UPM THM501 Manuel utilisateur
PROGRAMMABLE
THERMOSTAT
THM501
®
http://waterheatertimer.org/Woods-timers-and-manuals-old.html#Noma-Garrison
LEAVE BLANK
Features:
Extra-large LCD display with backlight — sets and displays house temperature (°C or °F),
day, hour and minute (in 12- or 24-hour format)
Temperature can be set in half degrees
Interfaces with humidifier for automatic humidity control
Interfaces with heating/air conditioning systems for automatic temperature control
Automatic change-over for HEATING/COOLING programs
Copy 1 day’s program to another day
Automatic ventilation
Selectable cycle rate
Usage monitor
Filter change reminder
Millivolt & 24 V compatible
Includes mounting hardware and 2 “AA” batteries
1
2
This thermostat requires2 “AA”size batteries (included)to operate.
Ensure the batteries are installed correctly. (REFER TO PAGE 31).
IMPORTANT - Getting Started
****
Once the batteriesare installed forthe first time,we recommend thatyou
perform a HARDRESET to setthe thermostat toits default settings.
Todo so,
While holding downthe LOCK key, press and release the RESET (R)
key located abovethe battery compartmenton the back. The LCD
screen will blankout momentarily.
The default temperaturescale is Celsius(°C). The temperaturedisplay will
immediately appear andflash for severalseconds. During thistime, you
may quickly selectFahrenheit (°F) by pressing theUP or DOWNkey. Or, if
left alone, thetemperature display willstop flashing andCelsius (°C) will
be selected.
First, press andhold the LOCK key.
Once the displayreappears, then releasethe LOCK key.
1
2
3
It is VERYIMPORTANT you choose your desired choice of Celsius (°C) or
Fahrenheit (°F) before you proceedwith the clockand program setting,as
this is aone-time setup process.The temperature scale(°C or °F)CANNOT
be changed afterwardsunless you performanother HARD RESETon the
thermostat. (REFER TOPAGES 17and 31).
Pull apart firmly to remove
the back cover from the
thermostat. DO NOT try to
pry open with a screwdriver.
Flip cover open
to access keys.
X
Battery Compartment -
insert 2 “AA” size
batteries as marked.
SIZE
AA
SIZE
AA
RESET (R) key
IMPORTANT - Getting Started
****
3
LOCK
key
AHEAD
PROGRAM
SET CLOCK
OPTION
HOLD
BACK
FAN
COPY
WEEKDAY
USAGE
MODE
HOME
UP
DOWN
LOCK
Function Key Descriptions
4
Set Time and Day
CLOCK
WEEKDAY
TEMPERATURE
TREND GRAPH
KEY LOCK
RELATIVE HUMIDITY
HOLD FUNCTION
OPERATION
MODES
USAGE
MONITOR
SET HUMIDITY
SET / PROGRAM
TEMPERATURE
FILTER CHANGE INDICATION
CURRENT (ROOM) TEMPERATURE
COMFORT ICONS
SYSTEM “ON”
INDICATION
AUTOMATIC
VENTILATION
BATTERY LOW
INDICATION
SET OPTIONS
COPY PROGRAM
LCD Display
5
OVERRIDE INDICATION
PROGRAM
NUMBER
Press SET CLOCK to start time setting. Thetime and SET symbol will flash.
Use AHEAD orBACK to setthe current time.
Press SET CLOCK again. The day and SET symbol will flash.
Use AHEAD orBACK to set the current day.
Press SET CLOCK to exit. (Or, if the HEAT mode isselected, press SET CLOCK twice to exit.
If you pressSET CLOCK only once, the thermostat will enterinto the Humidifier Control
function; refer topage 11).
Programs
This thermostat is equipped with 7 DAY PROGRAMMING. Monday + Tuesday + Wednesday
+ Thursday + Friday + Saturday + Sunday programming with 4 settings per day. This thermostat
is pre-programmed for your convenience or you can set your own programs as desired.
P1: MORNING
P2: DAY
P3: EVENING
P4: NIGHT
This is typically for the morning when you may prefer a warmer temperature.
This is an energy-savings mode for the time you are away from home. The setting
can be adjusted to minimize energy consumption.
This is for the time you return home and want the house at a comfortable temperature,
typically warmer settings during winter and cooler settings during summer.
This is a sleep mode. You may choose to set temperature for energy savings or
comfort as desired.
:
:
:
:
PERIOD
MORNING
DAY
EVENING
NIGHT
PTIME
P1
P2
P3
P4
6:00am
8:00am
5:00pm
10:00pm
HEAT SETPOINT COOL SETPOINT
oo
69.0 F (20.5 C)
oo
63.5 F (17.5 C)
oo
70.0 F (21.0 C)
oo
62.5 F (17.0 C)
oo
77.0 F (25.0 C)
oo
84.0 F (29.0 C)
oo
77.0 F (25.0 C)
oo
79.0 F (26.0 C)
SCHEDULE OF PRE-PROGRAMMED TIME AND TEMPERATURE SETTINGS
6
Press MODE until the HEAT symbol appears and press PROGRAM once. The P1 and SET PROGRAM
symbols will appear on the display.
To select the day that you want to program first, press WEEKDAY until the desired day appears.
(MON, TUE, WED, THU, FRI, SAT, SUN).
Use AHEAD or BACK to select the desired start time for P1.
- Program times can be set in increments of 10 minutes.
- Note: Program times are the same for heating and cooling. The times you choose here will be
used for the cooling program.
Use UP or DOWN (on extreme right) to set the desired temperature for P1.
- Temperature can be set in increments of 0.5°.
- The setpoint temperature range is 5°C to 32°C (41°F to 89°F) for heating.
After setting the desired time and temperature for P1, press PROGRAM again to display P2.
Again, use AHEAD or BACK to set the desired time, and use UP or DOWN to set the desired temperature.
Press PROGRAM to display P3. Repeat above steps to set the times and temperatures for P3 and P4.
To program another day of the week, press WEEKDAY to select the desired day. Then repeat the above
steps to set the desired times and temperatures for P1 to P4.
2
1
3
4
7
5
6
8
7
Heating Program
NOTE: To terminate the programming sequence at any time, press HOME.
NOTE: After the first day is programmed, you can also copy that day to any other day using the
Copy Program function. (Refer to page 8).
Cooling Program
Press MODE until the COOL symbol appears and repeat the programming procedure as you would for the
heating program.
- Note: The same program times are used for heating and cooling. Therefore, any changes made
to the times here will affect the program times for the heating program.
- The setpoint temperature range is 8°C to 35°C (48°F to 95°F) for cooling.
Note: The PROGRAM key can also be used at any time to review all the set programs. To terminate
the programming sequence at any time, press HOME.
Tip: Press and hold down the AHEAD/BACK or UP/DOWN key to change the numbers quickly.
Copy Program Function
This thermostat can copy program settings from one day to another using the COPY key.
Make sure the thermostat is engaged in the program setting mode by pressing PROGRAM. The
SET PROGRAM symbol will appear.
Select the day you wish to copy by pressing WEEKDAY. Once selected, press COPY. The COPY
symbol will appear.
By default, the following day will appear flashing, designating the day to be copied to. If you wish
to copy to this day, press COPY again. If not, choose the desired day to be copied to by pressing
WEEKDAY, then press COPY. The program settings (HEAT and COOL) from the first day will now
have been successfully copied to the day selected. Repeat these steps for each day you wish to
copy. 8
Table des matières
Autres manuels UPM Thermostat
UPM
UPM HTM621 Manuel utilisateur
UPM
UPM HTM511A Manuel utilisateur
UPM
UPM HTM511A Manuel utilisateur
UPM
UPM HTM311A Manuel utilisateur
UPM
UPM THM101B Manuel utilisateur
UPM
UPM THM301A Manuel utilisateur
UPM
UPM HTM611A Manuel utilisateur
UPM
UPM HTM621 Manuel utilisateur
UPM
UPM HTM511B Manuel utilisateur
UPM
UPM Elite THM701 Manuel utilisateur
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
