVEXHDB1 Manuel utilisateur

Vanco

Vanco 280547 Manuel utilisateur

Vanco

Vanco HDBaseT HDBT4K50 Manuel utilisateur

Vanco

Vanco PulseAudio PAEXARC1 Manuel utilisateur

Vanco

Vanco AMP202 Manuel utilisateur

Vanco

Vanco Evolution EV4KWHDMI Manuel utilisateur

Vanco

Vanco EVOLUTION EVEXUSB2 Manuel utilisateur

Vanco

Vanco Evolution EVMX44VW Manuel utilisateur

Vanco

Vanco Evolution EVEX2005 Manuel utilisateur

Vanco

Vanco 280567 Manuel utilisateur

Vanco

Vanco HDWIRKIT Manuel utilisateur

Vanco

Vanco Evolution EV4K2006 Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur