Valore V-VMS603 Manuel utilisateur
Valore WiFi Action Camera (V-VMS603)
Thank you for purchasing the Valore WiFi Action Camera (V-VMS7603)
Never miss another moment with the Valore WiFi action camera. Switch freely between Car
DVR and sports action mode with this multipurpose camera and capture more of your
surroundings in a single shot with 170° ultra wide-angle lens.
Important: Please read the user manual thoroughly before using your action camera.
Specifications: Package Contents:
• Image sensor: 10 Mega Pixels CMOS • WiFi action camera
• LCD: 1.5 inch • Waterproof housing
• Lens: 170° ultra wide-angle • Bicycle holder
• Resolution: 1920 x 1080 at 30fps • Base x7
1280 x 720 at 60fps • Lens cloth
1280 x 720 at 30fps • USB cable
• Input: DC5V/1A • Helmet Base
• WiFi distance: 10m • Bandages
• Battery type: Built-in 3.7V Lithium battery 700mAh • Suction cup
• Video format: MOV • Car charger
• Video codec: H.264 • Tethers
• Photo Format: JPEG
• Dimension (L x W x D):69 x 39 x 38mm
• Weight: 70g (with waterproof case 137g)
UNDERSTANDING THE PRODUCT
①ON / OFF / Mode switch
②REC / OK / Wi-Fi
12
3
4
5
6
7
8
WIFI
SOS
③Up (Zoom in)/ IR Light
④ Menu / Back
⑤ Down (Zoom Out)
⑥ REC / OK / Wi-Fi
⑦ Playback
⑧ Microphone / Video Lock
⑨ Reset
⑩ AV Out
11 Micro USB Port
Micro SD Card Slot
911
10
12
12
MOUNTING THE CAMERA
1) Please make sure that you are following the regulations and laws set by your Country or
states DMV (Department of Motor Vehicles) prior to mounting your camera. This will avoid
any accidents and traffic violations that can occur if the camera is mounted in a location that
is prohibited by law.
2) Using the suction cup and rotating bracket, mount the Wi-Fi Action Camera to the inside of
your vehicles windshield (use the adjustment knob to loosen and tighten the Wi-Fi Action
Camera as needed).
NOTE: The Wi-Fi Action Camera can also be used to record both exterior and interior (front
and rear) of your vehicle. For interior recording, simply follow the steps above and rotate the
camera so that the lens is facing the inside of your vehicle.
INSERT THE SD CARD
Insert your micro SD card into the Wi-Fi Action Camera’s micro SD slot. Make sure that you
insert the in the correct direction as shown. The SD card will make a clicking sound, indicating
it has been locked into the Carcam.
CONNECT THE POWER CABLE
1) Connect the car chargers cable into the Wi-Fi Action Camera’s power socket located on
the bottom side of the Carcam.
WIFI
SOS
2) Depending on where you’ve chosen to mount the Wi-Fi Action Camera, run the power
cable around the trim of your vehicle so that it will not obstruct your view while driving.
3) Insert the car charger into your vehicles cigarette lighter port as shown. A red light on the
car charger will light up, indicating it is connected.
TURNING THE CAMERA ON
The two ways in turning on your Wi-Fi Action Camera
1) Start your vehicle and the Wi-Fi Action Camera will automatically turn on and
begin recording.
2) Long press the power button manually to turn on the Wi-Fi Action Camera.
NOTE: The Wi-Fi Action Camera will automatically turn on/off whenever your vehicle turns
on/ off, respectively.
LIGHT INDICATORS
Battery Charging Light (Red) Power Light (Blue)
On
On Battery is currently
charging (Red)
On
Power is on (Blue) Off
Wi-Fi Action Camera
battery is
currently charing
(Red)
On
Off
Power is off
(No Blue Light)
Battery is fully
charged
(No Red Light)
Power is on
(Blue)
USED AS ACTION CAMERA
A Quick Introduction of how to attach your camera to helmets, gear and equipment.
NOTE : Please switch to Sports Mode by pressing On/Off/Switch button before putting into
the waterproof case.
SET DATE & TIME
1. Turn on your Wi-Fi Action Camera
• Press and hold the Power button until the “Welcome” screen appears
2. Press the Menu button twice to get to “Setup” menu
3. Select the Date&Time
• Press the “Down” button until Date&Time option is highlighted
• Press the “OK” button
4. Change the Date&Time
• Use the “Up” and “Down” buttons to change the date and the time
• Use the “ON/OFF/MODE SWITCH” button to go to next , and use the “OK” to confirm the
change.
FORMAT YOUR SD CARD
1. Turn on your Wi-Fi Action Camera
• Press and hold the Power button until the “Welcome” screen appears
2. Press the Menu button twice until the “Setup” settings appears on the screen
3. Select the Format option
• Press the “Down” button until “Format” option is highlighted
4. Confirm Formatting
• Press “OK” to confirm your SD Card to be formatted
CHANGE TO DEFAULT SETTINGS
1. Turn on your Wi-Fi Action Camera
• Press and hold the Power button until the “Welcome” screen appears
2. Press the Menu button twice until the “Setup” settings appears on the screen
3. Select the “System” option
• Press the “Down” button until “System” option is highlighted ,and press OK .
4. Select the “Default Settings” option
• Press the “Down” button until “Default Settings” option is highlighted
5. Confirm “Default Setting”
• Press “OK” to confirm your Carcam will switch back to its default settings
WIFI
SOS
UP/ZOOM IN
The UP/ZOOM IN button is used to navigate through out the menu and make setting
selections. It can also Zoom-In up to 2x its original distance while in video or photo mode.
（Note：Long press this button can enable/ disable the LED sensor when recording. ）
MENU/BACK
The MENU button allows access your Wi-Fi Action Camera menu settings. Pressing the
Menu button again will access to Setup settings. While in the Car / Sports Video mode, you
may access the Car / Sports Video and Setup settings. While in Photo mode, you may access
the Photo and Setup settings. While in Playback mode, you may access the Playback and
System settings.
DOWN/ZOOM OUT
The DOWN/ZOOM OUT button is used to navigate through out the menu and make setting
selections. It is also used to Zoom-out while in video or photo mode.
REC/OK/ Wi-Fi
The REC/OK/Wi-Fi button is used to start and stop manual recording while in Video mode. It
is also used to take pictures while in Photo mode. It can be used to make setting changes
and select which event to view during playback. Long press this button to activate the Wi-Fi
connection, Short press this button (when Wi-Fi is connected) to switch off Wi-Fi.
PLAYBACK
The PLAYBACK button is used to switch to Playback and view the video and photos been
recorded. In Car/Sports/Photo Mode settings, press this button to enter Setup Settings.
Up / Zoom In
Menu / Back
Down / Zoom Out
REC / OK / Wi-Fi
Playback
MIC / Lock
MIC/LOCK
The MIC/LOCK button is used to switch on/off the audio record (long press). This function
also locks the current video recording on your Wi-Fi Action Camera. By locking the video file,
it will prevent the file from being manually deleted.
POWER / MODE
The POWER/MODE button is used to switch between Car mode, Photo and Sports mode , it
also used to manually turn the Wi-Fi Action Camera on or off when needed(long press), but in
most cases the Wi-Fi Action Camera will automatically turn itself on and off whenever the
vehicle does.
SETTINGS
The Wi-Fi Action Camera’s settings are divided into 5 categories: Car Mode, Photo Mode,
Sports Mode, Playback settings, and Setup settings.
NOTE: The “Setup” settings can be accessed from The Car Video, Photo and Sports Video
settings.
CAR MODE SETTINGS
The Video configuration menu consists of settings and options that are used to configure the
Wi-Fi Action Camera’s video recording settings. In the Car Video mode, press the “Menu”
button to open up the Video configuration menu.
The Video settings consist of the following configuration options.
• Resolution – Video resolution configuration.
• Video Quality – Video quality configuration .
• Loop Recording – Overwrite configuration.
• Exposure – Adjust the amount of light that will affect your image sensor.
• Motion Detection – Enables/Disables motion detection recording.
• G-Sensor – G-force sensor configuration
• Parking Mode – Enable captures Hit and Run even when vehicle turns off .
• Date Stamp – Enables/Disables date stamp on recorded events.
RESOLUTION
The Wi-Fi Action Camera supports various video resolutions that you can select from. The
higher the resolution, the better your video quality and the bigger the video size will be.
Use the UP/DOWN keys to scroll through the options. Press the REC/OK button to select
your desired settings. The available options include:
• 1080HD @30fps (default)
• 720P @30fps
• 720P @60fps
VIDEO QUALITY
The Wi-Fi Action Camera supports various video quality that you can select from. The higher
the quality, the better your video quality will be.
Use the UP/DOWN keys to scroll through the options. Press the REC/OK button to select
your desired settings.
The available options include:
• Super Fine (default)
• Fine
• Normal
LOOP RECORDING
The loop recording option serves as two features: “Overwrite”&“Segment Length”. The
overwrite feature allows the DVR to delete previously recorded events in increments when the
SD card becomes full. The segment length feature is the length each recorded event can be
before generating a new file. Use the UP/DOWN keys to scroll through the options. Press the
REC/OK button to select your desired settings.
The available options include:
• Off – Disables overwrite and enables the default 24 hour segment recording.
NOTE: Setting this feature to off will create on long video which will stop recording as soon as
the file exceeds the memory cards capacity.
• 1 Minutes– Enables the DVR to record/overwrite in 1 minute increments
• 3 Minutes (default)– Enables the DVR to record/overwrite in 3 minute increments
• 5 Minutes – Enables the DVR to record/overwrite in 5 minute increments
EXPOSURE
The exposure option lets you select the numeric exposure value for your video recording. The
exposure feature consists of the following options:
+0.0 (defaut)
-2/3
-1/3
-1.0
-4/3
-5/3
+2.0
+4/3
+5/3
+1.0
+2/3
+1/3
-2.0
MOTION DETECTION
The motion detection option is used to enable/disable motion detection recording. While the
Wi-Fi Action Camera is on, and is on standby, any movement in front of it will trigger a
recording. The Motion Detection feature consists of the following options:
• Off/Disable(default)
• On/Enable
NOTE: Make sure the “Auto Power Off” function is set to “Off” to let the Wi-Fi Action Camera
stay on during standby mode. When motion detection is active or turned ON, the G sensing
will be deactivated. Please make sure motion detection is turned OFF for 2G and 4G sensor
to function properly.
DATE STAMP
The date stamp option is used to enable/disable the date & time stamp from being displayed
on playback videos. The date stamp feature consists of the following options:
• Off/Disable
• On/Enable (default)
G-SENSOR
The G-Sensor option is used to enable/disable the Wi-Fi Action Camera’s G-force/impact
sensor which will lock the previous and current file from being deleted by the overwrite
feature. The G-force acts as a sensor for the Wi-Fi Action Camera to secure any video files
recorded in the event that the vehicle gets hit. Any force that is acted upon the vehicle will
result in locking the current recording video file.
NOTE: Formatting the SD card will result in erasing all files, including the locked video files.
The G-Sensor feature consists of the following options:
• Off/Disable
• 2G (default)- Represents 9.8m/s2 of force (passenger car turning on a corner)
• 4G- Represents 19.62m/s2 of force (bump on the road)
• 8G- Represents 39.2m/s2 of force (car collision)
PARKING MODE
Parking protection functionality offers peace-of-mind while you’re away from your vehicle.
From collisions with other drivers who may bump into your vehicle and leave the scene. Any
force that is acted upon the vehicle will activate the Wi-Fi Action Camera to switch on, record
and lock the segment. Parking Mode feature consists of the following options:
Table des matières
Autres manuels Valore Caméra d'action
