US Robotics USR8001 Manuel utilisateur

Broadband Router

with USB Print Server

Quick Installation Guide

Guide d'installation rapide

Installationsanleitung

Guida per l'installazione rapida

Beknopteinstallatiegids

Guía breve de instalación

R24.0513.00

rev 4 03/2005

Quick Installation Guide..................................................................1

Guide d'installation rapide .............................................................11

Installationsanleitung .....................................................................21

Guida all'installazione rapida.........................................................31

Beknopte installatiegids.................................................................41

Guía breve de instalación...............................................................51

Quick Installation Guide

Package Contents:

• Broadband Router with USB Print Server

• 5.0 VDC power supply

• Ethernet cable

• Installation CD-ROM

•QuickInstallationGuide

Front View

Rear View

LEDS Action Function

WAN LINK Lighted WAN Ethernet signal detected

Blinking Sending or receiving WAN data

WAN 10/100 Lighted 100 Mbps WAN link is achieved

Off 10 Mbps WAN link is achieved

LAN LINK/ACT Lighted LAN Ethernet signal detected

Blinking Sending or receiving LAN data

LAN 10/100 Lighted 100 Mbps LAN link is achieved

Off 10 Mbps LAN link is achieved

Printer Lighted Link to printer is achieved

Blinking Sending or receiving printer data

System Blinking Router is functioning properly

Power Lighted Receiving power

Feature Function

5.0 VDC Power supply connection port

What You Need to Begin

• PC with an Ethernet adapter (NIC) installed

• A functioning Ethernet-based cable or DSL modem

an RS-232-based analogue or ISDN modem and an RS-232 cable

• Operating System installation CD-ROM

• Internet Explorer 5.0 or later

Netscape 7.0 or later

• Your CD-ROM drive letter (for example, D)

• Your router product number and serial number, located on the bottom label of the router. If

you ever need to call our Technical Support department, you will need this number to

receive assistance.

Router Installation

The U.S. Robotics Broadband Router with USB Print Server can easily be connected to any Ether-

net-based cable or DSL modem, or an RS-232 based analogue or ISDN modem.

Note: For the most updated information, visit: http://www.usr.com/support

You can also refer to the

User Guide

on the U.S. Robotics Installation CD-ROM for more

detailed information.

Step 1: Connect your modem to the router.

Cable or DSL Modem

1. Turn off your PC and your modem.

2. Locate the Ethernet cable that connects your modem to your PC’s Ethernet adapter, and dis-

connect it from your PC only: do not disconnect the cable from your modem.

RESET To reset the router to the factory default settings:

1. Unplug the power supply.

2. Press in and hold the RESET button.

3. While holding the RESET button, plug in the power supply.

4. Continue to hold the RESET button until the SYSTEM LED begins flashing.

COM To connect an analogue or ISDN modem

PRINTER To connect a USB printer to the LAN

LAN ports 1-4 To connect devices to the LAN

WAN RJ-45 port to connect a broadband modem

Product Number Serial Number

8001

Feature Function

3. Connect the free end of the Ethernet cable to the WAN port on the rear of the router.

Analogue or ISDN Modem

1. Turn off your PC and your modem.

2. Locate the serial cable that connects your modem to your PC’s serial port, and disconnect it

from the PC only. Do not disconnect the cable from your modem.

3. Connect the free end of the serial cable to the COM port on the rear of the router.

Step 2: Connect your router to your computer and power supply.

1. Connect one end of the supplied Ethernet cable to your PC’s Ethernet adapter.

2. Connect the other end to one of the router’s LAN ports.

LAN WAN

Modem

Router

LAN WAN

Router

Modem

LAN WAN

Cable or DSL

Router Modem

3. Turn on your modem.

4. Connect the supplied power cord to the 5.0 VDC port on the router.

Note to UK Users: Replace the plug on power adapter with the UK standard plug that is

supplied in your US Robotics package. Apply enough pressure to cause a click and firmly

seat the new plug.

5. Plug the power adapter into a standard power outlet.

6. Turn on your PC.

Step 3: Configure the basic connection settings.

Windows XP and Me users: If Universal Plug and Play launches, follow the on-screen

instructions instead of steps 1 and 2 below:

1. Launch a Web browser.

2. In the location or address line, type http://192.168.123.254 and press Enter to access the

router configuration Web User Interface.

3. Click Log in—there is no default password.

LAN WAN

ogue or

ISDN

Router

Modem

LAN WAN

Cable or DSL

Router Modem

LAN WAN

ogue or

ISDN

Router

Modem

4. Select Wizard from the menu.

The Setup Wizard will lead you through the basic router configuration process. If you are

unsure about any connection information required by the wizard, contact your ISP.

Note: For configuration details and USB printer installation instructions, refer to the

User

Guide

on the U.S. Robotics Installation CD-ROM.

5. Make a backup of your new configuration settings:

• Select the Toolbox menu.

• Click Backup Setting.

• Your system will prompt you to save or open the file. Select Save and click OK.

• Browse to the location at which you want the backup file saved and click Save.

Cable or DSL Users

To verify your Internet connection, launch a Web browser and register your product at

www.usr.com/productreg. If the page loads, you are finished with the installation procedure. If

the page does not load, proceed to Troubleshooting, later in this document.

Analogue or ISDN Users

To verify your Internet connection, click Connect in the Status page to initiate a dial-up session

with your ISP. The Status page will indicate whether or not the call was successful. If the settings

are correct, the analogue or ISDN modem can be used to connect to the Internet. If the connection

fails, verify that you entered the correct values.

Congratulations! The installation procedure is now complete.

Troubleshooting

I can’t connect to the Router’s Web User Interface.

Possible Solution 1:

Make sure all the Ethernet cables are properly and securely connected and the power cord is

plugged in.

Possible Solution 2:

Make sure that you correctly performed all the steps in the “Before You Begin” section of the

User

Guide

. If your computer is configured to use a static IP address, you must now reconfigure it to

Obtain an IP address automatically.

Possible Solution 3:

Make sure that your PC is using an IP address that is within the default range of 192.168.123.xxx.

Make sure the address of the subnet mask is 255.255.255.0. If necessary, the Default Gateway

should be 192.168.123.254. To verify all these settings, perform the following steps:

Windows Me, 98, and 95 Users:

• Click Windows Start > Run.

•Typewinipcfg and click OK.

• Check the IP Address, Subnet Mask, Default Gateway, and DNS server data to

make sure they are correct.

If the information is not correct, click Release All > Renew All.

Windows XP, 2000, and NT Users:

• Click Windows Start > Run.

•Typecmd and click OK.

• At the DOS prompt, type ipconfig /all and press Enter.

• Check the IP Address, Subnet Mask, Default Gateway, and DNS server data to

make sure they are correct. If the information is not correct:

•Typeipconfig /release and press Enter.

•Typeipconfig /renew and press Enter.

Possible Solution 4:

You need to verify the connection setting of your Web browser and that the HTTP Proxy feature of

your Web browser is disabled. You need to do this so that your Web browser can read the config-

uration pages inside your router.

• Launch your Web browser.

Internet Explorer users:

• Click Tools > Internet Options, and select the Connections tab.

• Select Never dial a connection, then click Apply.

• Click OK.

• Click Tools > Internet Options.

• Click the Connections tab, and click the LAN Settings button.

• Clear all the check boxes and click OK.

• Click OK.

Netscape Navigator users: Perform the following series of steps twice:

• Click Edit > Preferences.

• In the Category window, double-click Advanced.

• Click Proxies > Direct connection to the Internet. Then click OK.

I can’t access the Internet.

Possible Solution 1:

Make sure the power cord and all the Ethernet cables are connected correctly. This includes the

cables connecting the router, the modem, and all the PCs.

Possible Solution 2:

Reboot the router by unplugging and plugging in the power supply.

I do not know whether my IP address is static or dynamic.

Possible Solution:

Verify with your Internet Service Provider whether you have a dynamic or static IP address.

If you have a dynamic IP address, select Dynamic IP Address as the WAN Type in the Web User

Interface, and the router will automatically obtain the information it needs from your service pro-

vider.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels US Robotics Routeur sans fil

US Robotics

US Robotics usr5461 Manuel utilisateur

US Robotics

US Robotics USR8003 Manuel utilisateur

US Robotics

US Robotics USR5462 Manuel utilisateur

US Robotics

US Robotics 8000a Manuel utilisateur

US Robotics

US Robotics 8004 - Manuel utilisateur

US Robotics

US Robotics WIRELESS ROUTER 5466 Manuel utilisateur

US Robotics

US Robotics usr5465 Manuel utilisateur

US Robotics

US Robotics USR5462 Manuel utilisateur

US Robotics

US Robotics USR5463 Manuel utilisateur

US Robotics

US Robotics USR8000A-02 Manuel utilisateur

US Robotics

US Robotics USR8000A Manuel utilisateur

US Robotics

US Robotics USR8000 Manuel utilisateur

US Robotics

US Robotics Wireless Nd1 Router Manuel utilisateur

US Robotics

US Robotics Wireless 54Mbps ADSL Router Manuel utilisateur

US Robotics

US Robotics usr5461 Manuel utilisateur

US Robotics

US Robotics BROADBAND ROUTER - QUICK REV 1.1 Manuel utilisateur

US Robotics

US Robotics U.S.Robotics 8000 Manuel utilisateur

US Robotics

US Robotics 8004 - Manuel utilisateur

Manuels Routeur sans fil populaires d'autres marques

Milesight

Milesight UG67 Manuel utilisateur

Airlogic

Airlogic AirSync Class 1 Manuel du propriétaire

Samsung

Samsung WCH730B Manuel utilisateur

TELEFONICA

TELEFONICA USB Adapter Manuel utilisateur

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manuel utilisateur

Askey

Askey RAC2V1K Manuel utilisateur

Alloy

Alloy WLF2454AP-S Manuel utilisateur

TP-Link

TP-Link TL-WR542G Manuel utilisateur

NETGEAR

NETGEAR WNR2000v4 Manuel utilisateur

Hama

Hama 53120 Manuel utilisateur

Intellinet

Intellinet 524582 Manuel utilisateur

Asus

Asus RT-N10P Manuel utilisateur

D-Link

D-Link DIR-506L Manuel utilisateur

Sapido

Sapido GR297n Manuel utilisateur

Asus

Asus DSL-N55U Manuel utilisateur

AMTC

AMTC WR7502 Manuel utilisateur

Compaq

Compaq CP-2W - iPAQ Connection Point Manuel utilisateur

SMC Networks

SMC Networks WBR14-N2 FICHE Manuel utilisateur