UWT Nivotec NT 4600 Manuel utilisateur

Level monitoring system

NT 4600

Technical information / Instruction manual

page

Table of contents

Subject to technical change. We assume no liability for typing errors.

Page

Safety notes/ Technical support 2

------------------------------------------------------------------------------------------------------

Overview 3

------------------------------------------------------------------------------------------------------

Technical Data 4

------------------------------------------------------------------------------------------------------

Accessories 4

------------------------------------------------------------------------------------------------------

Electrical installation 5

------------------------------------------------------------------------------------------------------

Commissioning 10

------------------------------------------------------------------------------------------------------

Visualisation - Operation 11

Nivotec®1

NT 4600 gi010417

Level monitoring system

NT 4600

Technical information / Instruction manual

page

Safety notes / Technical support

Notes

• Installation, maintenance and commissioning must be carried out only by qualied technical personnel.

• The product must be used only in the manner outlined in this instruction manual.

Special attention must be paid to warnings and notes as follows:

WARNING

Relates to a caution symbol on the product and means, that a failure to observe the necessary

precautions can result in death, serious injury and/ or considerable material damage.

WARNING

Relates to a caution symbol on the product and means, that a failure to observe the necessary

precautions can result in death, serious injury and/or considerable material damage.

This symbol is used, when there is no corresponding caution symbol on the product.

A failure to observe the necessary precautions can result in considerable material damage.

CAUTION

Safety symbols

In manual and on

product Description

CAUTION: refer to related documents (manual) for details.

Earth (ground) Terminal

Protective Conductor Terminal

Technical support

Please contact your local supplier (see www.uwt.de for address). Otherwise you can contact:

UWT GmbH Tel. 0049 (0)831 57123-0

Westendstr. 5 Fax. 0049 (0)831 76879

87488 Betzigau [email protected]

Germany www.uwt.de

Nivotec®

NT 4600

gi010417

Level monitoring system

NT 4600

Technical information / Instruction manual

page

Overview

Level monitoring and visualisation via touch panel

- Standardized system up to 15 silos

- Visualisation and operation via 7" touch panel (coloured, 800 x 480 pixel)

- Software language german or english

- Password protected

- Data in percentage, height, volume or weight

- Trend display, data storage

- Evaluation of the analogue 4-20 mA signals of any sensors, as well as Modbus RTU of the UWT-systems

- Different input signals within the same system is possible

- Implementation of full detectors

- Fill control via full alarm signal (Buzzer)

NT 4600 Basis unit

The heart of the NT 4600 is a touch panel, which runs

the visualisation software. All ll level control and display

functions can be operated via the touch panel. Access is

password protected. The electromechanical lead system can

be started by the visualisation software.

Integration of full detector

incl. alarm "silo full"

- Buzzer with reset button (supplied loose,

for outdoor mounting)

- One unit for all connected silos

- Alarm happens, if one of the silos gets full

- Reset of the alarm

- Provided for mounting directly on the silo

Modbus converter

- For connection of 4-20 mA/ 2-wire sensors and full detectors

- On each converter up to 4 sensors and 4 full detectors can

be connected

- Provided for mounting directly on the silo

NT 4600

Buzzer Reset

button

Modbus converter

e.g

NR 3000

Full detector

Modbus RTU

NB 3000/

NB 4000

Modbus RTU

4-20 mA

Full detector

Connection of

further Modbus

converters

Connection of

further

NB 3000/ NB 4000

Basis unit

Alarm "Silo full"

Nivotec®1

NT 4600 gi010417

Level monitoring system

NT 4600

Technical information / Instruction manual

page

Technical Data / Accessories

Technical data

Dimensions NT 4600, Modbus converter: 300 x 300 x 155 mm (W x H x D)

Dimensions

(Touch panel without

cabinet)

Touch panel 200 x 146 x 34 mm

Panel cutout 192 x 138 mm

Mounting NT 4600, Modbus converter: wall mounting

Material NT 4600, Modbus converter: steel plate

Ingress protection NT 4600, Modbus converter: IP65

Ambient temperature NT 4600: 0 .. +50°C

Modbusumsetzer: -25 .. +70°C

Power supply NT 4600, Modbus converter: 115 V or 230 V 50/ 60 Hz (integrated power converter 24 VDC)

NR 3000: supplied by Modbus converter

NB 3000/ 4000: 115 V or 230 V AC, connection is made on site

Full detector: Connection either on NB 3000/ NB 4000 resp. Modbus

converter.In this case the supply voltage must be equal to

NB 3000/ NB 4000 resp. Modbus converter. Alternative it is

possible to connect on site.

Power consumption NT 4600, Modbus converter: 20 VA

Connected level sensors: see documentation of the respective sensors

Signal output full detector Floating contact is required

Terminal box

Intermediate terminals for the wires leading to the silo (mounting e.g. on the silo frame).

Applicable for cables of level (Modbus or 4-20 mA), limit switch, buzzer, reset button

Technical data

Dimensions 200 x 300 x 120 mm (W x H x D), for wall mounting

Material steel plate

Ingress protection IP65

Ambient temperature -25 .. +60°C

Terminal blocks 15 pieces grey, 5 pieces blue, 5 pieces green/yellow; each terminal implements 3 cable inlets

2.5 mm2, mounted on top hat rail

Cable glands 6 pieces M20 x 1.5 2 pieces M25 x 1.5

Nivotec®

NT 4600

gi010417

Level monitoring system

NT 4600

Technical information / Instruction manual

page

Electrical installation

Handling In case of improper handling or handling malpractice, the electric safety of the device cannot be

guaranteed.

Installation regulations The local regulations or VDE 0100 (Regulations of German Electrotechnical Engineers) must be

observed.

Fuse Use a fuse as stated in the connection diagrams.

RCCB protection In case of a fault, the supply voltage must be automatically switched off by a RCCB protection switch

to protect against indirect contact with dangerous voltages.

Power supply switch A voltage disconnection switch must be provided near the device.

Wiring diagram The electrical connections are made in accordance with the wiring diagram.

Supply voltage Compare the supply voltage applied with the specications given on the name plate before switching

the device on.

Cable gland Make sure that the screwed cable gland safely seals the cable and that it is tight (danger of water

intrusion).

Cable glands that are not used have to be sealed with a blanking element.

Field wiring cables All eld wirings must have insulation suitable for at least 250 V AC. The temperature rating must be at

least 80°C (176°F).

Installation in Hazardous

Locations

The NT 4500 and the Mobus converter are not permitted for installation in Hazardous Areas. Observe

the valid regulations for wiring in Hazardous Areas, if the NB 3000/ NB 4000 is installed in Hazardous

Areas.

Safety Instructions

Modbus network

Modbus Master

NT 4500

Other used notations:

D0 = Rx-/Tx- = A

D1 = Rx+/Tx+ = B

Modbus converter or

NB 3000/ NB 4000

Modbus Slaves

General wiring of a Modbus network

Terminals D0 as well as D1 are

internally connected.

Termination Resistor

120 Ohm at the end of the

strand. It is present inside

each Modbus converter and

NB 3000/ NB 4000 and can

be switched in.

Modbus converter or

NB 3000/ NB 4000

Modbus converter or

NB 3000/ NB 4000

Note:

If required it is possible to split the Modbus network into two strands. Both strands are wired in parallel at the Modbus Master.

A termination resistor must be present at the end of each strand.

Nivotec®1

NT 4600 gi010417

Level monitoring system

NT 4600

Technical information / Instruction manual

page

Electrical installation

Cable recommendations for Modbus network

Shielded cable

Functionality up to 50 m

Manufacturer: Lapp, Type UNITRONIC LiYCY 2x 0.34, Art.no: 0034502

Twisted pair cable

Functionality up to 1,000 m

Manufacturer: Lapp, Type UNITRONIC BUS CAN 1x 2x 0.34, Art.no: 2170263

UV-protection hose with threaded hose coupling M20 x 1.5

UV protection for Modbus cable

Manufacturer: Flexa, Type Rohrex PA6, Art.no: 0233.202.012 and Type RQG1-M, Art.no: 5020.055.018

ATEX-protection hose with threaded hose coupling M20 x 1.5

For installation of Modbus cable in ATEX Zone 21

Manufacturer: PMA, Type ESX, Art.no: ESXT-12B.50 and Type END, Art.no: BEND-M202GT

NT 4600

Buzzer and reset button

(Alarm silo full)

Modbus

Fuse: max. 2 A

0.14 .. 2.5 mm2

(AWG 26 .. 14)

115 V or

230 V

50/ 60 Hz

Wiring of Touch panel

Only relevant if pos.1 A "Touch panel without control cabinet" was ordered

Sub-D female

on Touch panel

Modbus

24 V DC

±20%

350 mA

Fuse: max. 2 A

0.14 .. 2.5 mm2

(AWG 26 .. 14)

Nivotec®

NT 4600

gi010417

Level monitoring system

NT 4600

Technical information / Instruction manual

page

Electrical installation

NB 3000/ NB 4000

Full detector

Contact must be

closed in case of

full detection

Modbus

Fuse: max. 10 A

0.14 .. 2.5 mm2

(AWG 26 .. 14)

115 V or

230 V

50/ 60 Hz

Nivotec®1

NT 4600 gi010417

Level monitoring system

NT 4600

Technical information / Instruction manual

page

Setting: Biasing and Termination Resistor

For use of NB 3000/ NB 4000 units in a external Modbus

network, it is possible to set Biasing and Termination Resistor

on each unit as required.

Electrical installation

*factory provided

Biasing OFF* OFF ON ON

Termination

Resistor

OFF* ON OFF ON

*factory provided

Biasing OFF* OFF ON

Termination

Resistor

OFF* ON ON

Version with Jumper

Version with DIP switch

Biasing OFF* OFF ON ON

Termination

Resistor

OFF* ON OFF ON

NB 4000

NB 3000

DIP Switch position:

Side viewTop view

DIP Switch position:

Side viewTop view

Nivotec®

NT 4600

gi010417

Level monitoring system

NT 4600

Technical information / Instruction manual

page

Electrical installation

The stated wiring inside the Modbus converter is factory provided.

Termination Resistor needs

to be connected at the end

of the Modbus strand.

Power

supply

Modbus converter

115 V or

230 V

50/ 60 Hz

Fuse: max. 10 A

Terminals M-7002: 0.14 .. 1.5 mm2(AWG 26 .. 16)

Other terminals: 0.14 .. 2.5 mm2(AWG 26 .. 14)

Max. 4 sensors

4-20 mA/ 2-wire

Sensor

Max. 4 full detectors

Detector

Modbus

Modbus converter

Nivotec®1

NT 4600 gi010417

Level monitoring system

NT 4600

Technical information / Instruction manual

page

Commissioning

2. Check the wiring

Make sure that the Modbus network is wired, set the Modbus Termination Resistor (and for NB 3000 the Biasing), check that the

Ethernet connection is available (see "Electrical installation" from page 5 onwards).

3. Perform the basic settings for the visualisation

• Basic Settings - User (see page 13).

To do further settings, the userlevel must be set to Level 2.

• Basic Settings - System (see page 14).

4. Perform the settings of the silo data and of the connected sensors

With the following settings, the connected sensors are addressed via the visualisation and give a real measurement result. For this

settings the above mentioned synoptical table is helpful:

• Silo Settings (see page 16).

• Sensor Settings (see page 17 - 18).

Note: All units are presetted to 19200 Baud. Thus no setting is required.

1. Generation of a synoptical table

Commissioning is facilitated if an overview of the connected sensors is made in advance.

The table shows an example of a project with 10 silos and mixed conguration of Nivobob NB 3000 and NR 3000 radar

as well as implementation of full detectors:

Silo Sensor Modbus

Modbus converter*

Channel Terminal of

4-20 mA sensor

Terminal of

full detector

1NB 3000 3 n/ a n/ a n/ a

2NB 3000 4 n/ a n/ a n/ a

3NB 3000 5 n/ a n/ a n/ a

4NB 3000 6 n/ a n/ a n/ a

5 NR 3000 4-20 mA sensor 1 0 Vin0+ DI0

6 NR 3000 4-20 mA sensor 1 1 Vin1+ DI1

7 NR 3000 4-20 mA sensor 1 2 Vin2+ DI2

8 NR 3000 4-20 mA sensor 1 3 Vin3+ DI3

9 NR 3000 4-20 mA sensor 2 0 Vin0+ DI0

10 NR 3000 4-20 mA sensor 2 1 Vin1+ DI1

* see page 9 as well as 17 - 18 under "Input Signal"

Nivotec®

NT 4600

gi010417

Table des matières

Autres manuels UWT Instrument de mesure

UWT

UWT Nivotec NT 4500 Manuel utilisateur

UWT

UWT Nivobob NB 3000 Manuel utilisateur

UWT

UWT NivoRadar NR 7100 Series Manuel utilisateur

UWT

UWT Nivobob NB 3000 Manuel utilisateur

UWT

UWT NivoGuide 3100 Manuel utilisateur

UWT

UWT NG 8100 Manuel utilisateur

UWT

UWT NG 8100 Manuel utilisateur

UWT

UWT NivoRadar NR 4100 Series Manuel utilisateur

UWT

UWT NivoRadar NR 7100 Series Manuel utilisateur

UWT

UWT NivoRadar NR 7200 Series Manuel utilisateur

UWT

UWT Nivobob NB 4000 Manuel utilisateur

UWT

UWT NivoGuide 8100 Manuel utilisateur

UWT

UWT Nivo Radar NR 4000 Series Manuel utilisateur

UWT

UWT NivoRadar NR 7200 Series Manuel utilisateur

UWT

UWT NivoRadar NR 7000 Series Manuel utilisateur

UWT

UWT Rotonivo RN 3000 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur