Valor tpms Manuel utilisateur
TPMS - Setup Guide
Pro V2.2
Truck
1-800-568-9188
4320 Harvester Rd., Floor 2
Burlington, ON, L7L 5S4, Canada
SETUP GUIDE – TPMS
2
Table of Contents
Programming the CANbus Transceiver using the SmarTool
Main Menu.................................................................................................................................................................4
SmarTool Setup .........................................................................................................................................................5
System Setup ...........................................................................................................................................................6
Step 1: Read CANbus ID........................................................................................................................................... 7
Step 1.1.....................................................................................................................................................................7
Step 1.2 ....................................................................................................................................................................8
Step 2: Read Sensor ID/Set Positions .......................................................................................................................9
Step 2.1...................................................................................................................................................................10
Step 3: Uploading to Valor CANbus Memory............................................................................................................ 11
Step 3.1...................................................................................................................................................................12
Step 4: Program Valor CANbus Transceiver ............................................................................................................ 13
Step 4.1...................................................................................................................................................................14
Step 4.2...................................................................................................................................................................14
Step5:ConrmProgramming.................................................................................................................................. 15
Step 6: Baseline Setup ............................................................................................................................................16
Step 6.1...................................................................................................................................................................17
SETUP GUIDE – TPMS
3
Intro: Programming the CANbus Transceiver using the SmarTool
1. These instructions apply only to Valor CANbus
Transceivers (Figure 1) that require a Valor SmarTool
for sensor programming.
2. The SmarTool must be updated to the latest software
version (Pro 2.2 or higher). To check the software
version on your SmarTool simply press the on/off
button. The firmware version of the device will display
on screen Figure 1A.
Figure 1
Figure 1A
Pro V2.2
Truck
SETUP GUIDE – TPMS
4
Main Menu
1. Once the SmarTool is turned on, the Start menu should
be the same as that shown in Figure 2.
2. This is the home screen and it lists 7 possible
selections as you scroll down the menu using the up/
down arrow keys.
‣Sensor 1/7
‣Vehicle ID 2/7
‣ID Learning 3/7
‣Check ID 4/7
‣Baseline 5/7
‣Download 6/7
‣System Set 7/7
Sensor 1/7
Vehicle ID
ID Learning
Check ID
Figure 2
SETUP GUIDE – TPMS
5
SmarTool Setup
These instructions are for rst use only to setup the
SmarTool:
1. In main menu scroll to “System Set” (Item 7/7)
2. Press ENTER
3. Set up units of measure, select “Set Unit” (C/PSI)
4. Press ENTER
5. Default settings are in BAR/Celsius (BC), to switch to
PSI/Fahrenheit (PF) use the up/down arrow
(Figure 3)
6. Press ENTER to select (unit will beep to confirm)
7. Press ESC to return to the Setting screen
8. To set up the number of axles, select “Set Axle”
(Figure 4)
9. Press ENTER
10. Use up down arrow keys to select number of axles
11. Press ENTER once (note: Screen doesn’t change)
12. Press ESC twice to return to Main Menu
*Note: If programming TempTrac, please refer to the
TempTrac Setup Guide.
Figure 4
Figure 3
Setting
Set Unit
Set Axle
Current Unit: PF
Want to Set: BC
SETUP GUIDE – TPMS
6
System Setup
The system setup requires the following steps:
1. Read CANbus ID
2. Read Sensor ID/Set positions
3. Format Valor CANbus memory
4. Program Valor CANbus transceiver
5. Confirm programming
Turn to next page to begin Step 1.
Pro V2.2
Truck
Figure 5
SETUP GUIDE – TPMS
7
STEP 1
STEP 1 - Read CANbus ID
1. In Main menu scroll to “ID Learning” (item 3/7).
(Figure 6)
2. Press ENTER
STEP 1.1
1. In the “ID Learning” menu, select “Read ID.” (Figure 7)
2. Press ENTER
Figure 6
Sensor 3/7
Vehicle ID
ID Learning
Check ID
Figure 7
ID Learning
Read ID
Transmit
Clear ID
SETUP GUIDE – TPMS
8
STEP 1
STEP 1.2
1. Position the SmarTool directly over the Valor CANbus
transceiver.
2. With the cursor arrow positioned next to “Vehicle
ID:” (Figure 8) turn the power to the Valor CANbus
transceiver OFF and back ON. (I.e. vehicle ignition or
power interrupt button on Valor harness (Figure 8A).
3. DO NOT PRESS THE ENTER BUTTON on the
SmarTool.
4. The Vehicle ID number will populate automatically.
(Figure 8B)
Figure 8
Vehic ID:______
1-A: ________
1-B: ________
1-C: ________
Figure 8B
Vehic ID: 0014BC
1-A: ________
1-B: ________
1-C: ________
Figure 8A
SETUP GUIDE – TPMS
9
STEP 2
STEP 2 - Read Sensor ID/Set Positions
1. Using the up/down arrow buttons, select the tire
position you want to program. Once the arrow
is in the selected position (Figure 9), go to the
corresponding tire on the vehicle.
Example: If programming 1–A to the left front tire,
position the SmarTool approx. 1 inch from the side
of the tire you wish to scan (sensors are normally
installed near the valve stem).
2. Press ENTER
3. A series of zeros will scroll across the SmarTool
indicating a search for sensor. When it locates the
sensor, the SmarTool will beep once. (Figure 10)
Figure 9
Vehic ID: 0014BC
1-A: ________
1-B: ________
1-C: ________
Figure 10
OOOOOOOOOO
SETUP GUIDE – TPMS
10
STEP 2
STEP 2.1
1. Once it locates the sensor, the SmarTool will display
the ID number in the tire position field selected by the
operator.
2. If performing a complete tire installation, be sure to
repeat this step for each tire before moving to the next
step.
3. Once all Sensor ID numbers (tires) have been
scanned/ loaded, press ESC on the SmarTool and
return to the “ID Learning” menu. Return to the
vehicle’s cab.
4. *Note: When programming a Valor CANbus
transceiver for an axle with only two wheel positions
(tires) program the sensor ID numbers in positions – A
for left side and B for the right side. (Figure 11)
By positioning the sensors this way the graphical
display on the Ametek gauge will appear with 2 wheel
positions on the axle, not 4. For axles with 4 wheel
position (tires), program the sensor ID numbers as
normal: outside left A, inside left B, inside right C,
outside right D.
Figure 11
Vehic ID: 0014BC
1-A: 01015669
1-B: 01015559
1-C: ________
Table des matières
Autres manuels Valor Émetteur-récepteur
